HP UPS T1000/1500 User Guide April 2006 (First Edition) Part Number 404317-001a
© Copyright 2006 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Contents Component identification ............................................................................................................... 6 UPS UPS UPS UPS UPS UPS front panel ......................................................................................................................................... 6 front panel controls and LED indicators .................................................................................................. 7 T1000 NA/JPN/TWN rear panel ..................
Site Wiring Fault LED is red ...................................................................................................................... 30 Specifications ............................................................................................................................. 31 T1000 physical specifications ................................................................................................................... 31 T1500 physical specifications .....................................
Index.........................................................................................................................................
Component identification In this section UPS UPS UPS UPS UPS UPS front panel ........................................................................................................................................ 6 front panel controls and LED indicators................................................................................................. 7 T1000 NA/JPN/TWN rear panel .......................................................................................................
UPS front panel controls and LED indicators Item Description Function 1 Power On/Standby button Turns the UPS power on and off, and places the UPS in Standby mode.1 2 Output Load Level LED Shows approximately how much of the UPS power capacity is used to support the equipment connected to the output receptacles. Red—Maximum load Amber—Medium load Green—Light load 3 Power LED Green—The UPS is on and supplying connected equipment with AC power.
Item Description Function 6 Battery Charge LED When the UPS is operating from utility power (the Power LED is green), the Battery Charge LED indicates the approximate charge state of the batteries: Red—The batteries are beginning to charge. Amber—The batteries are midway through charging. Green—The batteries are fully charged.
Item Description 6 Network Transient Protector OUT jack 7 Site Wiring Fault LED 8 Input power cord with NEMA 5-15 plug 9 Eight NEMA 5-15 output receptacles for surge and battery backup protection.
UPS T1000 INTL rear panel Item Description 1 Voltage configuration DIP switches 2 Serial communications port 3 USB communications port 4 Option slot 5 Network Transient Protector IN jack 6 Network Transient Protector OUT jack 7 Input power receptacle (IEC-320-C14) for country-specific plug attachment 8 Eight IEC-320-C13 output receptacles for surge and battery backup protection Component identification 10
UPS T1500 INTL rear panel Item Description 1 Voltage configuration DIP switches 2 Serial communications port 3 USB communications port 4 Option slot 5 Network Transient Protector IN jack 6 Network Transient Protector OUT jack 7 Input circuit breaker 8 Input power receptacle (IEC-320-C14) for country-specific plug attachment 9 Eight IEC-320-C13 output receptacles for surge and battery backup protection Component identification 11
Installation In this section Precautions............................................................................................................................................ 12 Electrical requirements ............................................................................................................................ 12 Checking the battery recharge date.......................................................................................................... 13 Connecting the batteries........
Checking the battery recharge date Before unpacking the UPS, check the date on the battery recharge date label that is affixed to the shipping carton. IMPORTANT: Do not use the battery if the recharge date has passed. If the date on the battery recharge date label has passed without the battery being recharged, contact an HP authorized service representative for directions. Connecting the batteries WARNING: The unit contains sealed lead-acid battery modules.
2. Connect the negative (black) lead to the negative battery terminal. NOTE: A small amount of arcing may occur when connecting the batteries. This is normal and does not damage the unit or present any safety concern. 3. Replace the UPS front bezel. Selecting the UPS voltage configuration Using a small tool, position the DIP switches according to the desired voltage configuration as identified on the rear panel of the UPS and in the following table.
T1000/1500 NA/JPN/TWN T1000/1500 INTL Output voltage Input voltage range DIP switch 2 DIP switch 1 100 V* (JPN/TWN) 90–106 V Down Up 110 V 99–116 V Up Down 120 V* (NA) 108–127 V Down Down 120 V 108-127 V Up Up 220 V 198–233 V Down Up 230 V* (INTL) 207–243 V Up Down 230 V 207-243 V Down Down 240 V 216–254 V Up Up Connecting the host computer CAUTION: Use only the computer interface cable supplied with the UPS to connect the communications port to the host computer.
Connecting the USB communications port CAUTION: Using a USB to serial converter cable will damage the UPS. Connecting the Network Transient Protectors CAUTION: To avoid damaging the equipment, use the Network Transient Protector with a standard telephone line only, not with a digital PBX. To protect equipment against surges over a network data line: 1. Connect the network wall jack to the UPS Network Transient Protector IN jack. 2. Connect the equipment to the UPS Network Transient Protector OUT jack.
Connecting the UPS to utility power WARNING: To prevent injury from electric shock or damage to the equipment: • Plug the input line cord into a grounded (earthed) electrical outlet that is installed near the equipment and is easily accessible. • Do not disable the grounding plug on the input line cord. The grounding plug is an important safety feature. • Do not use extension cords. 1.
Powering up the UPS Press and hold the Power On/Standby button (1) until the UPS beeps. The Power LED illuminates solid green, indicating that power is available at the UPS output receptacles.
UPS operations In this section Initiating a self-test .................................................................................................................................. 19 Silencing an audible alarm...................................................................................................................... 19 Powering down the UPS..........................................................................................................................
4. Wait at least 60 seconds for the UPS internal circuitry to discharge.
Power management In this section HP Power Manager features .................................................................................................................... 21 HP Power Manager features HP Power Manager software ensures maximum power reliability of computer systems through comprehensive control of UPSs. The easy-to-use browser interface enables novice users to configure and manage power protection settings.
Maintenance In this section Updating the UPS firmware ..................................................................................................................... 22 Replacing the batteries............................................................................................................................ 22 Cleaning battery spills ............................................................................................................................
• Minimize the amount of time the UPS uses battery power by matching the UPS configuration with the utility voltage. See "Selecting the UPS voltage configuration (on page 14)." • Keep the area around the UPS clean and dust-free. If the environment is very dusty, clean the outside of the UPS regularly with a vacuum cleaner. • Maintain the ambient temperature at 25°C (77°F).
4. Disconnect the negative (black) lead.
5. Remove the battery module.
6. Disconnect the positive (red) lead. To replace the component, reverse the removal procedure. IMPORTANT: Charge the batteries for at least 24 hours before supplying backup power to devices. The batteries charge to: • 90% of their capacity within 4 hours • 100% of their capacity within 24 hours Cleaning battery spills 1. Put on acid-resistant boots, a chemical face shield, chemical splash goggles, and acid-resistant gloves. WARNING: Battery acid can severely damage your eyes and skin. 2.
4. Neutralize spilled battery acid with the special solutions contained in a spill kit or with a solution of 1 lb baking soda to 1 gallon of water. 5. Be sure the mixture is neutral, then collect the residue and place the residue in a drum or other suitable container. 6. Properly dispose of hazardous waste. WARNING: Do not allow discharge of unneutralized acid to reach the sewer.
Troubleshooting In this section UPS does not start .................................................................................................................................. 28 Audible alarm sounds ............................................................................................................................. 28 UPS operates on battery only...................................................................................................................
UPS frequently switches between utility and battery power Action: 1. Check the input voltage and reconfigure the UPS ("Selecting the UPS voltage configuration" on page 14). 2. Contact a qualified electrician to verify that the utility power is suitable for the UPS. UPS does not provide the expected backup time Action: 1. If the Output Load Level LED is red or flashing red, remove one or more load devices to reduce the power requirements. 2. Power down the UPS ("Powering down the UPS" on page 19). 3.
Output Load Level LED is red or flashing red Action: 1. Remove one or more load devices to reduce the power requirements. 2. Initiate a self-test ("Initiating a self-test" on page 19). 3. If the condition persists, verify that the load devices are not defective. Battery Charge LED is red Action: If the Power LED is flashing green: a. Save your work, and power down the UPS ("Powering down the UPS" on page 19). b.
Specifications In this section T1000 physical specifications.................................................................................................................. 31 T1500 physical specifications.................................................................................................................. 31 UPS input specifications .......................................................................................................................... 31 T1000 output specifications.........
UPS model Utility voltage frequency (Hz) Available settings utility Branch circuit voltage (VAC) rating (A) Line cord T1000/1500 NA/JPN/TWN 60/50 100, 110, 120* 15 Nondetachable power cord with NEMA 5-15 plug T1000/1500 INTL 50/60 220, 230*, 240 10 Detachable power cord with IEC-320 plug T1000 output specifications UPS model Output receptacles Maximum current T1000 NA/JPN/TWN 8 x NEMA 5-15 8.3 A T1000 INTL 8 x IEC-320-C13 4.
Configuration setting (VAC) Available nominal output voltage (VAC) 230 230 240 240 Output tolerance specifications Source of power Regulation Utility power (nominal range) -10% to +6% of nominal output voltage rating (within the guidelines of the Computer Business Equipment Manufacturers Association) Battery power ±5% of nominal output voltage rating Output feature specifications Feature Specification Online efficiency 94% nominal input voltage Voltage wave shape Sine wave; 5% THD with typi
Feature Specification Operating altitude Up to 2,000 m (6,600 ft) above sea level Nonoperating altitude Up to 15,000 m (49,212 ft) above sea level Audible noise Less than 53 dBA Specifications 34
Spares In this section Ordering spares..................................................................................................................................... 35 T1000 UPS spare parts list ...................................................................................................................... 35 T1500 UPS spare parts list ...................................................................................................................... 35 Hardware options ......................
Technical support In this section Before you contact HP............................................................................................................................. 36 HP contact information............................................................................................................................
Warranty information In this section Limited warranty .................................................................................................................................... 37 $250,000 Computer Load Protection Guarantee ....................................................................................... 37 Pre-Failure Battery Warranty ....................................................................................................................
• Notification from power management software Warranty information 38
Regulatory compliance notices In this section Regulatory compliance identification numbers............................................................................................ 39 Federal Communications Commission notice ............................................................................................. 39 Declaration of conformity for products marked with the FCC logo, United States only..................................... 40 Modifications...................................................
Class A equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user’s authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations.
Disposal of waste equipment by users in private households in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
Korean notice Class A equipment Class B equipment Battery replacement notice WARNING: Power products contain sealed lead-acid battery modules. A risk of fire and burns exists if the battery is not properly handled. To reduce the risk of personal injury: • Do not attempt to recharge the battery. • Do not expose the battery to temperatures higher than 60°C (140°F). • Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water. The battery might explode.
Electrostatic discharge In this section Preventing electrostatic discharge............................................................................................................. 44 Grounding methods to prevent electrostatic discharge ................................................................................ 44 Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts.
Acronyms and abbreviations IEC International Electrotechnical Commission LED light-emitting diode NEC National Electrical Code NEMA National Electrical Manufacturers Association PFC power factor corrected UPS uninterruptible power system USB universal serial bus Acronyms and abbreviations 45
Index A D alarm conditions 19 alarms, silencing 19 alarms, troubleshooting 28 authorized reseller 36 devices, connecting 17 diagnostics 19 dimensions, UPS 31 DIP switches, location 8, 9, 10, 11 DIP switches, setting 14 disposal, battery 43 B backup time, insufficient 29 batteries, care and storage 22 batteries, charging 17 batteries, cleaning spills 26 batteries, connecting 13 batteries, replacing 22, 23 batteries, runtime 33 batteries, specifications 33 battery cables, connecting 13 Battery Charge LED,
J R Japanese notice 42 regulatory compliance identification numbers 39 regulatory compliance notices 39, 41, 42 replacing the batteries 22, 23 required information 36 runtime specifications 33 K Korean notices 43 L LED, power button 7 LEDs 6, 7 limited warranty 37 load protection guarantee 37 low-voltage UPS 8, 9 M maintenance 22 models, high-voltage UPS 10, 11 models, low-voltage UPS 8, 9 modifications, FCC notice 41 Mute/Test button 7 N nominal voltage, configuring 14 North America and Japan model
V Voltage Correction LED, location 7 Voltage Correction LED, troubleshooting 29 voltage specifications 32 voltage, configuring 14 W warranties 37 weight, UPS 31 Index 48
