HSG80 ACS Solution Software Version 8.7 for Compaq Tru64 UNIX Installation and Configuration Guide
Table Of Contents
- HSG80 ACS Solution Software Version 8.7 for Compaq Tru64 UNIX Installation and Configuration Guide
- About this Guide
- 1- Planning a Subsystem
- Defining Subsystems
- What is Failover Mode?
- Selecting a Cache Mode
- Enabling Mirrored Caching
- What is the Command Console LUN?
- Determining Connections
- Assigning Unit Numbers
- What is Selective Storage Presentation?
- 2- Planning Storage Configurations
- Where to Start
- Determining Storage Requirements
- Configuration Rules for the Controller
- Addressing Conventions for Device PTL
- Choosing a Container Type
- Creating a Storageset Profile
- Planning Considerations for Storageset
- Changing Characteristics through Switches
- Specifying Storageset and Partition Switches
- Specifying Initialization Switches
- Specifying Unit Switches
- Creating Storage Maps
- 3- Preparing the Host System
- Installing RAID Array Storage System
- Making a Physical Connection
- Preparing LUNs for Access by Tru64 UNIX FileSystem
- DECsafe Available Server Environment (ASE)
- HSG80 Units and Tru64 UNIX Utilities
- Solution Software Upgrade Procedures
- New Features, ACS 8.7 for Tru64
- 4- Installing and Configuring HSG Agent
- 5- FC Configuration Procedures
- Establishing a Local Connection
- Setting Up a Single Controller
- Setting Up a Controller Pair
- Configuring Devices
- Configuring Storage Containers
- Assigning Unit Numbers and Unit Qualifiers
- Configuration Options
- Verifying Storage Configuration from Host
- 6- Using CLI for Configuration
- 7- Backing Up, Cloning, and Moving Data
- A- Subsystem Profile Templates
- Storageset Profile
- Storage Map Template 1 for the BA370 Enclosure
- Storage Map Template 2 for the second BA370 Enclosure
- Storage Map Template 3 for the third BA370 Enclosure
- Storage Map Template 4 for the Model 4214R Disk Enclosure
- Storage Map Template 5 for the Model 4254 Disk Enclosure
- Storage Map Template 6 for the Model 4310R Disk Enclosure
- Storage Map Template 7 for the Model 4350R Disk Enclosure
- Storage Map Template 8 for the Model 4314R Disk Enclosure
- Storage Map Template 9 for the Model 4354R Disk Enclosure
- B- Installing, Configuring, and Removing the Client
- C- SWCC Agent in TruCluster Environment
- SWCC Overview
- Running the SWCC Agent on a V4.0G Cluster
- Running the SWCC Agent under ASE Services
- Running the SWCC Agent on a V5.x Cluster
- Problems with Running the Agent on Multiple Clusters
- Configure the Controller
- Use Multiple-Bus Failover Mode
- Verify That the HSG80/HSG60 Unit Offsets Are Zero
- Install and Run the Agent on One Cluster Member
- Example of Installing the Agent on a Cluster Member
- Create the CAA Action Script
- Create the CAA Resource
- Glossary
- Index
Installing and Configuring HSG Agent
4–8 HSG80 ACS Solution Software Version 8.7 for Compaq Tru64 UNIX Installation and
Configuration Guide
You are asked for a password, which is required to do configurations within the
Client software. If an old password is found, you are asked if you want to use it.
Enter Subsystem Information
15. Enter your case-sensitive password that has 4 to 16 characters, and press the
Enter key. You are asked to retype the password.
16. Retype the password and press the Enter key.
Once the password has been entered, the system scans for subsystems. You will be
asked for the name and monitoring interval of each RAID subsystem found.
17. Enter the subsystem name in lowercase letters, and press the Enter key. You are
asked for the monitoring interval. The monitoring interval is the rate at which the
Agent queries the specified subsystem for status.
18. Enter the monitoring interval in seconds, and press the Enter key. The monitoring
interval determines how often the Agent polls the subsystems. You are asked if the
displayed information is correct.
19. If the displayed information is correct, select option y and press the Enter key.
You are asked if you want Email enabled.
Configure Email Notification Details
20. To enable the Email, select option y and press the Enter key. The software asks
for the address of the person to notify.
21. Enter the address of the person to notify, and press the Enter key.
22. From the displayed menu, enter the notification level: 1, 2, or 3.
Table 4–5 provides the definitions of the Email notification options:
Table 4–5: Definitions of Email Notification Options
Term Definition
Critical
Errors
Notifies you of errors that would prevent you from accessing data;
for example, a disk failing or a client system not available on the
network.
Warnings Notifies you when something is broken, but its breakage does not
prevent you from accessing data; for example, the RAID
degrading or losing a fan.