User's Manual
Table Of Contents
- HP ProLiant ML100 Series Server User Guide
- Abstract
- Notice
- Contents
- Server operations
- Server setup
- Hardware options installation
- Introduction
- Access panel
- Processor option
- Installing a processor in HP ProLiant ML150 Generation 3 and Generation 5 Servers
- Installing a processor in HP ProLiant ML110 (G2, G3, and G4) and ProLiant ML150 Generation 2 Servers
- Installing a processor in HP ProLiant ML110 Generation 5 Servers
- Installing a processor in HP ProLiant ML115 and ML115 Generation 5 Servers
- SAS or SATA hard drive options
- Hard drive LED cable option
- Removable media device options
- Memory options
- Expansion board options
- Server software and configuration utilities
- Troubleshooting
- Pre-diagnostic steps
- Troubleshooting flowcharts
- Hardware problems
- Power problems
- General hardware problems
- Internal system problems
- System open circuits and short circuits
- External device problems
- Audio problems
- Printer problems
- Mouse and keyboard problems
- Modem problems
- No dial tone exists
- No response occurs when you type AT commands
- AT commands are not visible
- Data is displayed as garbled characters after the connection is established
- Modem does not answer an incoming call
- Modem does not connect to another modem
- Modem disconnects while online
- AT command initialization string is not working
- Connection errors are occurring
- You are unable to connect to an online subscription service
- You are unable to connect at 56 Kbps
- Network controller problems
- Software problems
- Firmware maintenance
- Battery replacement
- Regulatory compliance notices
- Regulatory compliance identification numbers
- Federal Communications Commission notice
- Declaration of conformity for products marked with the FCC logo, United States only
- Modifications
- Cables
- Canadian notice (Avis Canadien)
- European Union regulatory notice
- Disposal of waste equipment by users in private households in the European Union
- Japanese notice
- BSMI notice
- Korean notice
- Laser compliance
- Battery replacement notice
- Taiwan battery recycling notice
- Power cord statement for Japan
- Acoustics statement for Germany (Geräuschemission)
- Electrostatic discharge
- Support and other resources
- Acronyms and abbreviations
- Documentation feedback
- Index
Server setup 10
WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that:
• The leveling jacks are extended to the floor.
• The full weight of the rack rests on the leveling jacks.
• The stabilizing feet are attached to the rack if it is a single-rack installation.
• The racks are coupled together in multiple-rack installations.
• Only one component is extended at a time. A rack may become unstable if more than one
component is extended for any reason.
WARNING: To reduce the risk of personal injury or equipment damage when unloading a rack:
• At least two people are needed to safely unload the rack from the pallet. An empty 42U rack
can weigh as much as 115 kg (253 lb), can stand more than 2.1 m (7 ft) tall, and might
become unstable when being moved on its casters.
• Never stand in front of the rack when it is rolling down the ramp from the pallet. Always handle
the rack from both sides.
Installing hardware options
Install any hardware options before initializing the server. For options installation information, refer to the
option documentation. For server-specific information, refer to "Hardware options installation (on page 11)."
Powering up and configuring the server
To power up the server, press the Power On/Standby button.
For detailed information on configuring the server, see the server installation sheet.
Installing the operating system
To operate properly, the server must have a supported operating system. For the latest information on
supported operating systems, refer to the HP website (http://www.hp.com/go/supportos).
To install an operating system on the server, insert the operating system CD into the CD-ROM drive and
reboot the server. This process may require you to obtain additional drivers from the Easy Set-up CD or the
support CD shipped with the server, or the CD that shipped with the option. The drivers may have updates
that are available on the HP website (http://www.hp.com/support).
Follow the on-screen instructions to begin the installation process.
Registering the server
To register the server, refer to the HP Registration website (http://register.hp.com).