Installation Guide
For example, copy the /11iv3SG_DVD into the same HP-UX depot.
If there are multiple ServiceGuard and StorageManagement DVDs, you must repeat this step
for each DVD.
4. If you plan to use this HP-UX depot to update systems other than the system where the depot
resides, you must register the HP-UX depot. The swcopy command automatically registers the
depot when it is first created. However, HP recommends that you register the depot again
such that it is visible to other systems. Enter the following command to register the HP-UX depot:
# swreg -l depot @ /var/depots/my_hpux_depot
5. On each system that must be updated to HP–UX 11i v3, enter the following command:
# update-ux -s depot_server_name:/var/depots/my_hpux_depot \
!Base-VxVM-50 B3929HB \
B9116EB Base-VxFS-51 Base-VxTools-51 Base-VxVM-51 VxFS-SDK-51
If the HP-UX depot resides on the system that must be updated, you need not specify the name
of the depot server using the depot_server_name option. The depot_server_name
option indicates the hostname of the system where the my_hpux_depot resides followed
by a colon (:).
This command updates the system to HP-UX 11i v3 and VxVM 5.1 SP1 and VxFS 5.1 SP1.
The !Base-VxVM-50 entries on the command line ensure that VxVM 5.0 is not installed from
the depot during the update.
When you update HP-UX 11i v2 systems that include VxVM 3.5, the following message is displayed:
WARNING: The following was found while selecting software:
- There are new revisions of SW available in the source that would
update SW already installed on the system. The newer revisions are
not selected for installation. This will leave the incompatible old
revision of SW on the system. The affected SW is:
- VRTSfspro.FSPRO-PRG,r=4.1x replaces
VRTSfspro.FSPRO-PRG,r=3.5_2_ga08.006
- VRTSfspro,r=4.1x replaces VRTSfspro,r=3.5_2_ga08.006
- VRTSob.VEAS-FILESET,r=3.2.555.1 replaces
VRTSob.VEAS-FILESET,r=3.2.532.0.001
- VRTSob,r=3.2.555.1 replaces VRTSob,r=3.2.532.0.001
- VRTSobgui.VEA-FILESET,r=3.2.555.1 replaces
VRTSobgui.VEA-FILESET,r=3.2.532.0.001
- VRTSobgui,r=3.2.555.1 replaces VRTSobgui,r=3.2.532.0.001
- VRTSvlic.VLIC-RUN,r=3.02.23.1 replaces
VRTSvlic.VLIC-RUN,r=3.01.IA.002.010
- VRTSvlic,r=3.02.23.1 replaces VRTSvlic,r=3.01.IA.002.010
- VRTSvmdoc.VXVM-DOC,r=4.1.032 replaces
VRTSvmdoc.VXVM-DOC,r=3.5~IA.014
- VRTSvmdoc,r=4.1.032 replaces VRTSvmdoc,r=3.5~IA.014
- VRTSvmpro.VMPRO-PRG,r=4.1.020 replaces
VRTSvmpro.VMPRO-PRG,r=3.5~IA.014
- VRTSvmpro,r=4.1.020 replaces VRTSvmpro,r=3.5~IA.014
- VRTSvxvm.VXMS,r=4.1.032 replaces VRTSvxvm.VXMS,r=3.5~IA.014
- VRTSvxvm.VXVM-ENG-A-MAN,r=4.1.032 replaces
VRTSvxvm.VXVM-ENG-A-MAN,r=3.5~IA.014
- VRTSvxvm.VXVM-HELP,r=4.1.032 replaces
VRTSvxvm.VXVM-HELP,r=3.5~IA.014
- VRTSvxvm.VXVM-KRN,r=4.1.032 replaces
VRTSvxvm.VXVM-KRN,r=3.5~IA.014
- VRTSvxvm.VXVM-RUN,r=4.1.032 replaces
VRTSvxvm.VXVM-RUN,r=3.5~IA.014
- VRTSvxvm,r=4.1.032 replaces VRTSvxvm,r=3.5~IA.014
You can ignore this message if it refers only to one or more VRTS products. To ignore this message,
press Enter when prompted, and continue with the update.
For more information on updating your system to HP-UX 11i v3 using the update-ux command,
see the HP-UX 11i v3 Installation and Update Guide. To locate this document, go to the HP-UX
Core docs page at: www.hp.com/go/hpux-core-docs On this page, select HP-UX 11i v3.
34 Installing the Veritas 5.1 SP1 Products