Maintenance and Service Guide HP MultiSeat ms6200 and HP t200 Zero Client For MultiSeat
© Copyright 2011 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft and Windows are trademarks of Microsoft Corporation in the U.S. and other countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
About This Book WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. NOTE: Text set off in this manner provides important supplemental information.
iv About This Book
Table of contents 1 Product Features ............................................................................................................................................ 1 HP MultiSeat ms6200 ........................................................................................................................... 1 Standard Configuration Features ......................................................................................... 1 Front Panel Components ......................................
Licensing and Support ........................................................................................................................ 14 External Links ..................................................................................................................................... 14 Troubleshooting .................................................................................................................................. 14 LED Codes ......................................................
5 Removal and Replacement Procedures ..................................................................................................... 38 Preparation for Disassembly .............................................................................................................. 38 Access Panel ...................................................................................................................................... 39 Front Bezel .................................................................
USB .................................................................................................................................................... 77 Microphone ......................................................................................................................................... 78 Headphone ......................................................................................................................................... 78 Line-in Audio .......................................
1 Product Features HP MultiSeat ms6200 Standard Configuration Features Features may vary depending on the model. For a complete listing of the hardware and software installed in the computer, run the diagnostic utility (included on some computer models only). Figure 1-1 Small Form Factor Configuration NOTE: The MultiSeat computer can also be used in a tower orientation. For more information, see Using the Small Form Factor Computer in a Tower Orientation on page 75 in this guide.
Front Panel Components Drive configuration may vary by model. Some models have a bezel blank covering one or more drive bays. Figure 1-2 Front Panel Components Table 1-1 Front Panel Components 1 5.25-inch Optical Drive 5 Microphone/Headphone Connector 2 Dual-State Power Button 6 3.5-inch Media Card Reader (optional) 3 Power On Light 7 Hard Drive Activity Light 4 USB (Universal Serial Bus) Ports 8 Headphone Connector NOTE: The Power On Light is normally green when the power is on.
Media Card Reader Components The media card reader is an optional device available on some models only. Refer to the following illustration and table to identify the media card reader components. Figure 1-3 Media Card Reader Components Table 1-2 Media Card Reader Components No.
Rear Panel Components Figure 1-4 Rear Panel Components 1 RJ-45 Network Connector 6 DisplayPort Monitor Connector 2 Serial Connector 7 VGA Monitor Connector 3 PS/2 Mouse Connector (green) 8 PS/2 Keyboard Connector (purple) 4 Power Cord Connector 9 Line-Out Connector for powered audio devices (green) 5 Universal Serial Bus (USB) ports 10 Line-In Audio Connector (blue) Serial Number Location Each computer has a unique serial number and a product ID number that are located on the top cover
HP t200 Zero Client Front Panel Components For more information, http://www.hp.com and search for your specific t200 Zero Client model to find the model-specific QuickSpecs. Figure 1-6 Front panel components (1) Power LED (3) Line-out (headphone) audio connector (2) Line-in (microphone) connector (4) USB 2.
Rear Panel Components For more information, http://www.hp.com and search for your specific t200 Zero Client model to find the model-specific QuickSpecs.
2 HP MultiSeat Computing Solution – Best Practices Offerings of Microsoft® Windows® MultiPoint™ Server 2011 OEM Standard ● HP MultiSeat ms6200 Desktop (the host PC) ships preinstalled from the factory with Windows MultiPoint Server 2011, which includes the server Certificate of Authenticity (COA) and the host station Client Access License (CAL) ● HP zero clients sell separately; client operating system CAL is included ● HP preinstalls Windows MultiPoint Server 2011 in 18 languages ● Domain join not
Academic Volume License ● HP MultiSeat ms6200 Desktop sold with FreeDOS installed and no Client Access License (CAL) provided ● Requires the purchase of the Academic Volume License version of MultiPoint Server 2011 ● Device drivers must be downloaded from HP and installed ● HP zero clients do not include the user CAL ● Available in multiple languages: 18 fully localized, 20 with operating system localized (MultiPoint Manager is not localized) ● Domain join allowed ● Operating system maximum num
Topology ● Windows MultiPoint Server 2011 ◦ Windows MultiPoint Server 2011 supports PS/2 keyboard/mouse on the host system. ◦ Windows MultiPoint Server 2011 supports audio and microphone on the host PC station. NOTE: For this to function, the host stations must be configured using PS/2 keyboard and mouse. It will not function with USB keyboard or mouse. ◦ Windows MultiPoint Server 2011 supports daisy-chaining of client devices connected by USB cable.
If the optional DC adapter is connected to a working power outlet or to the monitor, the t200 Zero Client supports a USB keyboard, a USB mouse, and two 500 mA (high power) USB devices.
Best Practices for Setting Up a MultiSeat Environment A USB-connected environment is ideal when plug-and-play simplicity is desired or in settings with no Ethernet network infrastructure. An Ethernet-connected environment is ideal when the distance needed between the host PC and its clients must be greater than USB allows. It can also help reduce cable clutter around the host PC. NOTE: If the t200 Zero Client drivers are not preinstalled on your host PC, please download them from the HP website. Go to hp.
● Ethernet-connected t200 Zero Clients look like local USB devices to the operating system as displayed in MultiPoint Manager. ● There are two types of hardware reset: ◦ Clear assignment—hold recessed reset button while powering on until LED blinks blue/ amber ◦ Clear all (factory defaults)—hold the reset button for seven seconds until the LED goes out.
Best Practices for Installation of Drivers with the Volume License Operating System Recommended Method (Automatic Driver Installation) Before installing the Windows MultiPoint Server 2011 Volume License operating system from DVD, go to www.hp.com and search for drivers for your host PC model. Choose the MultiPoint 2011 OS then locate and download the "HP Install Assistant" Softpaq. (Using this method, you will not need to download any other driver Softpaqs.
Performance Considerations Consider the following when evaluating performance on a MultiSeat solution: ● Each client session, including the host system, will offer native resolution of the monitor attached to the client/host. The MultiPoint operating system does not attempt to reduce the resolution or color depth of each session. ● Performance will be a factor of the application running in each session and the number of client sessions running per host system.
Switching from USB to PS/2 mouse or keyboard (and vice versa) requires the stations to be remapped. Cause Solution The MultiPoint operating system stores the previous mapping of keyboards and mice to each display, and it attempts to continue to use that mapping. Use the Remap all stations feature in the MultiPoint Manager when changing keyboard or mouse configurations in any way. The host USB mouse has failed on some USB ports after re-associating .
3 Computer Setup (F10) Utility Computer Setup (F10) Utilities Use Computer Setup (F10) Utility to do the following: 16 ● Change factory default settings. ● Set the system date and time. ● Set, view, change, or verify the system configuration, including settings for processor, graphics, memory, audio, storage, communications, and input devices. ● Modify the boot order of bootable devices such as hard drives, optical drives, or USB flash media devices.
● Solve system configuration errors detected but not automatically fixed during the Power-On SelfTest (POST). ● Replicate the system setup by saving system configuration information on a USB device and restoring it on one or more computers. ● Execute self-tests on a specified ATA hard drive (when supported by drive). ● Enable or disable DriveLock security (when supported by drive).
Computer Setup—File NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration.
Computer Setup—Storage NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 3-3 Computer Setup—Storage Option Description Device Configuration Lists all installed BIOS-controlled storage devices. When a device is selected, detailed information and options are displayed. The following options may be presented: CD-ROM: Size, model, firmware version, serial number, connector color (not included for USB CD-ROM).
Table 3-3 Computer Setup—Storage (continued) Storage Options eSATA Port (some models) Allows you to set a SATA port as an eSATA port for use with an external drive. Default is enabled. This setting affects only the port with the black connector, labeled as eSATA on the system board. This port should have the eSATA back panel connector attached to use eSATA drives. For more information, see the eSATA white paper at www.hp.com.
Table 3-3 Computer Setup—Storage (continued) DPS Self-Test Allows you to execute self-tests on ATA hard drives capable of performing the Drive Protection System (DPS) self-tests. NOTE: This selection will only appear when at least one drive capable of performing the DPS self-tests is attached to the system.
Table 3-4 Computer Setup—Security (continued) Power-On Password Allows you to set and enable a power-on password. The power-on password prompt appears after a power cycle. If the user does not enter the correct power-on password, the unit will not boot. NOTE: This selection will only appear when at least one drive that supports the DriveLock feature is attached to the system. See the Desktop Management Guide for more information.
Table 3-4 Computer Setup—Security (continued) USB Security Allows you to set Enabled/Disabled (default is Enabled) for: ● ● ● Front USB Ports ◦ USB Port 1 ◦ USB Port 2 ◦ USB Port 3 ◦ USB Port 4 Rear USB Ports ◦ USB Port 1 ◦ USB Port 2 ◦ USB Port 3 ◦ USB Port 4 ◦ USB Port 5 ◦ USB Port 6 Accessory USB Ports ◦ USB Port 1 ◦ USB Port 2 (some models) ◦ USB Port 3 (some models) ◦ USB Port 4 (some models) Slot Security Allows you to disable any PCI or PCI Express slot.
Table 3-4 Computer Setup—Security (continued) System Security (some models: these options are hardware dependent) Data Execution Prevention (enable/disable) - Helps prevent operating system security breaches. Default is enabled. Virtualization Technology (VTx)(some models) (enable/disable) - Controls the virtualization features of the processor. Changing this setting requires turning the computer off and then back on. Default is disabled.
Computer Setup—Power NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 3-5 Computer Setup—Power Option Description OS Power Management ● Runtime Power Management— Enable/Disable. Allows certain operating systems to reduce processor voltage and frequency when the current software load does not require the full capabilities of the processor. Default is enabled. ● Idle Power Savings—Extended/Normal.
Computer Setup—Advanced NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 3-6 Computer Setup—Advanced (for advanced users) Option Heading Power-On Options Allows you to set: ● POST mode (QuickBoot, Clear Memory, FullBoot, or FullBoot Every x Days). ◦ QuickBoot (default) = Do not clear memory or perform a memory test. ◦ FullBoot = Memory test (count) on cold boot. Clears memory on all boots. ◦ Clear Memory = No memory count on cold boot.
Table 3-6 Computer Setup—Advanced (for advanced users) (continued) Bus Options Device Options On some models, allows you to enable or disable: ● PCI SERR# Generation. Default is enabled. ● PCI VGA Palette Snooping, which sets the VGA palette snooping bit in PCI configuration space; only needed when more than one graphics controller is installed. Default is disabled. Allows you to set: ● Turbo Mode (enable/disable).
Recovering the Configuration Settings This method of recovery requires that you first perform the Save to Removable Media command with the Computer Setup (F10) Utility before Restore is needed. (See Save to Removable Media on page 18 in the Computer Setup—File table.) NOTE: It is recommended that you save any modified computer configuration settings to a USB flash media device and save the device for possible future use.
4 Routine Care, SATA Drive Guidelines, and Disassembly Preparation This chapter provides general service information for the computer. Adherence to the procedures and precautions described in this chapter is essential for proper service. CAUTION: When the computer is plugged into an AC power source, voltage is always applied to the system board. You must disconnect the power cord from the power source before opening the computer to prevent system board or component damage.
Removing DIPs from vinyl tray 2,000 V 4,000 V 11,500 V Removing DIPs from Styrofoam 3,500 V 5,000 V 14,500 V Removing bubble pack from PCB 7,000 V 20,000 V 26,500 V Packing PCBs in foam-lined box 5,000 V 11,000 V 21,000 V These are then multi-packaged inside plastic tubes, trays, or Styrofoam. NOTE: 700 volts can degrade a product. Preventing Electrostatic Damage to Equipment Many electronic components are sensitive to ESD.
Grounding the Work Area To prevent static damage at the work area, use the following precautions: ● Cover the work surface with approved static-dissipative material. Provide a wrist strap connected to the work surface and properly grounded tools and equipment. ● Use static-dissipative mats, foot straps, or air ionizers to give added protection. ● Handle electrostatic sensitive components, parts, and assemblies by the case or PCB laminate. Handle them only at static-free work areas.
Operating Guidelines To prevent overheating and to help prolong the life of the computer: ● Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold. ● Operate the computer on a sturdy, level surface. Leave a 10.2-cm (4-inch) clearance on all vented sides of the computer and above the monitor to permit the required airflow. ● Never restrict the airflow into the computer by blocking any vents or air intakes.
To clean the computer case, follow the procedures described below: ● To remove light stains or dirt, use plain water with a clean, lint-free cloth or swab. ● For stronger stains, use a mild dishwashing liquid diluted with water. Rinse well by wiping it with a cloth or swab dampened with clear water. ● For stubborn stains, use isopropyl (rubbing) alcohol. No rinsing is needed as the alcohol will evaporate quickly and not leave a residue.
Cleaning the Mouse Before cleaning the mouse, ensure that the power to the computer is turned off. ● Clean the mouse ball by first removing the retaining plate and the ball from the housing. Pull out any debris from the ball socket and wipe the ball with a clean, dry cloth before reassembly. ● To clean the mouse body, follow the procedures in Cleaning the Computer Case on page 32.
Cables and Connectors Most cables used throughout the unit are flat, flexible cables. These cables must be handled with care to avoid damage. Apply only the tension required to seat or unseat the cables during insertion or removal from the connector. Handle cables by the connector whenever possible. In all cases, avoid bending or twisting the cables, and ensure that the cables are routed in such a way that they cannot be caught or snagged by parts being removed or replaced.
SATA Hard Drives Serial ATA Hard Drive Characteristics Number of pins/conductors in data cable 7/7 Number of pins in power cable 15 Maximum data cable length 39.37 in (100 cm) Data interface voltage differential 400-700 mV Drive voltages 3.3 V, 5 V, 12 V Jumpers for configuring drive N/A Data transfer rate 3.0 Gb/s SATA Hard Drive Cables SATA Data Cable Always use an HP approved SATA 3.0 Gb/s cable as it is fully backwards compatible with the SATA 1.5 Gb/s drives.
● Some flat ribbon cables come prefolded. Never change the folds on these cables. ● Do not bend any cable sharply. A sharp bend can break the internal wires. ● Never bend a SATA data cable tighter than a 30 mm (1.18 in) radius. ● Never crease a SATA data cable. ● Do not rely on components like the drive cage, power supply, or computer cover to push cables down into the chassis. Always position the cables to lay properly by themselves.
5 Removal and Replacement Procedures Adherence to the procedures and precautions described in this chapter is essential for proper service. After completing all necessary removal and replacement procedures, run the Diagnostics utility to verify that all components operate properly. NOTE: Not all features listed in this guide are available on all computers. Preparation for Disassembly See Routine Care, SATA Drive Guidelines, and Disassembly Preparation on page 29 for initial safety procedures. 1.
Access Panel 1. Prepare the computer for disassembly (Preparation for Disassembly on page 38). 2. If the computer is on a stand, remove the computer from the stand. 3. Lift up on the access panel handle (1) then lift the access panel off the computer (2). Figure 5-1 Removing the access panel To install the access panel, reverse the removal procedure.
Front Bezel 1. Prepare the computer for disassembly (Preparation for Disassembly on page 38). 2. Remove the access panel (Access Panel on page 39). 3. Lift up the three tabs on the side of the bezel (1), then rotate the bezel off the chassis (2). Figure 5-2 Removing the front bezel To install the front bezel, reverse the removal procedure.
Bezel Blanks On some models, there are bezel blanks covering the 3.5-inch and 5.25-inch external drive bays that need to be removed before installing a drive. To remove a bezel blank: 1. Remove the access panel (Access Panel on page 39). 2. Remove the front bezel (Front Bezel on page 40).. 3. To remove a bezel blank, push the two retaining tabs that hold the bezel blank in place towards the outer right edge of the bezel (1) and slide the bezel blank back and to the right to remove it (2).
For proper system operation, the DDR3-SDRAM DIMMs must be: ● industry-standard 240-pin ● unbuffered non-ECC PC3-8500 DDR3-1066 MHz-compliant or PC3-10600 DDR3-1333 MHzcompliant ● 1.
Installing DIMMs CAUTION: You must disconnect the power cord and wait approximately 30 seconds for the power to drain before adding or removing memory modules. Regardless of the power-on state, voltage is always supplied to the memory modules as long as the computer is plugged into an active AC outlet. Adding or removing memory modules while voltage is present may cause irreparable damage to the memory modules or system board. The memory module sockets have gold-plated metal contacts.
5. Push the module down into the socket, ensuring that the module is fully inserted and properly seated. Make sure the latches are in the closed position (3). 6. Repeat steps 4 and 5 to install any additional modules. 7. Replace the access panel. 8. If the computer was on a stand, replace the stand. 9. Reconnect the power cord and turn on the computer. 10. Lock any security devices that were disengaged when the access panel was removed.
5. Before installing an expansion card, remove the expansion slot cover or the existing expansion card. NOTE: Before removing an installed expansion card, disconnect any cables that may be attached to the expansion card. a. If you are installing an expansion card in a vacant socket, remove the appropriate expansion slot cover on the back of the chassis. Pull the slot cover straight up then away from the inside of the chassis. Figure 5-6 Removing an expansion slot cover b.
c. If you are removing a PCI Express x16 card, pull the retention arm on the back of the expansion socket away from the card and carefully rock the card back and forth until the connectors pull free from the socket. Pull the expansion card straight up from the socket then away from the inside of the chassis to release it from the chassis frame. Be sure not to scrape the card against the other components. Figure 5-8 Removing a PCI Express x16 expansion card 6.
8. To install a new expansion card, hold the card just above the expansion socket on the system board then move the card toward the rear of the chassis (1) so that the bracket on the card is aligned with the open slot on the rear of the chassis. Press the card straight down into the expansion socket on the system board (2). Figure 5-9 Installing an expansion card NOTE: When installing an expansion card, press firmly on the card so that the whole connector seats properly in the expansion card slot. 9.
14. Lock any security devices that were disengaged when the access panel was removed. 15. Reconfigure the computer, if necessary. System Board Connections Refer to the following illustration and table to identify the system board connectors for your model. Figure 5-11 System board connections Table 5-1 System board connections 48 No.
Table 5-1 System board connections (continued) No. System Board Connector System Board Label Color Component 15 USB MEDIA2 black USB Device, such as a Media Card Reader 16 Hood Sensor HSENSE white Hood Sensor 17 PCI Express x1 X1PCIEXP1 black Expansion Card 18 PCI Express x1 X4PCIEXP black Expansion Card 19 PCI Express x16 X16PCIEXP black Expansion Card 20 PCI PCI white Expansion Card Drives Drive Positions Figure 5-12 Drive positions Table 5-2 Drive Positions 1 3.
Installing and Removing Drives When installing drives, follow these guidelines: ● The primary Serial ATA (SATA) hard drive must be connected to the dark blue primary SATA connector on the system board labeled SATA0. If you are adding a second hard drive, connect it to the white connector on the system board labeled SATA1. ● Connect a SATA optical drive to the white SATA connector on the system board labeled SATA2.
CAUTION: To prevent loss of work and damage to the computer or drive: If you are inserting or removing a drive, shut down the operating system properly, turn off the computer, and unplug the power cord. Do not remove a drive while the computer is on or in standby mode. Before handling a drive, ensure that you are discharged of static electricity. While handling a drive, avoid touching the connector.
6. Press down on the green drive retainer button located on the left side of the drive to disengage the drive from the drive cage (1). While pressing the drive retainer button, slide the drive back until it stops, then lift it up and out of the drive cage (2). Figure 5-14 Removing the 5.25-inch Drive Installing a 5.25-inch Drive into a Drive Bay 1. Prepare the computer for disassembly (Preparation for Disassembly on page 38). 2. Remove the access panel (Access Panel on page 39). 3.
5. Position the guide screws on the drive into the J-slots in the drive bay. Then slide the drive toward the front of the computer until it locks into place. Figure 5-16 Installing the Optical Drive 6. Rotate the drive cage to its upright position. 7. Connect the SATA data cable to the white SATA system board connector labeled SATA2. 8. Route the data cable through the cable guides.
The 3.5-inch drive is located underneath the 5.25-inch drive. You must remove the 5.25-inch drive before removing the 3.5-inch drive. 1. Follow the procedure in Removing a 5.25-inch Drive from a Drive Bay on page 51 to remove the 5.25-inch drive and access the 3.5-inch drive. CAUTION: Ensure that the computer is turned off and that the power cord is disconnected from the electrical outlet before proceeding. 2.
Installing a 3.5-inch Drive into a Drive Bay The 3.5-inch bay is located underneath the 5.25-inch drive. To install a drive into the 3.5-inch bay: NOTE: Install guide screws to ensure the drive will line up correctly in the drive cage and lock in place. HP has provided extra guide screws for the drive bays (four 6-32 standard screws and four M3 metric screws), installed in the front of the chassis, under the front bezel. A secondary hard drive uses 6-32 standard screws.
b. If installing a media card reader, connect the USB cable from the media card reader to the USB connector on the system board labeled MEDIA. Figure 5-21 Connecting the Media Card Reader USB Cable NOTE: Refer to System Board Connections on page 48 for an illustration of the system board drive connectors. 6. Replace the 5.25-inch drive. 7. Replace the front bezel (if removed) and access panel. 8. If the computer was on a stand, replace the stand. 9.
4. Rotate the power supply to its upright position. The hard drive is located beneath the power supply. Figure 5-22 Raising the Power Supply 5. Disconnect the power cable and data cable from the back of the hard drive. 6. Press down on the green release latch next to the hard drive (1). While holding the latch down, slide the drive forward until it stops, then lift the drive up and out of the bay (2).
7. To install a hard drive, you must transfer the silver and blue isolation mounting guide screws from the old hard drive to the new hard drive. Figure 5-24 Installing Hard Drive Guide Screws 8. Align the guide screws with the slots on the chassis drive cage, press the hard drive down into the bay, then slide it back until it stops and locks in place. Figure 5-25 Installing the Hard Drive 9. Connect the power cable and data cable to the back of the hard drive.
Fan duct The fan duct sits between the front fan and the heat sink. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 38). 2. Remove the access panel (Access Panel on page 39). 3. Lift the fan duct straight up out of the chassis. Figure 5-26 Removing the fan duct To install the fan duct, reverse the removal procedure.
Front Fan Assembly The front fan assembly is attached to the front of the chassis. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 38). 2. Remove the access panel (Access Panel on page 39). 3. Remove the front bezel (Front Bezel on page 40). 4. Remove the baffle (Fan duct on page 59). 5. Disconnect the fan cable from the red/brown system board connector labeled CHFAN1. Figure 5-27 Disconnecting the front fan cable 6.
7. Pull the assembly toward the rear of the unit (2), and then lift it out of the chassis. Figure 5-28 Removing the front fan To install the front fan, reverse the removal procedure. Be sure to orient the air flow into the unit.
Hood Sensor The hood sensor is attached in a slot in the rear of the chassis. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 38). 2. Remove the access panel (Access Panel on page 39). 3. Unplug the sensor cable from the system board connector labeled HSENSE (1). 4. Slide the hood sensor straight out of the notch in the chassis (2). NOTE: A flat blade screwdriver can be used to push the hood sensor out of the slot.
Front I/O, Power Switch Assembly The front I/O and power switch/LEDs is one assembly, attached to the front of the chassis. Push the assembly into the chassis to remove. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 38). 2. Remove the access panel (Access Panel on page 39). 3. Remove the front bezel (Front Bezel on page 40). 4. Remove the chassis fan (Front Fan Assembly on page 60). 5. Rotate the drive cage to its upright position. 6.
8. Route the cables through the slots beneath the drive cage, rotate the assembly into the chassis (2), and then remove the assembly from the computer. Figure 5-31 Removing the front I/O, power switch/LED assembly screw To install the front I/O and power switch assembly, reverse the removal procedure. NOTE: Be sure to correctly route the cables beneath the drive cage when reinstalling the assembly. Proper cable routing prevents damage to the cables and allows the drive cage to close properly.
Speaker The speaker is attached to the front of the chassis under the rotating drive cage. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 38). 2. Remove the access panel (Access Panel on page 39). 3. Remove the front bezel (Front Bezel on page 40). 4. Rotate the drive cage to its upright position. 5. Disconnect the speaker wire from the system board labeled SPKR (1). 6. Remove the screw that secures the speaker to the chassis (2). 7.
Heat sink The heat sink is secured atop the processor with four captive Torx screws. The heat sink does not include a fan. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 38). 2. Remove the access panel (Access Panel on page 39). 3. Remove the fan duct (Fan duct on page 59). 4. Remove the front fan (Front Fan Assembly on page 60). 5. In the order shown, loosen the four captive screws that secure the heat sink to the system board tray.
6. After loosening the screws (1), lift the heat sink from atop the processor (2) and set it on its side to keep from contaminating the work area with thermal grease. Figure 5-34 Removing the heat sink When reinstalling the heat sink, make sure that its bottom has been cleaned with an alcohol wipe and fresh thermal grease has been applied to the top of the processor.
Processor 1. Prepare the computer for disassembly (Preparation for Disassembly on page 38). 2. Remove the access panel (Access Panel on page 39). 3. Remove the fan duct (Fan duct on page 59). 4. Remove the front fan assembly (Front Fan Assembly on page 60). 5. Remove the heat sink (Heat sink on page 66). 6. Rotate the locking lever to its full open position (1). 7. Raise and rotate the microprocessor retainer to its fully open position (2). 8. Carefully lift the processor from the socket (3).
2. Secure the locking lever. If reusing the existing heat sink, go to step 3. If using a new heat sink, go to step 6. Figure 5-36 Removing the processor 3. If reusing the existing heat sink, clean the bottom of the heat sink with the alcohol pad provided in the spares kit. CAUTION: Before reinstalling the heat sink you must clean the top of the processor and the bottom of the heat sink with an alcohol pad supplied in the spares kit.
Power Supply WARNING! To reduce potential safety issues, only the power supply provided with the computer, a replacement power supply provided by HP, or a power supply purchased as an accessory from HP should be used with the computer. The rotating power supply is located at the rear of the chassis. It is held in place by a bracket – no screws are used. WARNING! Voltage is always present on the system board when the computer is plugged into an active AC outlet.
To install the power supply, reverse the removal procedure. CAUTION: When installing the power supply cables, make sure they are properly positioned so they are not cut by the drive cage and are not pinched by the rotating power supply. System Board 1. Prepare the computer for disassembly (Preparation for Disassembly on page 38). 2. Remove the access panel (Access Panel on page 39). 3.
11. Lift up the front of the system board, and then pull the system board forward, up, and out of the chassis (2). Figure 5-38 Removing the system board To install the system board, reverse the removal procedure. NOTE: BIOS. When replacing the system board, you must also change the chassis serial number in the CAUTION: Before reinstalling the heat sink you must clean the top of the processor and the bottom of the heat sink with an alcohol pad supplied in the spares kit.
CAUTION: Before replacing the battery, it is important to back up the computer CMOS settings. When the battery is removed or replaced, the CMOS settings will be cleared. Refer to the Computer Setup (F10) Utility Guide for information on backing up the CMOS settings. NOTE: HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, go to http://www.hp.com/ recycle.
2. To insert the new battery, slide one edge of the replacement battery under the holder’s lip with the positive side up (2). Push the other edge down until the clamp snaps over the other edge of the battery. Figure 5-40 Removing the battery from a type 2 holder 3. Replace the computer access panel. 4. Plug in the computer and turn on power to the computer. 5. Reset the date and time, your passwords, and any special system setups, using Computer Setup.
4. Plug in the computer and turn on power to the computer. 5. Reset the date and time, your passwords, and any special system setups, using Computer Setup. Refer to Computer Setup (F10) Utility on page 16. Using the Small Form Factor Computer in a Tower Orientation The Small Form Factor computer can be used in a tower orientation. The HP logo plate on the front bezel is adjustable for either desktop or tower orientation. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 38).
A Connector Pin Assignments This appendix contains the pin assignments for computer connectors. Some of these connectors may not be used on the product being serviced.
Ethernet RJ-45 Connector and Icon Pin Signal 1 (+) Transmit Data 2 (-) Transmit Data 3 (+) Receive Data 4 Unused 5 Unused 6 (-) Receive Data 7 Unused 8 Unused Serial Interface, Powered and Non-Powered Connector and Icon Pin Signal 1 Carrier Detect (12V if powered) 2 Receive Data 3 Transmit Data 4 Data Terminal Ready 5 Signal Ground 6 Data Set Ready 7 Request to Send 8 Clear to Send 9 Ring Indicator (5V if powered) Pin Signal 1 +5 VDC 2 - Data 3 + Data 4 Groun
Microphone Connector and Icon (1/8” miniphone) 1 2 3 Pin Signal 1 (Tip) Audio_left 2 (Ring) Audio_Right 3 (Shield) Ground Pin Signal 1 (Tip) Audio_left 2 (Ring) Power_Right 3 (Shield) Ground Pin Signal 1 (Tip) Audio_In_Left 2 (Ring) Audio_In_Right 3 (Shield) Ground Pin Signal 1 (Tip) Audio_Out_Left 2 (Ring) Audio_Out_Right 3 (Shield) Ground Headphone Connector and Icon (1/8” miniphone) 1 2 3 Line-in Audio Connector and Icon (1/8” miniphone) 1 2 3 Line-out Audio Connecto
Monitor Connector and Icon Pin Signal Pin Signal 1 Red Analog 9 +5V (fused) 2 Green Analog 10 Ground 3 Blue Analog 11 Not used 4 Not used 12 DDC Serial Data 5 Ground 13 Horizontal Sync 6 Ground 14 Vertical Sync 7 Ground 15 DDC Serial Clock 8 Ground 4-Pin Power (for CPU) Connector and Icon Pin Signal 1 GND 2 GND 3 +12V CPU 4 -12V CPU Monitor 79
SATA Data and Power Drive Connector Pin Signal Pin Signal Pin Signal Pin Signal S1 Ground S2 A+ S3 A- S4 Ground S5 B- S6 B+ S7 Ground P1 Ground P2 V 3.3 P3 V 3.
PCI Express x1, x4, x8, and x16 PCI Express Connector Pin A Pin Signal Pin Signal Pin Signal Pin Signal Pin Signal 1 PRSNT1 6 JTAG3 11 PERST# 16 PERp0 21 PERp1 2 +12V 7 JTAG4 12 GND 17 PERn0 22 PERn1 3 +12V 8 JTAG5 13 REFCLK+ 18 GND 23 GND 4 GND 9 +3.3V 14 REFCLK- 19 RSVD 24 GND 5 JTAG2 10 +3.
PCI Express x1, x4, x8, and x16 PCI Express Connector Pin B Pin Signal Pin Signal Pin Signal Pin Signal Pin Signal 1 +12V 6 SMDAT 11 WAKE# 16 GND 21 GND 2 +12V 7 GND 12 RSVD 17 22 GND 23 PETp2 24 PETn2 25 GND GND 3 RSVD 8 +3.3 V 13 GND 18 PETp1 4 GND 9 JTAG1 14 PETp0 19 PETn1 5 SMCLK 10 3.
DVI Connector Connector and Icon Pin Signal Pin Signal 1 T.M.D.S. Data2– 13 T.M.D.S. Data3+ 2 T.M.D.S. Data2+ 14 +5V Power 3 T.M.D.S. Data2/4 Shield 15 Ground (for +5V) 4 T.M.D.S. Data4– 16 Hot Pug Detect 5 T.M.D.S. Data4+ 17 T.M.D.S. Data0– 6 DDC Clock 18 T.M.D.S. Data0+ 7 DDC Data 19 T.M.D.S. Data0/5 Shield 8 No Connect 20 T.M.D.S. Data5– 9 T.M.D.S. Data1– 21 T.M.D.S. Data5+ 10 T.M.D.S. Data1+ 22 T.M.D.S. Data Shield 11 T.M.D.S. Data1/3 Shield 23 T.M.D.S.
DisplayPort Connector Connector and Icon 84 Pin Signal Pin Signal 1 ML_Lane 0 (p) 13 CONFIG1 2 Ground 14 CONFIG2 3 ML_Lane 0 (n) 15 AUX CH (p) 4 ML_Lane 1 (p) 16 Ground 5 Ground 17 AUX CH (n) 6 ML_Lane 1 (n) 18 Hot Plug 7 ML_Lane 2 (p) 19 Return 8 Ground 20 DP_PWR 9 ML_Lane 2 (n) 10 ML_Lane 3 (p) 11 Ground 12 ML_Lane 3 (n) Appendix A Connector Pin Assignments
B Power Cord Set Requirements The power supplies on some computers have external power switches. The voltage select switch feature on the computer permits it to operate from any line voltage between 100-120 or 220-240 volts AC. Power supplies on those computers that do not have external power switches are equipped with internal switches that sense the incoming voltage and automatically switch to the proper voltage.
Country-Specific Requirements Additional requirements specific to a country are shown in parentheses and explained below. 86 Country Accrediting Agency Country Accrediting Agency Australia (1) EANSW Italy (1) IMQ Austria (1) OVE Japan (3) METI Belgium (1) CEBC Norway (1) NEMKO Canada (2) CSA Sweden (1) SEMKO Denmark (1) DEMKO Switzerland (1) SEV Finland (1) SETI United Kingdom (1) BSI France (1) UTE United States (2) UL Germany (1) VDE 1.
C POST Error Messages This appendix lists the error codes, error messages, and the various indicator light and audible sequences that you may encounter during Power-On Self-Test (POST) or computer restart, the probable source of the problem, and steps you can take to resolve the error condition. POST Message Disabled suppresses most system messages during POST, such as memory count and non-error text messages. If a POST error occurs, the screen will display the error message.
POST Numeric Codes and Text Messages This section covers those POST errors that have numeric codes associated with them. The section also includes some text messages that may be encountered during POST. NOTE: The computer will beep once after a POST text message is displayed on the screen. Table C-1 Numeric Codes and Text Messages Control panel message Description Recommended action 101-Option ROM Checksum Error System ROM or expansion board option ROM checksum. 1. Verify the correct ROM. 2.
Table C-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action 163-Time & Date Not Set Invalid time or date in configuration memory. RTC (real-time clock) battery may need to be replaced. Reset the date and time under Control Panel (Computer Setup can also be used). If the problem persists, replace the RTC battery.
Table C-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action 303-Keyboard Controller Error I/O board keyboard controller. 1. Reconnect keyboard with computer turned off. 2. Replace the system board. 1. Reconnect the keyboard with computer turned off. 2. Ensure that none of the keys are depressed. 3. Replace the keyboard. 4. Replace the system board. 1. Reseat the graphics card (if applicable). 2. Clear CMOS.
Table C-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action 601-Diskette Controller Error Diskette controller circuitry or floppy drive circuitry incorrect. 1. Check and/or replace cables. 2. Clear CMOS. (See Appendix B, Password Security and Resetting CMOS on page 100.) 3. Replace diskette drive. 4. Replace the system board. 1. Disconnect any other diskette controller devices (tape drives). 2. Clear CMOS.
Table C-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action 1720-SMART Hard Drive Detects Imminent Failure Hard drive is about to fail. (Some hard drives have a hard drive firmware patch that will fix an erroneous error message.) 1. Determine if hard drive is giving correct error message. Enter Computer Setup and run the Drive Protection System test under Storage > DPS Self-test. 2. Apply hard drive firmware patch if applicable.
Table C-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action 2201-MEBx Module did not checksum correctly Memory error during POST execution of the Management Engine (ME) BIOS Extensions option ROM. 1. Reboot the computer. 2. Unplug the power cord, re-seat the memory modules, and reboot the computer. 3. If the memory configuration was recently changed, unplug the power cord, restore the original memory configuration, and reboot the computer. 4.
Table C-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action 2211-Memory not configured correctly for proper MEBx execution. DIMM1 or XMM1 is not installed. Make sure there is a memory module in the black DIMM1 socket and that it is properly seated. 2212-USB Key Provisioning failure writing to device USB device used for USB key provisioning will not allow BIOS to update provision file properly. 1. Try a different USB key device for provisioning. 2.
Table C-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action 2230-General error during MEBx execution Error occurred during MEBx execution which fails into the “General” grouping. Status information displayed along with the error provides further clarity into the failure. MEBx handles transference of information between the system BIOS and ME firmware. 1. Reboot the computer. 2.
Table C-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action Network Server Mode Active and No Keyboard Attached Keyboard failure while Network Server Mode enabled. 1. Reconnect keyboard with computer turned off. 2. Check connector for bent or missing pins. 3. Ensure that none of the keys are depressed. 4. Replace keyboard. Parity Check 2 Parity RAM failure. Run Computer Setup and Diagnostic utilities.
Table C-2 Diagnostic Front Panel LEDs and Audible Codes (continued) Activity Beeps Possible Cause Recommended Action Red Power LED flashes two times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. 2 Processor thermal protection activated: 1. Ensure that the computer air vents are not blocked and the processor cooling fan is running. 2. Open hood, press power button, and see if the processor fan spins.
Table C-2 Diagnostic Front Panel LEDs and Audible Codes (continued) Activity Beeps Possible Cause Recommended Action Red Power LED flashes five times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. 5 Pre-video memory error. CAUTION: To avoid damage to the DIMMs or the system board, you must unplug the computer power cord before attempting to reseat, install, or remove a DIMM module.
Table C-2 Diagnostic Front Panel LEDs and Audible Codes (continued) Activity Beeps Possible Cause Recommended Action Red Power LED flashes ten times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. 10 Bad option card. 1. Check each option card by removing the card (one at a time if multiple cards), then power on the system to see if fault goes away. 2.
D Password Security and Resetting CMOS This computer supports security password features, which can be established through the Computer Setup Utilities menu. This computer supports two security password features that are established through the Computer Setup Utilities menu: setup password and power-on password. When you establish only a setup password, any user can access all the information on the computer except Computer Setup.
Resetting the Password Jumper To disable the power-on or setup password features, or to clear the power-on or setup passwords, complete the following steps: 1. Shut down the operating system properly, then turn off the computer and any external devices, and disconnect the power cord from the power outlet. 2. With the power cord disconnected, press the power button again to drain the system of any residual power.
Clearing and Resetting the CMOS The computer’s configuration memory (CMOS) stores information about the computer’s configuration. The CMOS button resets CMOS but does not clear the power-on and setup passwords. Clearing CMOS will clear the Active Management Technology (AMT) settings in the Management Engine BIOS Extension (MEBx), including the password. The password will default to “admin” and will need to be reset. The AMT settings will also need to be reset. To access the MEBx, press Ctrl+P during POST.
4. Locate, press, and hold the CMOS button in for five seconds. NOTE: Make sure you have disconnected the AC power cord from the wall outlet. The CMOS button will not clear CMOS if the power cord is connected. Figure D-1 CMOS button NOTE: For assistance locating the CMOS button and other system board components, see the Illustrated Parts & Service Map (IPSM). 5. Replace the computer cover or access panel. 6. Reconnect the external devices. 7. Plug in the computer and turn on power.
E Drive Protection System (DPS) The Drive Protection System (DPS) is a diagnostic tool built into the hard drives installed in some computers. DPS is designed to help diagnose problems that might result in unwarranted hard drive replacement. When these systems are built, each installed hard drive is tested using DPS, and a permanent record of key information is written onto the drive. Each time DPS is run, test results are written to the hard drive.
Accessing DPS Through Computer Setup When the computer does not power on properly you should use Computer Setup to access the DPS program. To access DPS, perform the following steps: 1. Turn on or restart the computer. 2. When the F10 Setup message appears in the lower-right corner of the screen, press the F10 key. NOTE: If you do not press the F10 key while the message is displayed, you must turn the computer off, then on again, to access the utility.
F Specifications ms6200 Table F-1 Specifications Chassis (in the desktop position) Height 4.0 in 10.0 cm Width 13.3 in 33.8 cm Depth 14.9 in 37.9 cm Approximate Weight 16.7 lb 7.6 kg Weight Supported (maximum distributed load in desktop position) 77 lb 35 kg Operating 50° to 95°F 10° to 35°C Nonoperating -22° to 140°F -30° to 60°C Temperature Range NOTE: Operating temperature is derated 1.0° C per 300 m (1000 ft) to 3000 m (10,000 ft) above sea level; no direct sustained sunlight.
Table F-1 Specifications (continued) Rated Input Current 1 4A This system utilizes an active power factor corrected power supply. This allows the system to pass the CE mark requirements for use in the countries of the European Union. The active power factor corrected power supply also has the added benefit of not requiring an input voltage range select switch. t200 Specifications Table F-2 t200 Zero Client Dimensions Width (side to side) 136 mm 5.35 in. Height (without mounting bracket) 35 mm 1.
Index Symbols/Numerics 4–pin power pin assignments 79 A access panel removal and replacement 39 altitude specifications 107 audible codes 96 B battery disposal 35 removal and replacement 72 beep codes 96 booting options Full Boot 87 Quick Boot 87 C cable management 36 cable pinouts SATA data 36 cautions AC power 29 cables 35 cooling fan 34 electrostatic discharge 29 keyboard cleaning 33 keyboard keys 33 chasis types, illustrated 29 cleaning computer 32 mouse 34 safety precautions 32 CMOS backing up 100 c
I installing drive cables 50 expansion card 44 hard drive 56 media card reader 55 memory 41 optical drive 52 K keyboard cleaning 33 pin assignments 76 L LEDs blinking power 96 blinking PS/2 keyboard 96 line-in audio pin assignments 78 line-out audio pin assignments 78 M media card reader features 3 installation 55 removal 53 memory installation 41 SFF specifications 41 socket population 42 microphone connector ms6200 2 t200 5 microphone pin assignments 78 monitor 5 pin assignments 79 mouse cleaning 34 pin a
Torx T15 screwdriver 34 tower orientation 75 U USB PC power connector location t200 6 USB pin assignments 77 USB ports ms6200 2 t200 5 V ventilation, proper 32 VGA connector location t200 6 W weight 107 110 Index
