HP ProLiant SL390s G7 1U Half-width Server User Guide Abstract This document identifies the components and details the usage of the HP ProLiant SL390s G7 1U Half-width Server. This document is intended for the person who installs, administers, and troubleshoots servers and storage systems. This person should be qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels.
© Copyright 2010, 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft® and Windows® are U.S.
Contents Component identification ............................................................................................................... 6 Front panel components ................................................................................................................................ 6 Front panel LEDs and buttons ......................................................................................................................... 7 Rear panel components ...................................
Battery cabling for BBWC ........................................................................................................................... 34 Configuration and utilities ............................................................................................................ 35 Configuration tools ..................................................................................................................................... 35 SmartStart software ..........................................
Warranty information ................................................................................................................................. 64 Electrostatic discharge ................................................................................................................. 65 Preventing electrostatic discharge ................................................................................................................ 65 Grounding methods to prevent electrostatic discharge ............
Component identification Front panel components NOTE: This figure illustrates the left and right system trays.
Item Description 22 Power LED/SW 23 Serial port (RJ45 style) VGA port 24 *By default, the HP NC543i 2-port 4x QDR IB/10Gb Adapter is configured as a dual-port 10 GigE device. If the InfiniBand Enablement kit is installed, then the onboard QSFP port functions as InfiniBand, and the device operates as a 1-port 10 GigE (SFP+) and 1-port QDR InfiniBand (QSFP).
Item Description Status 10 QSFP/InfiniBand activity LED Amber—Logical link established. Flashing amber—Activity exists. Off—No activity exists, or no connection exists.* 11 SFP+/10 GigE link LED Green—Linking Off—No connection exists. 12 SFP+/10 GigE activity LED Flashing green—Activity exists. Off—No activity exists, or no connection exists. 13 Power On/Standby button and system power LED Green—System on Amber—System shut down, but power still applied.
Rear panel LEDs and buttons Item Description Status 1 Fan 8 power LED Off—Normal Amber—Fan has failed. 2 Fan 7 power LED Off—Normal Amber—Fan has failed. 3 UID LED button Blue—Activated Flashing blue—System is being remotely managed. Off—Deactivated 4 Fan 4 power LED Off—Normal Amber—Fan has failed. 5 Fan 3 power LED Off—Normal Amber—Fan has failed. 6 Fan 1 power LED Off—Normal Amber—Fan has failed. 7 Fan 2 power LED Off—Normal Amber—Fan has failed.
System board components Item Designator Description 1 J1 CPU 1 DIMM slot 6A 2 J2 CPU 1 DIMM slot 5D 3 J4 CPU 1 DIMM slot 4B 4 J5 CPU 1 DIMM slot 3E 5 J7 CPU 1 DIMM slot 2C 6 J8 CPU 1 DIMM slot 1F 7 XU2 CPU 2 socket 8 CPU2 VRD and CPU1 DIMM VRD 9 U10 U22 U41 U51 U12 U10 U14 U11 J25 10 J22 SATA 5 Connector 11 J32 SATA 1 Connector 12 J9 SATA 2 Connector 13 J18 SATA 3 Connector 14 J19 SATA 4 Connector 15 J56 QPI connector 16 J24 Riser connector SATA 6 Connector
Item Designator Description 22 J17 CPU2 DIMM slot 1F 23 XU1 CPU 1 socket 24 CPU1 VRD 25 U24 U5 U4 U30 U27 J36 26 J42 RPS connector Power connector DIMM slots DIMM slots are identified by the numbers 1 through 6. DIMM population order is specified by the letters A through F. System board switches System maintenance switch Position Default Function S1 Off Off—iLO 3 security is enabled. On—iLO 3 security is disabled. S2 Off Off—System configuration can be changed.
When the system maintenance switch position 6 is set to the On position, the system is prepared to erase all system configuration settings from both CMOS and NVRAM. CAUTION: Clearing CMOS and/or NVRAM deletes configuration information. There is an RBSU setting that erases default settings and fixed disk partitions, which causes a loss of data.
NOTE: LFF hard drives are illustrated in the figures in this guide. SFF hard drives are also supported. Battery pack LEDs Item Color Description 1 Green System Power LED. This LED is on when the system is powered up and 12 V system power is available. This power supply is used to maintain the battery charge and provide supplementary power to the cache microcontroller. 2 Green Auxiliary Power LED. This LED is on when 3.3V auxiliary voltage is detected.
LED3 pattern LED4 pattern Interpretation Off Flashing (1 Hz) The battery pack is below the minimum charge level and is being charged. Features that require a battery (such as write cache, capacity expansion, stripe size migration, and RAID migration) are unavailable temporarily until charging is complete. The recharge process takes between 15 minutes and 2 hours, depending on the initial capacity of the battery. Off On The battery pack is fully charged, and posted write data is stored in the cache.
Operations Power down the server WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment, remove the power cord to remove power from the server. The front panel Power On/Standby button does not completely shut off system power. Portions of the power supply and some internal circuitry remain active until AC power is removed. IMPORTANT: If installing a hot-plug device, it is not necessary to power down the server. 1. Back up the server data. 2.
4. Remove the left server from the chassis. 5. Repeat the previous steps to remove the right server from the chassis.
Setup Optional installation services Delivered by experienced, certified engineers, HP Care Pack services help you keep your servers up and running with support packages tailored specifically for HP ProLiant systems. HP Care Packs let you integrate both hardware and software support into a single package. A number of service level options are available to meet your needs.
Space and airflow requirements To allow for servicing and adequate airflow, observe the following space and airflow requirements when deciding where to install a rack: • Leave a minimum clearance of 63.5 cm (25 in) in front of the rack. • Leave a minimum clearance of 76.2 cm (30 in) behind the rack. • Leave a minimum clearance of 121.9 cm (48 in) from the back of the rack to the back of another rack or row of racks.
CAUTION: To reduce the risk of damage to the equipment when installing third-party options: • Do not permit optional equipment to impede airflow around the server or to increase the internal rack temperature beyond the maximum allowable limits. • Do not exceed the manufacturer’s TMRA. Power requirements Installation of this equipment must comply with local and regional electrical regulations governing the installation of information technology equipment by licensed electricians.
WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: • • • • • The leveling jacks are extended to the floor. The full weight of the rack rests on the leveling jacks. The stabilizing feet are attached to the rack if it is a single-rack installation. The racks are coupled together in multiple-rack installations. Only one component is extended at a time. A rack may become unstable if more than one component is extended for any reason.
Installing the server into the chassis 1. Insert the system tray into the chassis. 2. Connect peripheral devices to the server. NOTE: This figure illustrates the left and right system trays.
Item Description 10 UID LED/SW 11 USB connectors 12 NIC 2 network port 13 QSFP/InfiniBand port* 14 SFP+/10 GigE port* 15 Power LED/SW 16 Serial port (RJ45 style) 17 VGA port 18 USB connectors 19 NIC 2 network port 20 QSFP/InfiniBand port* 21 SFP+/10 GigE port* 22 Power LED/SW 23 Serial port (RJ45 style) VGA port 24 *By default, the HP NC543i 2-port 4x QDR IB/10Gb Adapter is configured as a dual-port 10 GigE device.
For information on using these installation paths, refer to the SmartStart installation poster in the HP ProLiant Essentials Foundation Pack, included with the server. Powering up and configuring the server To power up the server, press the Power On/Standby button. While the server boots, RBSU and the ORCA utility are automatically configured to prepare the server for operating system installation.
Hardware options installation Introduction If more than one option is being installed, read the installation instructions for all the hardware options and identify similar steps to streamline the installation process. WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: To prevent damage to electrical components, properly ground the server before beginning any installation procedure.
7. Rotate the drive carrier handle down. 8. Lock the drive carrier latches. 9. Install the server into the chassis ("Installing the server into the chassis" on page 21). 10. Connect the peripheral devices to the server. 11. Power up the server ("Powering up and configuring the server" on page 23). NOTE: LFF hard drives are illustrated in the figures in this guide. SFF hard drives are also supported.
7. Lift the drive assembly out of the tray. 8. Rotate the drive carrier handle down. 9. Lock the drive carrier latches. 10. Install the server into the chassis ("Installing the server into the chassis" on page 21). 11. Connect the peripheral devices to the server. 12. Power up the server ("Powering up and configuring the server" on page 23).
4. Open the processor locking lever and the processor socket retaining bracket. Do not remove the processor socket cover. IMPORTANT: Be sure the processor remains inside the processor installation tool. 5. If the processor has separated from the installation tool, carefully re-insert the processor in the tool. Handle the processor by the edges only, and do not touch the bottom of the processor, especially the contact area.
6. Align the processor installation tool with the socket, and then install the processor. THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. CAUTION: THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. To avoid damage to the system board: • Never install or remove a processor without using the processor installation tool. • Do not touch the processor socket contacts. • Do not tilt or slide the processor when lowering the processor into the socket.
7. Press the tabs on the processor installation tool to separate it from the processor, and then remove the tool. 8. Close the processor socket retaining bracket and the processor locking lever. The processor socket cover is automatically ejected. Remove the cover. CAUTION: Be sure to close the processor socket retaining bracket before closing the processor locking lever. The lever should close without resistance.
9. Remove the heatsink protective cover. CAUTION: Heatsink screws should be tightened and loosened in alternating sequence. Do not overtighten the screws as this can damage the system board, connectors, or screws. When using a torque wrench, tighten the screws to 0.68 to 0.90 Nm (6 to 8 in-lb.) of torque. 10. Install the heatsink: a. Position the heatsink on the processor backplate. b. Tighten the first screw about three quarters in, and then tighten the second screw completely. c.
DIMMs Memory configurations The server has 12 DIMM slots that support up to 96 GB maximum system memory. If you add or replace memory modules, follow these guidelines: • You can install a maximum of 12 DDR3 240-pin RDIMMs (SR, DR, QR) or UDIMMs (SR, DR) slots (6 DIMMs per CPU). • Channel 0 is located farthest from the processor, followed by channel 1, and then channel 2. • Of the two DIMMs in a given channel, DIMM 0 is the farthest from the processor.
3. Remove the server from the chassis (on page 15). 4. Open the DIMM slot latches. 5. Install the DIMM. 6. Install the server into the chassis ("Installing the server into the chassis" on page 21). 7. Connect the peripheral devices to the server. 8. Power up the server ("Powering up and configuring the server" on page 23). Expansion board options The server supports PCI, PCI-X, and PCI Express expansion boards. Installing a low-profile expansion board 1. Power down the server (on page 15). 2.
4. Remove the PCI riser cage. 5. Remove the expansion slot cover. 6. Install a low-profile expansion board. 7. Install the PCI riser cage. 8. Connect all necessary internal cabling to the expansion board. For more information on these cabling requirements, see the documentation that ships with the option. 9. Install the server into the chassis ("Installing the server into the chassis" on page 21). 10. Connect the peripheral devices to the server. 11.
Cabling SAS or SATA power cabling options For server-specific SAS or SATA power cabling installation instructions, see the installation sheet included with the option kit.
Configuration and utilities Configuration tools SmartStart software SmartStart is a collection of software that optimizes single-server setup, providing a simple and consistent way to deploy server configuration. SmartStart has been tested on many ProLiant server products, resulting in proven, reliable configurations.
refer to the SmartStart Scripting Toolkit User Guide on the HP website (http://h18004.www1.hp.com/products/servers/management/toolkit/documentation.html).
NOTE: If the boot drive is not empty or has been written to in the past, ORCA does not automatically configure the array. You must run ORCA to configure the array settings. Drives installed Drives used RAID level 1 1 RAID 0 2 2 RAID 1 3, 4, 5, or 6 3, 4, 5, or 6 RAID 5 More than 6 0 None To change any ORCA default settings and override the auto-configuration process, press the F8 key when prompted. By default, the auto-configuration process configures the system for the English language.
• Remains available any time that the server is on • Displays on-screen tips for individual steps of a configuration procedure • Beginning with ACU version 8.28.13.0, provides diagnostic functionality on the Diagnostics tab (formerly known as Array Diagnostics Utility). For optimum performance, the minimum display settings are 1024 × 768 resolution and 16-bit color. Servers running Microsoft® operating systems require one of the following supported browsers: • Internet Explorer 6.
Solution while providing optimization for deployment of HP ProLiant servers using HP ProLiant Integration Module. HP Insight Control facilitates the installation, configuration, and deployment of high-volumes of servers through an intuitive, comprehensive console, using either scripting or imaging technology. It makes deploying a server as easy as selecting one, a few, or hundreds of target servers, selecting predefined images or scripts, and clicking Run.
The ROMPaq utility checks the system and provides a choice (if more than one exists) of available firmware revisions. For more information, go to the HP website (http://www.hp.com/go/hpsc) and click on Drivers, Software & Firmware. Then, enter your product name in the Find an HP product field and click Go. To access the server-specific page for this server, enter the following web address into the browser: http://www.hp.com/support/sl390sg7 (http://www.hp.
• Easy node and identification through UID indicators • Support of logging through standard syslog servers For additional information about setting up and using SLAPM, see the HP ProLiant SL Advanced Power Manager User Guide (http://h20000.www2.hp.com/bc/docs/support/SupportManual/c02018322/c02018322.pdf?jumpi d=reg_R1002_USEN). Redundant ROM support The server enables you to upgrade or configure the ROM safely with redundant ROM support. The server has an 8-MB ROM that acts as two, separate 4-MB ROMs.
External USB functionality HP provides external USB support to enable local connection of USB devices for server administration, configuration, and diagnostic procedures. For additional security, external USB functionality can be disabled through RBSU.
o For Windows®: IML Viewer o For Linux: IML Viewer Application • From within the iLO 3 user interface • From within HP Insight Diagnostics (on page 42) For more information, see the Management CD or DVD in the HP Insight Foundation suite for ProLiant.
If you do not use the SmartStart CD to install an operating system, drivers for some of the new hardware are required. These drivers, as well as other option drivers, ROM images, and value-add software can be downloaded from the HP website (http://www.hp.com/support). IMPORTANT: Always perform a backup before installing or updating device drivers. ProLiant Support Packs PSPs represent operating system-specific bundles of ProLiant optimized drivers, utilities, and management agents.
Troubleshooting Troubleshooting resources The HP ProLiant Servers Troubleshooting Guide provides procedures for resolving common problems and comprehensive courses of action for fault isolation and identification, error message interpretation, issue resolution, and software maintenance on ProLiant servers and server blades. This guide includes problem-specific flowcharts to help you navigate complex troubleshooting processes. To view the guide, select a language: • English (http://www.hp.
Important safety information Before servicing this product, read the Important Safety Information document provided with the server. Symbols on equipment The following symbols may be placed on equipment to indicate the presence of potentially hazardous conditions. This symbol indicates the presence of hazardous energy circuits or electric shock hazards. Refer all servicing to qualified personnel. WARNING: To reduce the risk of injury from electric shock hazards, do not open this enclosure.
WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: • • • • • The leveling feet are extended to the floor. The full weight of the rack rests on the leveling feet. The stabilizing feet are attached to the rack if it is a single-rack installation. The racks are coupled together in multiple-rack installations. Only one component is extended at a time. A rack may become unstable if more than one component is extended for any reason.
Version Control Agent. The VCA gives you a list of names and versions of all installed HP drivers, Management Agents, and utilities, and whether they are up-to-date. o HP recommends you have access to the server documentation for server-specific information. o HP recommends you have access to the SmartStart CD for value-added software and drivers required during the troubleshooting process. Download the current version of SmartStart from the HP website (http://www.hp.com/servers/smartstart).
Before removing the components, be sure to determine the minimum configuration for each component and follow all guidelines in the server user guide. Always use the recommended minimum configuration above before removing any processors. If you are unable to isolate the issue with the configuration above, you will then remove all but one of the processors.
Troubleshooting flowcharts To effectively troubleshoot a problem, HP recommends that you start with the first flowchart in this section, "Start diagnosis flowchart (on page 50)," and follow the appropriate diagnostic path. If the other flowcharts do not provide a troubleshooting solution, follow the diagnostic steps in "General diagnosis flowchart (on page 51).
General diagnosis flowchart The General diagnosis flowchart provides a generic approach to troubleshooting. If you are unsure of the problem, or if the other flowcharts do not fix the problem, use the following flowchart.
Item See 4 The most recent version of a particular server blade or option firmware is available on the HP Support website (http://www.hp.com/support). 5 "General memory problems are occurring" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or see "Troubleshooting resources (on page 45)" 6 • • 7 • • • Maintenance and service guides for p-Class server blades, located on the Documentation CD or the HP website (http://www.hp.
Server blade power-on problems flowchart Symptoms: • The server does not power on. • The system power LED is off or amber.
• The health LED is red or amber. NOTE: For the location of server LEDs and information on their statuses, refer to the server documentation.
POST problems flowchart Symptoms: • Server does not complete POST NOTE: The server has completed POST when the system attempts to access the boot device.
Item See 1 Server blade power-on problems flowchart (on page 53) 2 "POST error messages and beep codes (on page 61)" 3 "Video problems" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or see "Troubleshooting resources (on page 45)" 4 "General memory problems are occurring" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or see "Troubleshooting resources (on page 45)" 5 "Breaking the server down to the minimum hardware configuration
OS boot problems flowchart There are two ways to use SmartStart when diagnosing OS boot problems on a server blade: • Use iLO to remotely attach virtual devices to mount the SmartStart CD onto the server blade. • Use a local I/O cable and drive to connect to the server blade, and then restart the server blade.
Possible causes: • Corrupted OS • Hard drive subsystem problem • Incorrect boot order setting in RBSU Item See 1 HP ROM-Based Setup Utility User Guide (http://www.hp.
* See the server blade OS boot problems flowchart (on page 57) Server fault indications flowchart Symptoms: • Server boots, but a fault event is reported by Insight Management Agents • Server boots, but the internal health LED, external health LED, or component health LED is red or amber Troubleshooting 59
NOTE: For the location of server LEDs and information on their statuses, refer to the server documentation.
POST error messages and beep codes For a complete listing of error messages, refer to the "POST error messages" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.com/support).
WARNING: To avoid potential problems, ALWAYS read the warnings and cautionary information in the server documentation before removing, replacing, reseating, or modifying system components.
System battery If the server no longer automatically displays the correct date and time, you might have to replace the battery that provides power to the real-time clock. Under normal use, battery life is 5 to 10 years. WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled. To reduce the risk of personal injury: • • • • Do not attempt to recharge the battery.
Regulatory information Safety and regulatory compliance For safety, environmental, and regulatory information, see Safety and Compliance Information for Server, Storage, Power, Networking, and Rack Products, available at the HP website (http://www.hp.com/support/Safety-Compliance-EnterpriseProducts). Turkey RoHS material content declaration Ukraine RoHS material content declaration Warranty information HP ProLiant and X86 Servers and Options (http://www.hp.
Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent electrostatic damage: • Avoid hand contact by transporting and storing products in static-safe containers.
Specifications Environmental specifications Specification Value Temperature range* Operating 10°C to 35°C (50°F to 95°F) Shipping -30°C to 50°C (-22°F to 122°F) Storage -30°C to 60°C (-22°F to 140°F) Maximum wet bulb temperature 28°C (82.4°F) Relative humidity (noncondensing)** Operating 10% to 90% Non-operating 5% to 95% * All temperature ratings shown are for sea level. An altitude derating of 1°C per 300 m (1.8°F per 1,000 ft) to 3048 m (10,000 ft) is applicable. No direct sunlight allowed.
Support and other resources Before you contact HP Be sure to have the following information available before you call HP: • Active Health System log (HP ProLiant Gen8 or later products) Download and have available an Active Health System log for 3 days before the failure was detected. For more information, see the HP iLO 4 User Guide or HP Intelligent Provisioning User Guide on the HP website (http://www.hp.com/go/ilo/docs).
providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship that part directly to you for replacement. There are two categories of CSR parts: • Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be charged for the travel and labor costs of this service. • Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair.
Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus d'informations sur ce programme en Amérique du Nord, consultez le site Web HP (http://www.hp.com/go/selfrepair). Riparazione da parte del cliente Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente dal cliente (CSR, Customer Self Repair).
HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet. CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag geliefert. Für bestimmte Standorte ist eine Lieferung am selben Tag oder innerhalb von vier Stunden gegen einen Aufpreis verfügbar.
sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes y escogerá la empresa de transporte que se utilice para dicho servicio. Para obtener más información acerca del programa de Reparaciones del propio cliente de HP, póngase en contacto con su proveedor de servicios local. Si está interesado en el programa para Norteamérica, visite la página web de HP siguiente (http://www.hp.com/go/selfrepair).
Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto. OBSERVAÇÃO: Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça.
Support and other resources 73
Support and other resources 74
Acronyms and abbreviations ABEND abnormal end ACU Array Configuration Utility ASR Automatic Server Recovery BBWC battery-backed write cache CONREP Configuration Replication utility CSA Canadian Standards Association CSR Customer Self Repair DDR3 double data rate-3 HP SIM HP Systems Insight Manager IEC International Electrotechnical Commission iLO Integrated Lights-Out IML Integrated Management Log Acronyms and abbreviations 75
KVM keyboard, video, and mouse LFF large form factor NMI nonmaskable interrupt NVRAM nonvolatile memory ORCA Option ROM Configuration for Arrays PCIe peripheral component interconnect express PCI-X peripheral component interconnect extended PDU power distribution unit POST Power-On Self Test PSP HP ProLiant Support Pack PXE preboot execution environment QPI QuickPath Interconnect QSFP quad small form-factor pluggable RBSU ROM-Based Setup Utility Acronyms and abbreviations 76
RDIMM registered dual in-line memory module RDP Rapid Deployment Pack RoHS Restriction of Hazardous Substances RPS redundant power supply SAS serial attached SCSI SATA serial ATA SFF small form factor SFP small form-factor pluggable SFP+ enhanced small form-factor pluggable SLAPM SL Advanced Power Manager SSD solid-state drive TMRA recommended ambient operating temperature UDIMM unregistered dual in-line memory module UID unit identification Acronyms and abbreviations 77
USB universal serial bus VCA Version Control Agent VRD Voltage Regulator Down Acronyms and abbreviations 78
Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (mailto:docsfeedback@hp.com). Include the document title and part number, version number, or the URL when submitting your feedback.
Index A ACU (Array Configuration Utility) additional information 45 airflow requirements 17, 18 Altiris Deployment Solution 38 Array Configuration Utility (ACU) ASR (Automatic Server Recovery) authorized reseller 67 auto-configuration process 36 Automatic Server Recovery (ASR) 37 37 39 39 B battery 34, 63 battery pack LEDs 13 battery-backed write cache battery pack 34 BIOS Serial Console 37 BIOS upgrade 39 boot options 37 buttons 6, 8, 9, 10 C cable management arm 20 cables 34, 49 cabling 34 Care Pack
IML (Integrated Management Log) 42 Important Safety Information document 45 Insight Diagnostics 42, 43 installation, server options 20, 24 installing hardware 21, 24 installing operating system 22 installing server into chassis 21 Integrated Lights-Out (iLO) 40 Integrated Management Log (IML) 42 ProLiant Support Pack (PSP) 44 PSPs, overview 44 R NMI functionality 12 rack installation 17, 19 rack mounting hardware 20 rack resources 17 rack warnings 19 RBSU (ROM-Based Setup Utility) 36 RBSU configuration
supported operating systems 44 switches 11 symbols on equipment 46 system battery 63 system board components 10, 11 System Erase Utility 40 system power LED 13 T technical support 67 telephone numbers 67 temperature requirements 18 troubleshooting 45, 48, 50 U UID LED 9 updating the system ROM 41 USB support 41 utilities 35 utilities, deployment 35, 36, 38 V ventilation 17 W warnings 19, 46 Index 82
