Instruction Manual

ManualsBrandsHP ManualsStorageStoreOnce Backup

100

Table Of Contents

G2 Backup System user guide
Contents
1 Getting started
- Introduction
- What is the Web Management interface?
- To run the Web Management Interface
- Initial logon and Welcome message
2 Home, Summary
- Summary (Home)
3 Virtual Tape Devices
- Devices (Virtual Tape Devices)
- Making Replication Target libraries visible to the host
- Cartridges (Virtual Tape Devices)
4 NAS
- Shares (NAS)
- Configuring NAS targets for CIFS
- Configuring users on AD (CIFS shares only)
- Configuring NAS shares for NFS
5 Appliance Configuration
- Network (Configuration)
- Fibre Channel (Configuration)
- iSCSI (Configuration)
- SNMP (Configuration)
  - HP Systems Insight Manager
- Email Alerts (Configuration)
  - To configure Microsoft Exchange Server
6 Status
- System Activity (Status)
- Storage (Status)
- Disk (Status)
- RAID (Status)
- Network (Status)
- iSCSI (Status)
- Fibre Channel (Status)
- Storage Reporting (Status)
- Log (Status)
7 Replication
- Status (Replication)
- Virtual Tape Mappings (Replication)
  - Running the replication wizard (virtual tape devices)
- NAS Mappings (Replication)
  - Running the replication wizard (NAS)
- Partner Appliances (Replication)
  - Source Appliance Permissions tab
- Local Appliance (Replication)
- Event History (Replication)
8 Administration
- User Account (Administration)
- Security (Administration)
- Date & Time (Administration)
- Housekeeping (Administration)
- Shutdown (Administration)
- Software (Administration)
- Support (Administration)
- Backup & Restore (Administration)
- License (Administration)
9 Restore processes with replication
- Recovering a Source Appliance (Virtual Tape devices)
- Recovering a Source Appliance (NAS shares)
10 Restore processes without replication
- Restore scenarios
- Restoring single files
- Restore and deduplication
- Reconnecting to the to iSCSI VTL devices after host failure
11 Understanding LEDs
- HP D2D4324/4312 Backup System
- HP D2D4112/4106 Backup System
- HP D2D2502/2504 Backup System
- Hot-plug drive LEDs
- Fibre Channel card LEDs
- Capacity upgrade kit LEDs
12 Hardware monitoring
- Resolving problems
13 Troubleshooting
- Connecting to the StoreOnce Backup System from the backup application
- Connecting to the network
- Using the 10Gb ports (HP D2D4300 Series only)
- Performance
- Web Management Interface errors and warnings
- Power On/Off Problems
- Cannot connect to Web Management Interface
- NFS State handle error
- Cannot authenticate an iSCSI session
- Diagnostic Fibre Channel device
- If the HP StoreOnce Backup System runs out of disk space
- Cannot access a storage shelf (HP D2D4100 and 4300 Series Backup Systems)
- If backup or replication fails
- Recovering Devices that have ‘failed to start’ or have become read-only
- StoreOnce Backup System configuration problems
- Upgrade licenses
- Replacement of hardware
- Upgrades to component parts
14 Hard disk replacement
- RAID
- How do I know a disk has failed?
- Replacing a hot-plug hard disk
- After replacing the failed disk
- If several disks fail
A Extra information for G1 products
- Overview
- Major differences
  - VTL devices
  - NAS devices
- Tape Attach
Glossary
About this guide
Index

6. If it is an existing Target Library, adopt the Slot Mapping that had been configured. If the

mapping had been broken and the library has reverted to Non-Replicating, create a new slot

mapping. All slots in the Target Library will be selected by default, but you may deselect any

cartridges that you do not wish to recover to the Source Library.

Click Adopt to run reverse replication.

If the Target Library supports multiple library Fan In, the library may still be a Replication

Target if other mappings exist. You can now recover by adding the mapping back to map

the unmapped slots to the new Source Library.

98 Restore processes with replication