HP WBEM TC Document Number: P00116 Date: 11/29/06 Version: 1.0.2 HP Power Supply Physical Asset Profile © Copyright 2008 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Contents 1 2 2.1 2.2 2.3 3 4 5 6 7 7.1 7.2 7.3 7.4 8 9 9.1 9.2 10 10.1 10.2 10.3 10.4 10.5 11 Scope ..................................................................................................................................... 5 Normative References ........................................................................................................... 5 Approved References ............................................................................................................
Foreword The HP Power Supply Physical Asset Profile P00116 was prepared by the HP WBEM TC. Version 1.0.
Introduction The information in this specification should be sufficient for a provider or consumer of this data to identify unambiguously the classes, properties, methods, and values that shall be instantiated and manipulated to represent power supplies in HP systems. The target audience for this specification is implementers who are writing CIM based providers or consumers of management interfaces representing the component described in this document. 4 Version 1.0.
1 Scope The HP Power Supply Physical Asset Profile extends the management capability of referencing profiles by adding the capability to represent the physical power supplies in HP specific ways. 2 Normative References The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. 2.
mandatory used to indicate requirements strictly to be followed in order to conform to the document and from which no deviation is permitted may used to indicate a course of action permissible within the limits of the document need not used to indicate a course of action permissible within the limits of the document optional used to indicate a course of action permissible within the limits of the document referencing profile Indicates a profile which owns the definition of this class and can include a refer
Scoping Class: Same as parent profile Extends: DMTF DSP1011, Physical Asset Profile 1.0.0 The HP Power Supply Physical Asset profile extends DMTF DSP1011 to add physical power supply characteristics that are specific to HP systems. Table 1 – Related Profiles Profile Name Organization Version Relationship DSP1011 – Physical Asset Profile DMTF 1.0.0 Mandatory P00100 – HP Profile Registration Profile HP WBEM TC 1.0.0 Mandatory P00103 – HP Power Supply Profile HP WBEM TC 1.0.
Figure 1 – HP Power Supply Physical Asset Profile: Class Diagram CIM_Realizes CIM_Container see DMTF Physical Asset profile HP_RealizesPowerSupply see DMTF Physical Asset profile HP_SystemPhyiscalPowerSupply CIM_PackageInSlot see DMTF Physical Asset profile HP_PowerSupplyInSlot Figure 2 – HP Power Supply Physical Asset Profile: Inheritance Hierarchy Diagram 7 Implementation Requirements This section details the requirements related to the arrangement of instances and properties of instances for
9.1 Use Cases Object Diagram Figure 3 represents a possible instantiation of the HP Power Supply Physical Asset Profile. In this case, system1 has two power supplies, ps1 and ps2. Ps1 and ps2 are associated to power supply modules ps1 and ps2 via HP_RealizesPowerSupply. These power supply modules are respectively associated to slots psslot1 and psslot2 via HP_PowerSupplyInSlot. The power supply modules are all also associated to chassis1 via HP_SystemPhysicalPowerSupply.
system1:CIM_ComputerSystem HP_HostedPowerCollection powercollection1:HP_Power Collection GroupOperationalStatus: (OK) HP_SystemPowerSupply ps2:HP_PowerSupply OperationalStatus: (OK) HP_MemberOfPowerCollection ps1:HP_PowerSupply OperationalStatus: (OK) HP_RealizesPowerSupply ps1:HP_PowerSupplyModule HP_RealizesPowerSupply ps2:HP_PowerSupplyModule HP_PowerSupplyInSlot psslot1:CIM_Slot HP_PowerSupplyInSlot psslot2:CIM_Slot psslot3:CIM_Slot psslot4:CIM_Slot CIM_Container HP_SystemPhysicalPower Su
10 CIM Elements The implementation requirements for the classes and properties described in this section are defined in the “Implementation Requirements” section (Section 7). Table 2 – CIM Elements – HP Power Supply Profile Element Name Requirement Description Classes HP_PowerSupplyModule Mandatory See Sections 7.1 and 10.1 HP_RegisteredProfile Mandatory See Section 10.2 HP_RealizesPowerSupply Mandatory See Sections 7.2 and 10.3 HP_SystemPhysicalPowerSupply Mandatory See Sections 7.3 and 10.
10.4 HP_SystemPhysicalPowerSupply HP_SystemPhysicalPowerSupply is used to represent the association between CIM_PhysicalPackage and HP_PowerSupplyModule. Table 6 – Class: HP_SystemPhysicalPowerSupply Properties Requirement Notes GroupComponent Mandatory Key: References HP_ComputerSystemChassis PartComponent Mandatory Key: References HP_PowerSupplyModule 10.5 HP_PowerSupplyInSlot HP_PowerSupplyInSlot is used to represent the association between HP_PowerSupplyModule and CIM_Slot.
ANNEX A (normative) Change Log Version Date 0.1 5/30/06 Initial draft 1.0 5/31/06 Updated properties and fixed cross reference errors 1.0 11/29/06 1.0.1 5/16/08 1.0.2 7/17/08 Version 1.0.
ANNEX B (informative) Acknowledgments 14 Version 1.0.
ANNEX C (informative) Included WBEM TC CR Numbers CR Number Date CR00106 5/31/06 Version 1.0.
Bibliography This section contains a list of the external references and dependencies for this specification. 16 Version 1.0.
