Specification Sheet

ManualsBrandsHSM ManualsIndustrial & Specialty ShreddersV-Press 820 Plus Vertical Baler

Table Of Contents

HSM Acknowledgment Form V-Press 820 plus.pdf
- HSM Acknowledgment Form V-Press 610.pdf
  - HSM Acknowledgment Form V-Press 605.pdf
    - HSM Acknowledgment Form V-Press 860 eco.pdf
      - HSM Acknowledgment Form V-Press 860 plus B
        HSM AcknowledgementForm_for_VPress_825-860-1160
      - HSM AcknowledgementForm_for_VPress_825-860-1160

HSM Acknowledgment Form V-Press 820 plus

HSM of America LLC · 419 Boot Road · Downingtown · PA 19335 · Tel. +1 800 613-2110 · info@hsm.us · www.hsm.us

HSM 06/2018 · All technical data and dimensions are approximate values. Technical and design modiﬁcations reserved.

Electrical connection

• The unloading of the truck and transportation to the installation location

will be arranged and paid by the customer (unless other agreements

declared in a contract)

• Forklift truck must be available to lift a minimum of 2,869 lbs

• Entrance door dimensions must be a minimum of 6'8"

• Potential floor loading must be adequate for machine

(floor loading max. = 102.4 lbs per ft², bale weight above)

• Ceiling height at operation location must be a minimum of 8'2"

• Please note that all offered prices are based upon the equipment already

being offloaded and set into installation location. If additional parts,

material, labor or equipment are required additional fees will apply

• Power connection of 480V - 60 Hz is required for operation

Page 1 of 3

Specifications

Pressing power in tons 18 tons

Motor in HP 6.4 HP

Voltage / Frequency 480 V / 60 Hz

Loading aperture W x H in inches 47“ x 22“

Bale weight in lbs (depending on material) up to 550

Bale size

47“ x 31“ x max. 39“

Cycle time in idle operation (theor.) in sec. 23

Acoustic level in dB(A) 62.5

Press chamber size W x D x H in inches

47.3“ x 30.7“ x 55,1“

Dimensions of machine* W x D x H in inches

67.8“ x 40.4“ x 98.4“

Transport dimensions of machine W x D x H in inches

67.8“ x 40.4“ x 78.4“

Machine weight in lbs 2,867

Strapping 4-fold with polyester tape

*External dimensions of the machine when set up for operation.

Rated power 6.4 HP

Rated power In 10.10 A

Total fuse 3 x 15 A CC/CF/G/J/T characteristic

Operating voltage 480 V

Frequency 60 Hz

Plug connection

Twist lock Devices 20 A, 3 Phase 480C/AC,

3-Pole, 4-Wire Grounding

Cable length of power supply approx. 118“

Summary of content (3 pages)

PAGE 1
HSM Acknowledgment Form V-Press 820 plus Specifications Pressing power in tons 18 tons Motor in HP 6.4 HP Voltage / Frequency 480 V / 60 Hz Loading aperture W x H in inches 47“ x 22“ Bale weight in lbs (depending on material) up to 550 Bale size 47“ x 31“ x max. 39“ Cycle time in idle operation (theor.) in sec. 23 Acoustic level in dB(A) 62.5 Press chamber size W x D x H in inches 47.3“ x 30.7“ x 55,1“ Dimensions of machine* W x D x H in inches 67.8“ x 40.4“ x 98.
PAGE 2
HSM Acknowledgment Form V-Press 820 plus Dimensions and space requirement HSM V-Press 820 plus Ceiling height min. 8‘2“ 5 approx. 2" 4 4 3 3 1025 1025 Einfüllöffnung Einfüllöffnung 558 5 Einfüllhöhe Einfüllhöhe 928 Required entire depth incl. swing range of the pressing door: 102“ approx. 12" approx. 12" Please note the projections! 36.46" 36.46" approx. 2" Transportation height 78.4" 6 Finale set up dimensions 2499 6 7 Transportation height 1990 Final set up dimensions 98.4" 7 8 .
PAGE 3
HSM Acknowledgment Form V-Press 820 plus __________________________________ (“Buyer”) hereby acknowledges they have purchased V-Press 820 plus (“Equipment”) from HSM of America, LLC (“HSM”) Buyer also acknowledges and agrees to all of the terms and conditions described in detail on the HSM website, including the limitation of liability provisions and warranty disclaimers. All of those terms apply provided in connection with the sale of the Equipment.