WiMAX CPE Quick Start Huawei Technologies Co., Ltd. Huawei Industrial Base, Bantian, Longgang Shenzhen 518129 People’s Republic of China www.huawei.
Copyright © Huawei Technologies Co., Ltd. 2011. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. The product described in this manual may include copyrighted software of Huawei Technologies Co., Ltd. and possible licensors.
HUAWEI TECHNOLOGIES CO., LTD BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, OR LOST PROFITS, BUSINESS, REVENUE, DATA, GOODWILL OR ANTICIPATED SAVINGS. Import and Export Regulations Customers shall comply with all applicable export or import laws and regulations and will obtain all necessary governmental permits and licenses in order to export, re-export or import the product mentioned in this manual including the software and technical data therein.
Contents Before you begin ............................................................................................................................ 1 Getting to Know Your CPE ............................................................................................................ 1 Preparing for Installation ................................................................................................................ 5 Logging In to the Web-Based Utility .............................................
Thank you for purchasing WiMAX CPE! Before you begin Check the following items in the product package. If you find anything missing or damaged, contact the service provider. WiMAX CPE Dedicated Power Adapter Ethernet Cable Quick Start Getting to Know Your CPE The supported functions and actual appearance of the CPE may vary with the product you purchase. The following pictures are provided for illustration purpose only.
Front Panel 2
Indicator Status Description WiMAX On The indicators indicate the signal strength of the WiMAX network. When all the indicators are on, it indicates that the signal strength is at the highest level. Blink POWER LAN TEL WLAN Off The CPE is being upgraded or scanning frequency when they blink sequentially. The software is damaged when they blink randomly. The CPE is in the IDLE mode when the highest indicator blinks. There is no WiMAX network signal. On The CPE is powered on.
Rear Panel 4
Interface Description POWER The interface is used to connect to the output interface of the power adapter. TEL The interface is used to connect a telephone line. LAN The interface is used to connect the CPE to the computer. RESET Press and hold the button for one to eight seconds to restart the CPE. Press and hold the button for over eight seconds to restore the default settings of the CPE. Once you restore the default settings, all the customized data will be lost. Use this function with caution.
magnetic field, such as a microwave oven, a refrigerator, or a satellite dish antenna. Connecting the Cables Use the cables and the power adapter provided with the product. The cable connection figure is provided for illustration purpose. You can connect the devices to the CPE according to the actual requirements.
NOTE: During lightning storms, power off the CPE, and do not touch the antenna. Logging In to the Web-Based Utility Take the Windows XP operating system and the Internet Explorer 6.0 as examples. Ensure that the CPE is connected to the PC. To log in to the Web-based utility, do as follows: 1. Set the IP address of the PC and ensure that the IP address of the PC is in the same network segment as that of the CPE. NOTE: By default, the IP address of the CPE is 192.168.1.1 and the subnet mask is 255.255.
Troubleshooting The power indicator is not on. Ensure that the device is powered on. Ensure that the power adapter is compatible with the device. You cannot make calls. Ensure that the telephone is working normally and the telephone line is connected properly. Ensure that the VoIP service is configured correctly. If the problem persists, contact the local service provider. You cannot log in to the Web-based utility. Ensure that the device is powered on.
dish antenna. If the problem persists, contact the local service provider. The device or the power adapter overheats. The device may get heated after being used for a long time. Therefore, power off the device when you do not use the device. Place the device in a well-ventilated place and do not expose the device to direct sunlight.
Specifications WiMAX Parameters Standard IEEE 802.16e-2005 Frequency 2.496–2.69 GHz (BM623m) Interface LAN One Fast Ethernet (FE) interface TEL One Plain Old Telephone Service (POTS) interface Wi-Fi parameters Working mode IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE802.11b/g and IEEE 802.
Warnings and Precautions To use the device properly and safely, read these warnings and precautions carefully and strictly observe them during operation. Unless otherwise specified, the device described in this section includes the device and its accessories. Basic Requirements During storage, transportation, and operation of the device, keep it dry and prevent it from colliding with other objects. Do not dismantle the device.
Do not place any object (such as a candle or a water container) on the device. If any foreign object or liquid enters the device, stop using the device immediately, power it off, remove all the cables connected to it, and then contact an authorized service center. During thunderstorms, power off the device, and then remove all the cables connected to it to prevent it from getting damaged due to lightning strikes.
Do not use the power adapter if its cable is damaged. Otherwise, electric shocks or fires may occur. Ensure that the power adapter meets the specifications indicated on the device nameplate. Ensure that the power adapter meets the requirements of Clause 2.5 in IEC60950-1/EN60950-1 and it is tested and approved according to national or local standards. Safety of Children Keep the device and its accessories out of the reach of children.
accept any interference received, including interference that may cause undesired operation. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
WiMAX CPE Quick Start Huawei Technologies Co., Ltd. Huawei Industrial Base, Bantian, Longgang Shenzhen 518129 People’s Republic of China www.huawei.
