Instruction Manual

ManualsBrandsHP ManualsStorageStoreOnce Backup

Table Of Contents

G2 Backup System user guide
Contents
1 Getting started
- Introduction
- What is the Web Management interface?
- To run the Web Management Interface
- Initial logon and Welcome message
2 Home, Summary
- Summary (Home)
3 Virtual Tape Devices
- Devices (Virtual Tape Devices)
- Making Replication Target libraries visible to the host
- Cartridges (Virtual Tape Devices)
4 NAS
- Shares (NAS)
- Configuring NAS targets for CIFS
- Configuring users on AD (CIFS shares only)
- Configuring NAS shares for NFS
5 Appliance Configuration
- Network (Configuration)
- Fibre Channel (Configuration)
- iSCSI (Configuration)
- SNMP (Configuration)
  - HP Systems Insight Manager
- Email Alerts (Configuration)
  - To configure Microsoft Exchange Server
6 Status
- System Activity (Status)
- Storage (Status)
- Disk (Status)
- RAID (Status)
- Network (Status)
- iSCSI (Status)
- Fibre Channel (Status)
- Storage Reporting (Status)
- Log (Status)
7 Replication
- Status (Replication)
- Virtual Tape Mappings (Replication)
  - Running the replication wizard (virtual tape devices)
- NAS Mappings (Replication)
  - Running the replication wizard (NAS)
- Partner Appliances (Replication)
  - Source Appliance Permissions tab
- Local Appliance (Replication)
- Event History (Replication)
8 Administration
- User Account (Administration)
- Security (Administration)
- Date & Time (Administration)
- Housekeeping (Administration)
- Shutdown (Administration)
- Software (Administration)
- Support (Administration)
- Backup & Restore (Administration)
- License (Administration)
9 Restore processes with replication
- Recovering a Source Appliance (Virtual Tape devices)
- Recovering a Source Appliance (NAS shares)
10 Restore processes without replication
- Restore scenarios
- Restoring single files
- Restore and deduplication
- Reconnecting to the to iSCSI VTL devices after host failure
11 Understanding LEDs
- HP D2D4324/4312 Backup System
- HP D2D4112/4106 Backup System
- HP D2D2502/2504 Backup System
- Hot-plug drive LEDs
- Fibre Channel card LEDs
- Capacity upgrade kit LEDs
12 Hardware monitoring
- Resolving problems
13 Troubleshooting
- Connecting to the StoreOnce Backup System from the backup application
- Connecting to the network
- Using the 10Gb ports (HP D2D4300 Series only)
- Performance
- Web Management Interface errors and warnings
- Power On/Off Problems
- Cannot connect to Web Management Interface
- NFS State handle error
- Cannot authenticate an iSCSI session
- Diagnostic Fibre Channel device
- If the HP StoreOnce Backup System runs out of disk space
- Cannot access a storage shelf (HP D2D4100 and 4300 Series Backup Systems)
- If backup or replication fails
- Recovering Devices that have ‘failed to start’ or have become read-only
- StoreOnce Backup System configuration problems
- Upgrade licenses
- Replacement of hardware
- Upgrades to component parts
14 Hard disk replacement
- RAID
- How do I know a disk has failed?
- Replacing a hot-plug hard disk
- After replacing the failed disk
- If several disks fail
A Extra information for G1 products
- Overview
- Major differences
  - VTL devices
  - NAS devices
- Tape Attach
Glossary
About this guide
Index

enabled. If it is not checked, the times are ignored. Then enter the general value you have

just calculated for the Recommended Limit in each required window manually.

NOTE: All settings are applied to the HP StoreOnce Backup System — you cannot configure

settings for individual jobs. The Bandwidth Limit windows override the General Limit when the

time specified for the window is active. Outside of Bandwidth Limit windows the General Limit

applies.

4. Click Apply.

Blackout windows

This option allows you to specify times when replication should not occur, for example during

planned maintenance or heavy network traffic. You may configure multiple blackout windows.

NOTE: This setting relates to the local appliance in its role as a source or target device. No

replication jobs will be started if the Source or Target Appliance for a mapping is in blackout, and

any running jobs for the mapping will be paused.

1. Select the Blackout Windows tab.

2. Click Edit.

80 Replication