Service Handbook HP x4000 Workstation Manufacturing Part Number: A6068-IE002 Edition xxxx © Copyright 2001 Hewlett-Packard Company.
Legal Notices The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Contents 1. HP x4000 Service Information Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 x4000 System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 System Board Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 BIOS Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Upgrading Memory . . . . . . . . . . . . . . . .
Contents 4
1 HP x4000 Service Information Chapter 1 5
HP x4000 Service Information Overview Overview This chapter contains information about: • “x4000 System Board” on page 7 • “BIOS Identification” on page 9 • “Upgrading Memory” on page 10 • “Replacing or Upgrading a Processor” on page 13 Chapter 2 contains ordering information for x4000 accessories. Chapter 3 contains ordering information for x4000 parts.
HP x4000 Service Information x4000 System Board x4000 System Board Chapter 1 7
HP x4000 Service Information x4000 System Board System Board Switches The system board includes a 4-pole DIP switch, which lets you configure BIOS functions. Because the switches are read only at system start up, you must change the switch positions when the Workstation is shut down. Switch Function Default Comment 1 Clear BIOS password Off Clears both Administrator and User passwords, if they have been set.
HP x4000 Service Information BIOS Identification BIOS Identification The system BIOS is identified by the version number XX.YM.
HP x4000 Service Information Upgrading Memory Upgrading Memory The memory for the HP x4000 Workstation is located on a Memory Expander Card, which plugs into the system board. There are two memory banks (RDRAM channels): • Bank I includes sockets 1B (J1), 2B (J2), 1A (J5), and 2A (J6). • Bank II includes sockets 3B (J3), 4B (J4), 3A (J7), and 4A (J8). This allows for a total of 8 RIMMs. You must adhere to the following rules when loading memory: • RIMMs must be loaded in matched pairs.
HP x4000 Service Information Upgrading Memory Figure 1-1 x4000 Memory Expander Card (MEC) 2A (J6) 1A (J5) 4B (J4) 3B (J3) 4A (J8) 3A (J7) 2B (J2) 1B (J1) Memory Bank I consists of: RIMM pair 1: 1A (J5) and 1B (J1) RIMM pair 2: 2A (J6) and 2B (J2) Memory Bank II consists of: RIMM pair 3: 3A (J7) and 3B (J3) RIMM pair 4: 4A (J8) and 4B (J4) If a m em ory bank only contains 1 pair of RIMMs, the remaining 2 connectors m ust contain CRIMM s to ensure continuity.
HP x4000 Service Information Upgrading Memory Figure 1-2 Replacing or Upgrading Memory 1 Pair of RIMMs 2 Pairs of RIMMs CRIMM RIMM 1A RIMM 2A RIMM 1A CRIMM RIMM 1B P1 - edge 3 Pairs of RIMMs RIMM 2B RIMM 1B Memory Bank I P1 - edge 4 Pairs of RIMMs RIMM 2A RIMM 1A CRIMM RIMM 3B RIMM 2A RIMM 1A RIMM 4B RIMM 3B CRIMM RIMM 3A RIMM 2B RIMM 1B RIMM 4A RIMM 3A RIMM 2B RIMM 1B P1 - edge Memory Bank II P1 - edge Note: RIMM 1A and 1B are a matched pair, 2A and 2B are a matched pair, 3A and 3B are
HP x4000 Service Information Replacing or Upgrading a Processor Replacing or Upgrading a Processor The x4000 Workstation can have two processors. The processors must be identical. CAUTION If you are upgrading your current processor, you must update the BIOS. The latest BIOS is located at www.hp.com/workstations/support. If you are adding a second processor, you must update your operating system (see “Updating Your Operating System” on page 16).
HP x4000 Service Information Replacing or Upgrading a Processor 8. Remove the two heatsink clips by pressing the release lever on the clips. Then lift off the heatsink. There is a thermal interface material between the heatsink and the processor. This may cause the processor to stick to the heatsink. Figure 1-3 Removing a Processor Step 8 Step 10 9. Remove the thermal interface material from the heatsink and discard it. You can leave any residue that remains on the heatsink.
HP x4000 Service Information Replacing or Upgrading a Processor 4. Open the hard disk drive cage. 5. Remove the Chassis Beam Assembly. 6. Remove the MEC card. 7. Ensure the processor is correctly oriented by matching the notches on the processor to the notches on the ZIF socket. Then carefully lower the new processor into place. When the processor is fully inserted, close the ZIF lever. CAUTION Figure 1-4 Be extremely careful when you insert the processor.
HP x4000 Service Information Replacing or Upgrading a Processor 15. Reconnect all the power and telecommunications cables. 16. Update your operating system (see page 16). Updating Your Operating System If you are adding a second processor to a Workstation (or removing a processor), you must update the operating system to reflect these changes. Windows 2000 To update the operating system in Windows 2000: 1. Go to the Control Panel by selecting Start > Settings > Control Panel. 2. Select the System icon. 3.
2 Accessory Ordering Information Chapter 2 17
Accessory Ordering Information Supported Accessories Supported Accessories Intel Xeon Processors 1.5 GHz 1.
Accessory Ordering Information Supported Accessories North America (ABA) Australia (ABG) Japan (ABJ) Argentina (AC8) United Kingdom (ACC) Switzerland (ACD) South Africa (ACQ) South America (AKH) Israel (AKJ) Chapter 2 19
Accessory Ordering Information Mass Storage Device Guide Rails Mass Storage Device Guide Rails Extra guide rails are attached to the side of the Workstation chassis for additional mass storage device installations. Depending on the device to be installed, dedicated guide rails are required and are easily recognized by their distinct size and color. The following table indicates the device, location, and required rails. Device to be Installed Location Required Rails Installing the Rails 5.
3 HP x4000 Parts Information Chapter 3 21
HP x4000 Parts Information x4000 Parts and Part Numbers x4000 Parts and Part Numbers 1 1a 1d 1g 1b 2 2b 1e 2a 1c 1f 3 22 Chapter 3
HP x4000 Parts Information x4000 Parts and Part Numbers Table 3-1 Item Parts List Description Replacement Part Number Exchange Part Number Mechanical and Power 1 Chassis Assembly — — 1a Chassis door (left cover) A6068-62004 — 1b 465W power supply assembly A6068-00006 — 1c PCI fan (92mm) and speaker assembly A6068-62016 — 1d Rear system fan (120mm) A6068-62015 — 1e Hard disk drive fan (60mm) A6068-62014 — 1f Chassis beam assembly with graphics card retainer A6068-62012 — 1g
HP x4000 Parts Information x4000 Parts and Part Numbers Table 3-1 Parts List Item Description NS x4000 Miscellaneous Parts Kit: • • • • • • • • • • • NS NS NS NS NS Replacement Part Number Per kit qty. A6068-67901 1 Tamper detect switch assy 1 Keylock and keys 4 Cable routing clip 4 Rails, no screw (3.25” and 5.
HP x4000 Parts Information x4000 Parts and Part Numbers Table 3-1 Item Description NS Keyboards: Parts List Replacement Part Number US English and Chinese (ABA & AB2) Canadian French (ABC) German (ABD) Spanish (ABE) French (ABF) Latin America Spanish (ABM) Swiss (ABP & APQ) Sweden (ABS) UK English (ABU) Italian (ABZ) Korean (AB1) Taiwanese (AB0) Japanese (ABJ) European English (ABB) NS Exchange Part Number C4742-60101 C4742-60102 C4742-60103 C4742-60104 C4742-60105 C4742-60108 C4742-60111 C4742-60112
HP x4000 Parts Information Documentation Documentation Table 3-2 Manuals and Documentation Description Part Number Comments Getting Started Guide A6068-90000 Paper document Accessory Installation Guide A6068-90010 Paper document Technical Reference Manual electronic file only Online documentation (electronic files) can be downloaded from: www.hp.
HP x4000 Parts Information Software and Training CDs Software and Training CDs Table 3-3 Software and Training CDs Contains:a Windows Recovery/Install CD Kits: Kit Number Windows 2000 Windows NT English US (ABA) A6068-95001 A6068-92101 A6068-92137 German (ABD) A6068-95002 A6068-92103 A6068-92104 French (ABF) A6068-95003 A6068-92105 A6068-92106 Japanese (ABJ) A6068-95004 A6068-92107 A6068-92108 English UK (ABU) A6068-95005 A6068-92109 A6068-92110 English Europe (ABB) A6068-95006 A
HP x4000 Parts Information Software and Training CDs 28 Chapter 3
