Manual
Table Of Contents
- HP ProLiant ML100 Series Server User Guide
- Abstract
- Notice
- Contents
- Server operations
- Server setup
- Hardware options installation
- Introduction
- Access panel
- Processor option
- Installing a processor in HP ProLiant ML150 Generation 3 and Generation 5 Servers
- Installing a processor in HP ProLiant ML110 (G2, G3, and G4) and ProLiant ML150 Generation 2 Servers
- Installing a processor in HP ProLiant ML110 Generation 5 Servers
- Installing a processor in HP ProLiant ML115 and ML115 Generation 5 Servers
- SAS or SATA hard drive options
- Hard drive LED cable option
- Removable media device options
- Memory options
- Expansion board options
- Server software and configuration utilities
- Troubleshooting
- Pre-diagnostic steps
- Troubleshooting flowcharts
- Hardware problems
- Power problems
- General hardware problems
- Internal system problems
- System open circuits and short circuits
- External device problems
- Audio problems
- Printer problems
- Mouse and keyboard problems
- Modem problems
- No dial tone exists
- No response occurs when you type AT commands
- AT commands are not visible
- Data is displayed as garbled characters after the connection is established
- Modem does not answer an incoming call
- Modem does not connect to another modem
- Modem disconnects while online
- AT command initialization string is not working
- Connection errors are occurring
- You are unable to connect to an online subscription service
- You are unable to connect at 56 Kbps
- Network controller problems
- Software problems
- Firmware maintenance
- Battery replacement
- Regulatory compliance notices
- Regulatory compliance identification numbers
- Federal Communications Commission notice
- Declaration of conformity for products marked with the FCC logo, United States only
- Modifications
- Cables
- Canadian notice (Avis Canadien)
- European Union regulatory notice
- Disposal of waste equipment by users in private households in the European Union
- Japanese notice
- BSMI notice
- Korean notice
- Laser compliance
- Battery replacement notice
- Taiwan battery recycling notice
- Power cord statement for Japan
- Acoustics statement for Germany (Geräuschemission)
- Electrostatic discharge
- Support and other resources
- Acronyms and abbreviations
- Documentation feedback
- Index
Hardware options installation 11
Hardware options installation
Introduction
If more than one option is being installed, read the installation instructions for all the hardware options and
identify similar steps to streamline the installation process.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
CAUTION: To prevent damage to electrical components, properly ground the server before
beginning any installation procedure. Improper grounding can cause electrostatic discharge.
Access panel
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
CAUTION: Do not operate the server for long periods with the access panel open or removed.
Operating the server in this manner results in improper airflow and improper cooling that can
lead to thermal damage.
1. Power down the server (on page 6).
2. Extend the server from the rack, if applicable.
3. Loosen the two thumbscrews located on the server rear panel, if applicable.
4. Slide the access panel back about 1.5 cm (0.5 in).
5. Lift and remove the access panel.
To install the component, reverse the removal procedure.
Processor option
This section provides the following procedures:
• Installing a processor in HP ProLiant ML150 Generation 3 and Generation 5 Servers (on page 12)
• Installing a processor in HP ProLiant ML110 (G2, G3, and G4) and ProLiant ML150 Generation 2
Servers (on page 15)
• Installing a processor in HP ProLiant ML110 Generation 5 Servers (on page 16)
• Installing a processor in HP ProLiant ML115 and ML115 Generation 5 Servers (on page 18)
For more information on installing a processor in a specific server, see the documentation that ships with the
processor option kit.