HP WBEM TC Document Number: P00115 Date: 09/11/08 Version: 1.1.0 HP Fan Physical Asset Profile © Copyright 2008 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Contents 1 2 2.1 2.2 2.3 3 4 5 6 7 7.1 7.2 7.3 7.4 7.5 8 9 9.1 9.2 10 10.1 10.2 10.3 10.4 10.5 11 Scope ..................................................................................................................................... 5 Normative References ........................................................................................................... 5 Approved References ............................................................................................................
Foreword The HP Fan Physical Asset Profile P00115 was prepared by the HP WBEM TC. Version 1.1.
Introduction The information in this specification should be sufficient for a provider or consumer of this data to identify unambiguously the classes, properties, methods, and values that shall be instantiated and manipulated to represent fans in HP systems. The target audience for this specification is implementers who are writing CIM based providers or consumers of management interfaces representing the component described in this document. 4 Version 1.1.
1 Scope The HP Fan Physical Asset Profile extends the management capability of referencing profiles by adding the capability to represent the physical fans in HP specific ways. 2 Normative References The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. 2.
mandatory used to indicate requirements strictly to be followed in order to conform to the document and from which no deviation is permitted may used to indicate a course of action permissible within the limits of the document need not used to indicate a course of action permissible within the limits of the document optional used to indicate a course of action permissible within the limits of the document referencing profile Indicates a profile which owns the definition of this class and can include a refer
Scoping Class: Same as parent profile Extends: DMTF DSP1011, Physical Asset Profile 1.0.0 The HP Fan Physical Asset profile extends DMTF DSP1011 to add physical fan characteristics that are specific to HP systems. Table 1 – Related Profiles Profile Name Organization Version Relationship DSP1011 – Physical Asset Profile DMTF 1.0.0 Mandatory P00100 – HP Profile Registration Profile HP WBEM TC 1.0.0 Mandatory P00102 – HP Fan Profile HP WBEM TC 1.0.
CIM_Container CIM_Realizes see DMTF Physical Asset profile HP_RealizesFan see DMTF Physical Asset profile HP_SystemPhysicalFan CIM_PackageInSlot see DMTF Physical Asset profile HP_FanInSlot Figure 2 – HP Fan Physical Asset Profile: Inheritance Hierarchy Diagram 7 Implementation Requirements This section details the requirements related to the arrangement of instances and properties of instances for implementations of this profile. 7.
7.3 HP_SystemPhysicalFan There shall be one instance of HP_SystemPhysicalFan instantiated for each instance of HP_FanModule. This class associates instances of HP_FanModule with CIM_PhysicalPackage. 7.4 HP_FanInSlot If an instance of CIM_Slot representing the fan slot exists, there shall be one instance of HP_FanInSlot instantiated for each instance of HP_FanModule. This class associates an instance of HP_FanModule with a corresponding instance of CIM_Slot. 7.5 CIM_Slot.
system1:CIM_ComputerSystem HP_HostedCoolingCollection coolingcollection1:HP_Cooli ngCollection GroupOperationalStatus: (OK) HP_SystemFan HP_SystemFan fan2:HP_Fan OperationalStatus: (OK) HP_MemberOfCoolingCollection fan1:HP_Fan HP_MemberOfCoolingCollection OperationalStatus: (OK) HP_RealizesFan HP_RealizesFan Fm1:HP_FanModule Fm2:HP_FanModule OperationalStatus: (OK) Element Name: “Fan 1” FanType: 11 (Chassis) Description: Fan 1 provides cooling for the Chassis: Status is OK.
9.2 Retrieve the Fan Status for a Fan Module For the given instance of HP_FanModule, retrieve associated instances of HP_Fan through the HP_RealizesFan association. Observe the HP_Fan.OperationalStatus property for this instance. 10 CIM Elements The implementation requirements for the classes and properties described in this section are defined in the “Implementation Requirements” section (Section 7).
OtherRegisteredOrganization 10.3 Mandatory “HP WBEM TC” HP_RealizesFan HP_RealizesFan is used to represent the association between HP_Fan and HP_FanModule. Table 5 – Class: HP_RealizesFan Properties Requirement Notes Antecedent Mandatory Key: References HP_FanModule Dependent Mandatory Key: References HP_Fan 10.4 HP_SystemPhysicalFan HP_SystemPhysicalFan is used to represent the association between CIM_PhysicalPackage and HP_FanModule.
ANNEX A (normative) Change Log Version Date 0.1 5/30/06 Initial draft 1.0 5/31/06 Updated properties and fixed cross reference errors 1.0 11/29/06 1.0.
ANNEX B (informative) Acknowledgments 14 Version 1.1.
ANNEX C (informative) Included WBEM TC CR Numbers CR Number Date CR00106 5/31/06 Create HP profile for the environmental model CR00143 9/11/08 Detailed string properties Version 1.1.
Bibliography This section contains a list of the external references and dependencies for this specification. 16 Version 1.1.
