Manual
Table Of Contents
- HP ProLiant ML100 Series Server User Guide
- Abstract
- Notice
- Contents
- Server operations
- Server setup
- Hardware options installation
- Introduction
- Access panel
- Processor option
- Installing a processor in HP ProLiant ML150 Generation 3 and Generation 5 Servers
- Installing a processor in HP ProLiant ML110 (G2, G3, and G4) and ProLiant ML150 Generation 2 Servers
- Installing a processor in HP ProLiant ML110 Generation 5 Servers
- Installing a processor in HP ProLiant ML115 and ML115 Generation 5 Servers
- SAS or SATA hard drive options
- Hard drive LED cable option
- Removable media device options
- Memory options
- Expansion board options
- Server software and configuration utilities
- Troubleshooting
- Pre-diagnostic steps
- Troubleshooting flowcharts
- Hardware problems
- Power problems
- General hardware problems
- Internal system problems
- System open circuits and short circuits
- External device problems
- Audio problems
- Printer problems
- Mouse and keyboard problems
- Modem problems
- No dial tone exists
- No response occurs when you type AT commands
- AT commands are not visible
- Data is displayed as garbled characters after the connection is established
- Modem does not answer an incoming call
- Modem does not connect to another modem
- Modem disconnects while online
- AT command initialization string is not working
- Connection errors are occurring
- You are unable to connect to an online subscription service
- You are unable to connect at 56 Kbps
- Network controller problems
- Software problems
- Firmware maintenance
- Battery replacement
- Regulatory compliance notices
- Regulatory compliance identification numbers
- Federal Communications Commission notice
- Declaration of conformity for products marked with the FCC logo, United States only
- Modifications
- Cables
- Canadian notice (Avis Canadien)
- European Union regulatory notice
- Disposal of waste equipment by users in private households in the European Union
- Japanese notice
- BSMI notice
- Korean notice
- Laser compliance
- Battery replacement notice
- Taiwan battery recycling notice
- Power cord statement for Japan
- Acoustics statement for Germany (Geräuschemission)
- Electrostatic discharge
- Support and other resources
- Acronyms and abbreviations
- Documentation feedback
- Index
Hardware options installation 34
Removable media device options
Depending on the model, ProLiant 100 Series servers require different installation procedures for media
devices.
Server Device support Procedure
ProLiant ML110 G2 Server
Half-height and full-height Installing media devices with a media latch (on
page 37)
ProLiant ML110 G3 Server
Half-height Installing media devices with screws (on page
35)
ProLiant ML110 G4 Server
Half-height Installing media devices with screws (on page
35)
ProLiant ML110 G5 Server
Half-height Installing media devices with screws (on page
35)
ProLiant ML115 Server
Half-height Installing media devices with screws (on page
35)
ProLiant ML115 G5 Server
Half-height Installing media devices with screws (on page
35)
ProLiant ML150 G2 Server
Half-height Installing media devices with rails (on page 34)
ProLiant ML150 G3 Server
Half-height and full-height Installing media devices with screws (on page
35)
ProLiant ML150 G5 Server
Half-height and full-height Installing media devices with wire retainers (on
page 38)
Installing media devices with rails
NOTE: This process only represents one installation method. For specific instructions for
installing the media device into the server, refer to the installation sheet for your specific server.
1. Power down the server (on page 6).
2. Extend the server from the rack, if applicable.
3. Remove the access panel ("Access panel" on page 11).
4. Access the removable media cage.
5. Remove the bezel blank.
NOTE: HP recommends that you remove all bezel blanks to facilitate drive installation.
6. Depending on the server, obtain the screws from one of the following locations:
o Bezel blank
o Chassis
o Accessory kit