Specifications

ManualsBrandsHQ Power ManualsLightingKrystal RGV380 RGV laser projector

VDP2301RGVLD10 - VDP2601RGYLD10 - VDP3801RGVLD10

11/08/2011 ©Velleman nv

• Click on No File to remove the file from the list.

• Click OK to save the settings.

• When desired, a list of all DMX settings can be printed by clicking the Print button.

• To save the configuration, click on Save Config. The file must be saved as CONFIG.DAT as this is the

file that will be loaded automatically by the laser projector.

• Place the SD card back in the laser projector and switch the projector on. Make sure the SD CARD mode

switch [6] is pressed and the correct DMX address is set via the SD card controls.

6.3 PC controlled mode

• The PC controlled mode uses the ILDA (International Laser Display Association) standard for control signal

and file formats. The laser projector must be connected to a suitable PC running appropriate software (e.g.

Pangolin, Mamba, Phoenix…). Refer to §5 for the cable layout of the ILDA cable. More on the ILDA standard

can be found on http://www.laserist.org/standards.htm

IMPORTANT NOTE

Make sure to set the scan rate in the software equal to or lower than the actual scan rate of

the laser projector. Setting the scan rate too high may damage the laser projector; this

damage is not covered by the warranty.

• Press the PC MODE switch [6] to select PC mode.

• In this mode, the laser projector will receive its instructions and shows via the ILDA input port [10].

• Multiple laser projectors can be linked via the ILDA THRU port [9].

7. Cleaning and Maintenance

• All screws should be tightened and free of corrosion.

• The housing, visible parts, mounting supports and the installation location (e.g. ceiling, suspension,

trussing) should not be deformed, modified or tampered with e.g. do not drill extra holes in mounting

supports, do not change the location of the connections.

• Moving mechanic parts must not show any signs of wear and tear.

• The electric power supply cables must not show any damage. Have a qualified technician maintain the

device.

• Disconnect the device from the mains prior to maintenance activities.

• Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.

• There are no user-serviceable parts apart from the fuse.

• Contact your dealer for spare parts if necessary.

8. Technical specifications

VDP2301RGVLD10 VDP3801RGVLD10 VDP2601RGYLD10

Laser colour

/power

red 663nm/160mW 665nm/215mW 662nm/200mW

green 533nm/100mW 533nm/85mW 533nm/100mW

purple 408nm/200mW 405nm/200mW -

max. total output power 460mW 500mW 300mW

max. scan speed 20 Kpps 20 Kpps 20 Kpps

optical angle ±20° ±20° ±20°

Power supply AC 110-240V 50/60Hz

Power consumption 300W

Dimensions 200 x 260 x 450mm 200 x 260 x 310mm

Total Weight 7.0kg ±5.5kg

Laser type DPSSL (Diode Pumped Solid State Laser) green: DPSSL

red: semiconductor laser diode

Laser class Class 3B

Laser life >5000h

Use this device with original accessories only. Velleman nv cannot be held responsible in the event

of damage or injury resulted from (incorrect) use of this device. For more info concerning this

product and the latest version of this user manual, please visit our website www.hqpower.eu. The

information in this manual is subject to change without prior notice.

The copyright to this manual is owned by Velleman nv. All worldwide rights reserved.

No part of this manual or may be copied, reproduced, translated or reduced to any electronic medium or otherwise without