HP ProLiant ML310 Generation 5 Server Maintenance and Service Guide Part Number 450223-004 August 2008 (Fourth Edition)
© Copyright 2007, 2008 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft, Windows, and Windows Server are U.S.
Contents Customer self repair ...................................................................................................................... 5 Parts only warranty service ......................................................................................................................... 5 Illustrated parts catalog ............................................................................................................... 16 Mechanical components.............................................
Cabling ..................................................................................................................................... 59 Server cabling ........................................................................................................................................ 59 SATA hard drive cabling .......................................................................................................................... 60 SAS hard drive cabling .......................................
Customer self repair HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and allow for greater flexibility in performing defective parts replacement. If during the diagnosis period HP (or HP service providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship that part directly to you for replacement. There are two categories of CSR parts: • Mandatory—Parts for which customer self repair is mandatory.
• Obligatoire - Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés. • Facultatif - Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également conçues pour permettre au client d'effectuer lui-même la réparation.
NOTA: alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per rispettare la garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza autorizzato. Tali parti sono identificate da un "No" nel Catalogo illustrato dei componenti. In base alla disponibilità e alla località geografica, le parti CSR vengono spedite con consegna entro il giorno lavorativo seguente.
anrufen und sich von einem Mitarbeiter per Telefon helfen lassen. Den Materialien, die mit einem CSRErsatzteil geliefert werden, können Sie entnehmen, ob das defekte Teil an HP zurückgeschickt werden muss. Wenn es erforderlich ist, das defekte Teil an HP zurückzuschicken, müssen Sie dies innerhalb eines vorgegebenen Zeitraums tun, in der Regel innerhalb von fünf (5) Geschäftstagen.
Centro de asistencia técnica de HP y recibirá ayuda telefónica por parte de un técnico. Con el envío de materiales para la sustitución de componentes CSR, HP especificará si los componentes defectuosos deberán devolverse a HP. En aquellos casos en los que sea necesario devolver algún componente a HP, deberá hacerlo en el periodo de tiempo especificado, normalmente cinco días laborables. Los componentes defectuosos deberán devolverse con toda la documentación relacionada y con el embalaje de envío.
periode, gewoonlijk vijf (5) werkdagen, retourneren aan HP. Het defecte onderdeel moet met de bijbehorende documentatie worden geretourneerd in het meegeleverde verpakkingsmateriaal. Als u het defecte onderdeel niet terugzendt, kan HP u voor het vervangende onderdeel kosten in rekening brengen. Bij reparatie door de klant betaalt HP alle verzendkosten voor het vervangende en geretourneerde onderdeel en kiest HP zelf welke koerier/transportonderneming hiervoor wordt gebruikt.
Serviço de garantia apenas para peças A garantia limitada da HP pode incluir um serviço de garantia apenas para peças. Segundo os termos do serviço de garantia apenas para peças, a HP fornece as peças de reposição sem cobrar nenhuma taxa. No caso desse serviço, a substituição de peças CSR é obrigatória. Se desejar que a HP substitua essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
Customer self repair 12
Customer self repair 13
Customer self repair 14
Customer self repair 15
Illustrated parts catalog Mechanical components Item 1 Front 2 Access 3 Pla 4 Description bezel panel Spare part number Customer self repair (on page 5) 459183-001 Mandatory 1 460024-001 Mandatory1 460421-001 Mandatory1 a) Fan holder — — b) System air baffle and PCI card guide — — c) Server feet — — Hard drive blank 459187-001 Mandatory1 stics kit Mandatory—Parts for which customer self repair is mandatory.
No—Some HP parts are not designed for customer self repair. In order to satisfy the customer warranty, HP requires that an authorized service provider replace the part. These parts are identified as "No" in the Illustrated Parts Catalog. 3 Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés.
Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto. 3 No: Nenhuma—Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça.
System components Item Description Spare part number Customer self repair (on page 5) 459188-001 Mandatory1 457021-001 Mandatory1 — — System components 5 Fa n 6 Processor heatsink 7 Processor a) 1.6-GHz Intel® Celeron® 420, single-core, 512-KB L2 cache, 800-MHz FSB 454523-001 Op tional2 b) 1.8-GHz Intel® Pentium® 2160, dual-core, 1MB L2 cache, 800-MHz FSB* 455623-001 Op tional2 c) 2.33-GHz Intel® Xeon® 3065, dual-core, 4MB L2 cache, 1333-MHz FSB* 454525-001 Op tional2 d) 2.
Item Description Spare part number Customer self repair (on page 5) h) 2.40-GHz Intel® Xeon® 3220, quad-core, 8MB L2 cache, 1066-MHz FSB* 454529-001 Op tional2 i) 2.00-GHz Intel® Core™2 E4400, dual-core, 2MB L2 cache, 800-MHz FSB* 454528-001 Op tional2 j) 2.40-GHz Intel® Core™2 E4600, dual-core, 2MB L2 cache, 800-MHz FSB* 462569-001 Op tional2 k) 2.66-GHz Intel® Xeon® X3350, quad-core, 12-MB L2 cache, 1333-MHz FSB* 463507-001 Op tional2 l) 2.
Item Description Spare part number Customer self repair (on page 5) 447464-001 Mandatory1 — — a) Hot-plug power supply, 430-W 432479-001 Mandatory1 b) Non-hot-plug power supply, 410-W* 460422-001 Mandatory1 Power supply cage with backplane 432478-001 Mandatory1 battery 234556-001 Mandatory1 16 Optical drive cable* 459189-001 Mandatory1 17 SAS/SATA hard drive cable* 459190-001 Mandatory1 18 SAS hard drive cable* 459934-001 Mandatory1 19 Power button/LED cable* 459186-001 Ma
No: Non—Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la réparation. Pour que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit effectué par un Mainteneur Agréé. Ces pièces sont identifiées par la mention “Non” dans le Catalogue illustré. 3 Mandatory: Obbligatorie—Parti che devono essere necessariamente riparate dal cliente.
Illustrated parts catalog 23
Removal and replacement procedures Required tools You need the following items for some procedures: • T-10/T-15 Torx screwdriver (included with the server) • HP Insight Diagnostics software ("HP Insight Diagnostics" on page 61) Safety considerations Before performing service procedures, review all the safety information. Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment, remove the power cord to remove power from the server. The front panel Power On/Standby button does not completely shut off system power. Portions of the power supply and some internal circuitry remain active until AC power is removed.
WARNING: This server is very heavy. To reduce the risk of personal injury or damage to the equipment: • Observe local occupational health and safety requirements and guidelines for manual material handling. • Get help to lift and stabilize the product during installation or removal, especially when the product is not fastened to the rails. When the server weighs more than 22.5 kg (50 lb), at least two people must lift the server into the rack together.
Unlock the bezel Unlock and remove the bezel before accessing the hard drive cage and media bays. Unlock the bezel before removing the access panel. Close and lock the bezel during normal server operations to ensure proper cooling airflow. Bezel Unlock and remove the bezel before accessing the hard drive cage and media bays. Unlock the bezel before removing the access panel. Close and lock the bezel during normal server operations to ensure proper cooling airflow. To remove the component: 1.
3. Remove the bezel. To replace the component, reverse the removal procedure. Access panel WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: Do not operate the server for long periods with the access panel open or removed. Operating the server in this manner results in improper airflow and improper cooling that can lead to thermal damage. To remove the component: 1.
3. Remove a bezel blank. To replace the component, reverse the removal procedure. Media bay blank To remove the component: 1. Power down the server (on page 26). 2. Remove the front bezel ("Bezel" on page 27). 3. Remove a media bay blank. To replace the component, reverse the removal procedure.
Hard drive blank Remove the component as indicated. To replace the component, slide the component into the bay until it clicks. Hard drives To remove the component: CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank. 1. Determine the status of the hard drive from the hot-plug hard drive LEDs ("Hot-plug SATA or SAS hard drive LEDs" on page 65).
3. Remove the hard drive. To replace the component: 1. Slide the drive into the cage until it clicks, locking the drive into place. 2. Close the lever. IMPORTANT: When the drive is inserted, the drive LEDs flash for 2 seconds to indicate that the drive is seated properly and receiving power. 3. As the drive begins to spin, be sure that the drive LEDs illuminate one at a time and then turn off together to indicate that the system has recognized the new drive. 4.
6. Remove the power button/LED cable. To replace the component, reverse the removal procedure. Temperature sensor To remove the component: 1. Power down the server (on page 26). 2. Remove the bezel ("Bezel" on page 27). 3. Remove the access panel ("Access panel" on page 28). 4. Disconnect the temperature sensor cable from the system board ("System board components" on page 68). 5. Remove the temperature sensor. To replace the component, reverse the removal procedure.
Front USB connectors To remove the component: 1. Power down the server (on page 26). 2. Remove the bezel ("Bezel" on page 27). 3. Remove the access panel ("Access panel" on page 28). 4. Disconnect the front USB cable from the system board ("System board components" on page 68). 5. Remove the front USB connectors. To replace the component, reverse the removal procedure. USB diskette drive Disconnect a USB diskette drive from the USB connector on the server front panel.
Diskette drive CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank. To remove the component: 1. Power down the server (on page 26). 2. Remove the bezel ("Bezel" on page 27). 3. Remove the access panel ("Access panel" on page 28). 4. Disconnect the power and data cables from the drive and the system board ("System board components" on page 68). 5. Remove the diskette drive.
5. Remove the SATA optical drive. To replace the component, reverse the removal procedure. Full-height tape drive CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank. To remove the component: 1. Power down the server (on page 26). 2. Remove the bezel ("Bezel" on page 27). 3. Remove the access panel ("Access panel" on page 28). 4.
5. Remove the full-height tape drive. To replace the component, reverse the removal procedure. USB tape drive CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank. To remove the component: 1. Power down the server (on page 26). 2. Remove the bezel ("Bezel" on page 27). 3. Remove the access panel ("Access panel" on page 28). 4.
5. Remove the USB tape drive. To replace the component, reverse the removal procedure. Hard drive cage and hard drive backplane To remove the component: 1. Power down the server (on page 26). 2. Remove the bezel ("Bezel" on page 27). 3. Remove the access panel ("Access panel" on page 28). 4. Remove all hot-plug hard drives ("Hard drives" on page 30). 5. Disconnect the power and data cables from the hard drive backplane and the system board ("System board components" on page 68). 6.
To replace the component, reverse the removal procedure. Rear fan and fan holder To remove the component: 1. Power down the server (on page 26). 2. Unlock the bezel (on page 27). 3. Remove the access panel ("Access panel" on page 28). 4. Remove the rear fan. 5. Remove the rear fan from the fan holder. To replace the component, reverse the removal procedure.
System air baffle and PCI card guide To remove the component: WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: Do not operate the server for long periods with the access panel open or removed. Operating the server in this manner results in improper airflow and improper cooling that can lead to thermal damage. 1. Power down the server (on page 26). 2. Unlock the bezel (on page 27). 3.
6. Remove the PCI fan. To replace the component, reverse the removal procedure. Non-redundant power supply To remove the component: 1. Power down the server (on page 26). 2. Unlock the bezel (on page 27). 3. Remove the access panel ("Access panel" on page 28). 4. Disconnect the power and signal cables from the system board ("System board components" on page 68). 5. Remove the power supply. To replace the component, reverse the removal procedure.
Hot-plug power supply CAUTION: Leave all failed power supplies installed until ready to replace with a working power supply. 1. Disconnect the power cord of the failed power supply from the AC power source. 2. Disconnect the power cord from the failed power supply. 3. Remove the power supply. To replace the component, reverse the removal procedure. Redundant power supply backplane assembly To remove the component: 1. Power down the server (on page 26). 2. Unlock the bezel (on page 27). 3.
6. Remove the redundant power supply backplane assembly. To replace the component, reverse the removal procedure. DIMM To remove the component: 1. Power down the server (on page 26). 2. Unlock the bezel (on page 27). 3. Remove the access panel ("Access panel" on page 28). 4. Remove the DIMM. To replace the component, reverse the removal procedure. IMPORTANT: DIMMs do not seat fully if turned the wrong way.
You can expand server memory by installing PC2-6400 DDR2 SDRAM DIMMs. The system supports up to four DIMMs for a maximum of 8 GB. For DIMM slot locations and bank assignments, see "System board components (on page 68)." Observe the following guidelines when installing additional memory: • DIMMs installed in the server must be unbuffered DDR2 SDRAM with ECC. • If only a single DIMM is installed, it must be installed in slot 1A. • All DIMMs installed must be the same speed.
To replace the heatsink: 1. Use the alcohol swab to remove all the existing thermal grease from the processor. Allow the alcohol to evaporate before continuing. 2. Apply new grease to the top of the processor in one of the following patterns to ensure even distribution. CAUTION: The heatsink thermal interface media is not reusable and must be replaced if the heatsink is removed from the processor after it has been installed. CAUTION: The heatsink is designed to fit one way in the server.
3. Align and install the heatsink with the arrow on the heatsink label pointing to the front of the server. 4. Connect the processor heatsink fan cable to the system board ("System board components" on page 68). When the heatsink is oriented properly, cable length is sufficient for the corresponding connector. 5. Install the access panel. 6. Lock the bezel. Processor CAUTION: Removal of the processor or heatsink renders the thermal layer between the processor and heatsink useless.
5. Open the processor retaining latch and the processor socket retaining bracket. 6. Using your fingers, remove the failed processor. To replace the component: IMPORTANT: Be sure the processor remains inside the processor installation tool.
1. If the processor has separated from the installation tool, carefully re-insert the processor in the tool. 2. Align the processor installation tool with the socket and install the spare processor. CAUTION: The processor is designed to fit one way into the socket. Use the alignment guides on the processor and socket to properly align the processor with the socket. Refer to the server hood label for specific instructions.
3. Press down firmly until the processor installation tool clicks and separates from the processor, and then remove the processor installation tool. 4. Close the processor retaining latch and the processor socket retaining bracket. 5. Clean the old thermal grease from the heatsink with the alcohol swab. Allow the alcohol to evaporate before continuing.
6. Apply all the grease to the top of the processor in one of the following patterns to ensure even distribution: CAUTION: The heatsink is designed to fit one way in the server. Failure to install the heatsink properly can result in thermal damage or equipment failure. CAUTION: Heatsink retaining screws should be tightened in diagonally opposite pairs (in an "X" pattern). 7. Align and install the heatsink with the arrow on the heatsink label pointing to the front of the server. 8.
Expansion boards To remove the component: 1. Power down the server (on page 26). 2. Unlock the bezel (on page 27). 3. Remove the bezel ("Bezel" on page 27). 4. Remove the access panel ("Access panel" on page 28). 5. Remove the expansion board. To replace the component, reverse the removal procedure. PCI-X extender board To remove the component: 1. Power down the server (on page 26). 2. Unlock the bezel (on page 27). 3. Remove the access panel ("Access panel" on page 28). 4.
6. Remove the PCI-X extender board. To replace the component, reverse the removal procedure. Battery If the server no longer automatically displays the correct date and time, you may need to replace the battery that provides power to the real-time clock. Under normal use, battery life is 5 to 10 years. WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled.
4. Remove the battery. To replace the component, reverse the removal procedure. IMPORTANT: After replacing the battery, the server is automatically configured with the default settings. The user can update these settings using RBSU. For more information about battery replacement or proper disposal, contact an authorized reseller or an authorized service provider. System board To remove the component: 1. Power down the server (on page 26). 2. Unlock the bezel (on page 27). 3.
10. Open the processor retaining latch and the processor socket retaining bracket. CAUTION: To avoid damage to the processor: • Handle the processor only by the edges. • Do not touch the bottom of the processor, especially the contact area.
11. Using your fingers, remove the processor from the failed system board. CAUTION: To avoid damage to the system board: • Do not touch the processor socket contacts. • Always install the processor socket cover after removing the processor from the socket. • Do not tilt or slide the processor when lowering the processor into the socket. 12. Remove the failed system board. To replace the system board: 1. Install the spare system board in the server before installing the processor. 2.
a. Open the processor retaining latch and the processor socket retaining bracket. b. Remove the processor socket protective cover. 3. Install the processor socket cover onto the processor socket of the failed system board. 4. Install the processor on the spare system board. CAUTION: The processor is designed to fit one way into the socket. Use the alignment guides on the processor and socket to properly align the processor with the socket. Refer to the server hood label for specific instructions.
5. Close the processor retaining latch and the processor socket retaining bracket. 6. Clean the old thermal grease from the heatsink and the top of the processor with the alcohol swab. Allow the alcohol to evaporate before continuing.
7. Apply all the grease to the top of the processor in one of the following patterns to ensure even distribution: CAUTION: The heatsink is designed to fit one way in the server. Failure to install the heatsink properly can result in thermal damage or equipment failure. CAUTION: Heatsink retaining screws should be tightened in diagonally opposite pairs (in an "X" pattern). 8. Align and install the heatsink with the arrow on the heatsink label pointing to the front of the server. 9.
10. Install all components removed from the failed system board. 11. Install the access panel. 12. Lock the bezel. 13. Power up the server. After you replace the system board, you must re-enter the server serial number and the product ID. 1. During the server startup sequence, press the F9 key to access RBSU. 2. Select the Advanced Options menu. 3. Select Serial Number. The following warning is displayed: Warning: The serial number should ONLY be modified by qualified service personnel.
Cabling Server cabling Item Description 1 SATA hard drive cable (hard drive) 2 Front USB cable 3 SATA optical drive cable 4 Front panel LED cable Cabling 59
SATA hard drive cabling Item Description 1 Power cable 2 SATA cable SAS hard drive cabling Item 1 Power 2 SAS Description cable cable Cabling 60
Diagnostic tools Troubleshooting resources The HP ProLiant Servers Troubleshooting Guide provides procedures for resolving common problems and comprehensive courses of action for fault isolation and identification, error message interpretation, issue resolution, and software maintenance on ProLiant servers and server blades. This guide includes problemspecific flowcharts to help you navigate complex troubleshooting processes. To view the guide, select a language: • English (http://www.hp.
Survey functionality is installed with every SmartStart-assisted HP Insight Diagnostics installation, or it can be installed through the HP PSP. NOTE: The current version of SmartStart provides the memory spare part numbers for the server. To download the latest version, see the HP website (http://www.hp.com/support). Integrated Management Log The IML records hundreds of events and stores them in an easy-to-view form. The IML timestamps each event with 1-minute granularity.
Component identification Front panel components Item Description 1 DVD-ROM drive 2 Media bays (bezel blanks) 3 USB connectors (2) 4 Bezel 5 lock Hard drive bays Component identification 63
Front panel LEDs and buttons Item Description Status 1 DVD-ROM drive ejector button — 2 DVD-ROM drive activity LED On = Activity Off = No activity 3 Power On/Standby button — 4 System power LED Green = AC power is functioning Amber = AC power is in standby mode Off = AC power is not available 5 Hard drive activity LED Green = Activity Off = No activity 6 NIC link/activity LED Green = Linked Flashing green = Linked with activity on the network Off = No network link 7 Internal health LE
SAS and SATA device numbers Hot-plug SATA or SAS hard drive LEDs Item LED description Status 1 Fault/UID status Amber = Drive failure Flashing amber = Fault-process activity Blue = Unit identification is active Off = No fault-process activity 2 Online/Activity status Green = Drive activity Flashing green = High activity on the drive or drive is being configured as part of an array Off = No drive activity Component identification 65
The online/activity status LED will not illuminate if using SATA drives connected to the embedded storage device. In this configuration, SATA hard drive activity can be identified using the hard drive activity LED on the system front panel. Rear panel components The server may look different from that shown.
Rear panel LEDs • Redundant hot-plug power supply model Item LED Status 1 NIC/iLO 2 link On = Link Off = No link 2 NIC/iLO 2 activity Flashing = Activity Off = No activity 3 Redundant power supply Green = Power supply is on and functioning Off = Power supply is not connected or power supply fault • Non-redundant non-hot-plug power supply model Component identification 67
Item LED Status 1 NIC/iLO 2 link On = Link Off = No link 2 NIC/iLO 2 activity Flashing = Activity Off = No activity System board components For this server, some system board slots and connectors are reserved.
Item Description 17 System maintenance switch 18 PCI fan connector 19 System battery 20 SATA connector 4 (hard drive) 21 SATA connector 6 (optical drive) 22 Internal USB connector 23 PCI-X extender board connector 24 SATA connector 5 (optical drive) 25 USB tape drive connector 26 Diskette drive connector 27 SATA connector 3 (hard drive) 28 SATA connector 1 (hard drive) 29 Pa rallel connector 30 Seria 31 l connector PCI Express expansion slot 3 32 Reserved 33 PCI Express expans
Position Default Function S7 Off Reserved S8 Off Reserved When the system maintenance switch position 6 is set to the On position, the system is prepared to erase all system configuration settings from both CMOS and NVRAM. CAUTION: Clearing CMOS and/or NVRAM deletes configuration information. Be sure to properly configure the server or data loss could occur. For information on emergency ROM backup recovery, refer to ROMPaq disaster recovery (on page 62).
System board LEDs Item LED description Status 1 Processor failure Amber = A multibit error has occurred. Off = Normal 2 PPM failure Amber = PPM has failed. Off = Normal 3 Processor heatsink fan failure Amber = Processor heatsink fan has failed or is missing. Off = Normal 4 Reserved — 5 Reserved — 6 Amber = PCI fan has failed or is missing. PCI fan failure Off = Normal 7 Overtemperature Amber = System has reached a cautionary or critical temperature level.
System LEDs and internal health LED combinations When the internal health LED on the front panel illuminates either amber or red, the server is experiencing a health event. Combinations of illuminated system LEDs and the internal health LED indicate system status. NOTE: The system management driver must be installed for the internal system health LED to provide pre-failure and warranty conditions. The front panel health LEDs indicate only the current hardware status.
PCI-X extender board components Item Description 1 PCI-X expansion slot 1 2 System board connector Fan locations Item Description 1 Rea r fan 2 Processor 3 fan PCI fan (optional) Component identification 73
Specifications Environmental specifications Specification Value Temperature range* Operating 10 Shipping -1 Maximum wet bulb temperature °C to 35°C (50°F to 95°F) 0°C to 60°C (14°F to 140°F) 28°C (82.4°F) Relative humidity (noncondensing)** Operating 20% to 80% Non-operating 20% to 90% * All temperature ratings shown are for sea level. An altitude derating of 1°C per 300 m (1.8°F per 1,000 ft) to 3048 m (10,000 ft) is applicable. No direct sunlight allowed.
Specification Value Maximum peak power 410 W (non-redundant non-hotplug) 430 W (redundant hot-plug) * 100 to 127 VAC is required for 8 A; 200 to 240 VAC is required for 4 A.
Acronyms and abbreviations CMOS complementary metal-oxide semiconductor CSR Customer Self Repair DDR2 double data rate-2 HP SIM HP Systems Insight Manager NMI non-maskable interrupt PCI peripheral component interface PCI Express Peripheral Component Interconnect Express PCI-X peripheral component interconnect extended POST Power-On Self Test PPM processor power module RAID redundant array of inexpensive (or independent) disks RBSU ROM-Based Setup Utility Acronyms and abbreviations 76
SAS serial attached SCSI SATA serial ATA SCSI small computer system interface UID unit identification UPS uninterruptible power system USB universal serial bus Acronyms and abbreviations 77
Index A E access panel 16, 28 additional information 61 air baffle 39 electrostatic discharge 24 environmental specifications 74 expansion boards 50 expansion slots 68, 73 B battery 51, 70 bezel 16, 27 bezel blank 28 bezel key 19 bezel lock 27, 63 bezel, front 16, 28 bezel, removing 27 bezel, tower 27 blanks 16, 28, 29, 30 blue screen event 70 buttons 63, 64 C cables 31, 32, 59, 60 cabling 59, 60 component identification 63, 70 components 16, 19, 63, 66 connectors 63 controller 19 crash dump analysis 7
I iLO (Integrated Lights-Out) 69 IML (Integrated Management Log) 62 Insight Diagnostics 61 Integrated Management Log (IML) 62 internal health LED 72 internal USB connector 68 K keyboard connector 66 L LED, DIMM slot 71, 72 LED, drive activity 64 LED, fan 71, 72 LED, health 64, 72 LED, internal health 64, 72 LED, link/port activity 64, 67 LED, power supply signal 67 LED, processor 71, 72 LED, system power 26, 64 LEDs, front panel 64 LEDs, hard drive 65 LEDs, NIC 67 LEDs, power supply 67 LEDs, PPM failure 7
SATA optical drive 34 serial connector 66, 68 serial number 52 server feet 16, 58 server specifications 74 server, front panel LEDs 64 server, real panel LEDs 67 server, rear panel components 66 spare part numbers 16, 19 specifications, environmental 74 specifications, server 74 static electricity 24 switches 69, 70 system air baffle 16, 39 system battery 19, 68 system board 52, 68 system board battery 51 system board components 68 system board LEDs 71 system components 19 system maintenance switch 68, 69,
