RC UNIVERS47 16 in 1 LCD touch screen remote control MANUAL all languages www.hqproducts.
The RC UNIVERS47 digital touch screen universal remote controls can work almost all brands of Televisions (TV), DVD-players and DVR-players (DVD), DVB receivers and (digital) Satellite receivers and Cable box (DVB), Video Recorders (VCR), Tuner receivers (TUNER), Tape receivers (TAPE), CDplayers (CD), Audio amplifiers and LD players and other Audio (AUX). You can controls 8 devices and add 8 new devices.
Realize the Keys SET For you start to set up (program) the remote control or show you the status in LCD screen. LEARN Used to setup learning functions. Macro Lets you make sequent operation for you home theater. Device Lets you to switch devices TV and TV1(VCR and VCR1,….) Page Lets you to switch between Page1 and Page2 of touch screen buttons. If you hold down for 3 seconds, you will see the date and year on LCD screen. Light Lets you control the touch screen back light. Power Turns the device on and off.
Note: Before you set up any function, you must activate the RC UNIVERS47 on first by touching the screen or pressing any key on the remote control. Battery Installation This remote control needs 4 batteries to work with. please refer to the direction marks inside the battery apartment and please put 4 pieces of fresh AAA in the battery apartment. Alkaline batteries are recommended since it has a large LCD screen to run out of more power consumption than the common universal remote control.
Delete a Device 1. Press the SET key on your remote control for more than 3 seconds, then release it. or keys to select to D e v i c e in LCD menu, and press 2. Press the the OK key. 3. Press the or keys to select to Delete in the LCD menu, and press the OK key LCD shows DeleteDEV, then you press device key to select your desired delete device(e.g. TV,DVD…). If no new add device ,LCD shows EMPT. 4. Press the OK key to save it and LCD shows Success! . 5. If you delete other device please repeat steps 3~4.
5. Check the function of the keys (e.g. POWER CH+ CH- VOL+ VOL- MUTE). If none of the keys of your new remote control can work, or most of the keys or key, until all basic work improperly, please try another code by the functions operate properly. 6. If you are satisfied with the code, please just press the OK key to save it. LCD shows Success! then it finishes the set up. You can press device key (e.g. TV) again to finish SET UP or use or to select other set up. Remark: 1.
Remark: 1. In case of you did not stop the search on time when device reacted, you may press the or key to search back to find the passed code. OK, EXIT are only used to set-up your new remote 2.The keys of control during the Auto Search, you can’t control your device for menu function at the moment until you quit from the set up . 3. When remote control searches through all codes, the remote control will stop at the beginning code of the search. 4.
LEARNING Learn a Command 1. Press a device key (e.g. TV) where you want to learn. 2. Press and hold the SET key for more than 3 seconds, then release it. 3. Press the key to Learning in LCD menu, and then press the OK key. 4. Press the key to Learn Key in LCD menu and then press the OK key LCD shows Select Key, if you exit learn mode ,please press the device key. 5. Select the (target) key you wanted to learn (e.g. Power). The LCD display PLS Send Signal in. 6.
Remark: 1. A selected target key can be multi learnt from different sources key, RC UNIVERS47 will store the final learnt signal only. 2. All usual function keys can be learnt. 3. Some code form may not be learnt by this remote control (due to the material cost limit.) 4. You can learn about 100 key totally for 8 devices and 8 new devices. Delete the Learnt Key 1. Press the device key (e.g. TV) where the command you like to delete from. 2. Press and hold the SET key for more than 3 seconds, then release it.
3. Scrol l key to Learning in LCD menu, and then press the OK key. 4. Scroll key to Delete DEV in LCD menu and then press the OK key. 5. You select device want to delete, and then press the OK key. 6. The LCD shows Sure Delet and then press the OK key, the LCD shows Success! . 7. Repeat step 5 to delete commands in other device key. 8. Press EXIT key to quit deletes operation. Delete All Learnt Keys 1. Press and hold the SET key for more than 3 seconds, then release it. 2.
6. Press the SET key to save the setting, LCD shows Success! then exit to current setup state. Macro Function Set up Macro Macro function let you make sequent operation for you home theater. Please press and hold the MACRO key and 1 key ( or 2,3 key), and then release them. The remote control will send out a sequent IR commands that you programmed before. You can set up a Macro by following below steps: 1. Press and hold the SET key for more than 3 seconds, then release it.
Remark: 1. You can set up to maximum 10 commands in a MACRO. 2.Make sure all the keys can send out signals, otherwise even if you programmed these keys into the MACRO, it still can not work properly when you operate MACRO function. You can check those keys by pressing them to see the relative Device buttons to flash or not before you set up MACRO. 3. Make sure the device must have relative conditions when you operate MACRO function.
Other Set-Up A. Set up Clock You can set up the clock on your RC UNIVERS47 LCD remote control and the clock will be displayed on the screen. 1. Press and hold the SET key for more than 3 seconds, then release it. or key to select the T i m e S e t in LCD menu, and then 2. Press the press the OK key. 3. Press the or key to select desired setup items such as Year, or key to change Month, Date, Day, Hour and Minute, then press the the year, month ,date ,day, hour and minute. or key to select AM or PM. 4.
control, then you can use this function to fix the volume and mute key of AUX, no matter which device you will use (even you will use TV, DVD, VCR etc), the volume and mute key on remote control still control the volume and mute of your amplifier. 1. Press and hold the SET key for more than 3 seconds, then release it. 2. Press the or key to select the O t h e r S e t in LCD menu, and then press the OK key. 3. Press the or key to select the V O L L o c k in LCD menu, and then press the OK key. 4.
Remark: You can fix all device codes but these device codes cannot be changed by neither Auto Search nor Brand Code Set up. D. Backlight If the background light is on, the background light will be lighted up when you press any key. 1. Press and hold the SET key for more than 3 seconds, then release it. or key to select the O t h e r S e t in LCD menu, and then 2. Press the press the OK key. 3. Press the or key to select the BackL i g h t in LCD menu, and then press the OK key.
E. Contrast Adjust If you are not satisfied the screen contrast of your remote control, you can use below steps to change it: 1. Press and hold the SET key for more than 3 seconds, then release it. 2. Press the or key to select the O t h e r S e t in LCD menu, then press the OK key. or key to select the C o n t r a s t in LCD menu, then 3. Press the press the OK key. or key to adjust contrast level, and then press the OK 4. Press the key when you satisfied the LCD shows S u c c e s s ! . 5.
press the OK key. or 4. Press the key to select On:xxSEC or All on. 5. Press the or key to select LCD on time (change length of LCD ontime from 5-60 seconds and 5 seconds as a step.). 6. Press the OK key to save setting and LCD display S u c c e s s ! for 1 second. You can press any device key to finish set up or press the EXIT key to last state, or you can use or to select other set up. Remark: Change length of LCD on time from 5-60 seconds and 5 seconds as a step. G. Beep 1.
