Copyright © 2008 Huawei Technologies Co., Ltd. All Rights Reserved No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions Ltd. and other Huawei trademarks are trademarks of Huawei Technologies Co., All other trademarks and trade names mentioned in this document are the property of their respective holders. Notice The information in this document is subject to change without notice.
Table of Contents What Is in Your Package ............................................. 2 Getting to Know Your E166 ......................................... 3 Preparation .............................................................. 5 Installation/Removal Guide ......................................... 7 Safety Information ...................................................10 Acronyms and Abbreviations ......................................
Getting to Know Your E166 The following figure shows the appearance of the E166. It is only for your reference. The actual product may differ. 1 2 3 6 4 5 n USB Interface It connects the E166 to a computer.
module (SIM/USIM) card. p Micro SD Card Slot It is where you insert the Micro Secure Digital Memory (SD) card q External Antenna Jack It connects the E166 to an external antenna. r Strap Hole s Indicator It indicates the status of the E166.
Preparation Requirements for the Computer To use the E166, the computer should meet the following requirements: USB Type A Receptacle, Compatible with USB 2. 0 Full Speed. Windows 2000 SP4, Windows XP SP2, Windows Vista. Your computer’s hardware system should meet or exceed the recommended system requirements for the installed version of OS. Resolution for the display: 800 × 600 or above. Getting Your E166 Ready Remove the USIM/SIM card slot from the E166.
Inserting the Micro SD Card (optional) Insert the micro SD card into the E166, as shown in the following figure. Note: Do not remove the micro SD card when it is being used. Removing the card during an operation may damage the micro SD card as well as the device, and data stored on the card may be corrupted.
Installation/Removal Guide On different operating systems (OSs), the installation and removal procedures may differ. Follow the system prompts during operation. Connecting the E166 with a Computer Note: First, power on the computer. Then connect the E166 with the computer. Otherwise, the E166 cannot be installed as normal. Plug the E166 into the USB interface of the laptop or desktop computer. You can connect the E166 to a laptop or desktop computer using the USB cable for better signals.
The OS automatically detects and recognises new hardware and starts the installation wizard. Follow the prompts of the installation wizard. After the program is installed, a shortcut icon for the E166 management program is displayed on the desktop. Starting the Management Program After the E166 is installed, the management program is launched automatically. Then every time the E166 is connected to the PC, the management program is launched automatically.
Removing the Management Program Click Start Menu. Click Control Panel. Click Add/Remove Program to remove the management program of the E166. Note: Before removing the management program, exit the management program.
Safety Information Read the safety information carefully to ensure the correct and safe use of your wireless device. Interference Do not use your wireless device if using the device is prohibited or when it cause danger or interference with electric devices. Medical Device Do not use your wireless device and follow the rules and regulations set forth by the hospitals and health care facilities. Some wireless devices may affect the performance of the hearing aids.
Area where the air contains chemical substances and particles (such as granule, dust, or metal powder) Area indicated with the "Explosives" sign Area indicated with the "Power off bi-direction wireless equipment" sign Area where you are generally suggested to stop the engine of a vehicle Traffic Security Observe local laws and regulations while using the wireless device. To prevent accidents, do not use your wireless device while driving.
WEEE Approval The wireless device is in compliance with the essential requirements and other relevant provisions of the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE Directive). RoHS Approval The wireless device is in compliance with the restriction of the use of certain hazardous substances in electrical and electronic equipment Directive 2002/95/EC (RoHS Directive). Laws and Regulations Observance Observe laws and regulations when using your wireless device.
Do not leave your wireless device and accessories in a place with a considerably low or high temperature. Use only accessories of the wireless device approved by the manufacture. Contact the authorized service center for any abnormity of the wireless device or accessories. Do not dismantle the wireless device or accessories. Otherwise, the wireless device and accessories are not covered by the warranty. Emergency Call This wireless device functions through receiving and transmitting radio signals.
instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual. Regulatory Information The following approvals and notices apply in specific regions as noted. CE Approval (European Union) The wireless device is approved to be used in the member states of the EU.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operati NOTICE: Changes or modifications made to this equipment not expressly approved by (manufacturer name) may void the FCC authorization to operate this equipment.
CAUTION: The USB Stick has been tested with specific integral antenna for SAR compliance with three notebook computers having vertical and horizontal USB slots. The device can be used in notebook computers with substantially similar physical dimensions, construction, and electrical and RF characteristics. Note: If this USB Stick is intended for use in any other portable device, you are responsible for separate approval to satisfy the SAR requirements of Part 2.1093 of FCC rules.
OS PIN SAR SIM UMTS USB USIM WCDMA Operating System Personal Identification Number Specific Absorption Rate Subscriber Identity Module Universal Mobile Telecommunications System Universal Serial Bus UMTS Subscriber Identity Module Wideband Code Division Multiple Access Version: V100R001_01 Part Number: 31018856 17
