HP ProLiant BL685c Server Blade User Guide October 2006 (First Edition) Part Number 418532-001
© Copyright 2006 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft, Windows, and Windows NT are U.S.
Contents Component identification ............................................................................................................... 6 Front panel components ............................................................................................................................. 6 Front panel LEDs ....................................................................................................................................... 7 SAS and SATA hard drive LEDs.............................
RBSU requirement for Linux deployment............................................................................................ 40 Software drivers and additional components ..................................................................................... 40 HP BladeSystem c-Class Advanced management ............................................................................... 41 Network-based PXE deployment ............................................................................................
POST problems flowchart ............................................................................................................... 64 OS boot problems flowchart ........................................................................................................... 65 Server fault indications flowchart ..................................................................................................... 67 POST error messages and beep codes ............................................................
Component identification In this section Front panel components ............................................................................................................................ 6 Front panel LEDs ...................................................................................................................................... 7 SAS and SATA hard drive LEDs .................................................................................................................
Front panel LEDs Item Description Status 1 UID LED Blue = Identified Blue flashing = Active remote management Off = No active remote management 2 Health LED Green = Normal operation Amber flashing = Degraded condition Red flashing = Critical condition 3 NIC 1 LED* Green = Network linked Green flashing = Network activity Off = No link or activity 4 NIC 2 LED* Green = Network linked Green flashing = Network activity Off = No link or activity 5 NIC 3 LED* Green = Network linked Green flashing
SAS and SATA hard drive LEDs Item Description 1 Fault/UID LED (amber/blue) 2 Online LED (green) SAS and SATA hard drive LED combinations Online/activity LED Fault/UID LED (green) (amber/blue) Interpretation On, off, or flashing Alternating amber and blue The drive has failed, or a predictive failure alert has been received for this drive; it also has been selected by a management application.
Online/activity LED Fault/UID LED (green) (amber/blue) Interpretation Off Steadily amber A critical fault condition has been identified for this drive, and the controller has placed it offline. Replace the drive as soon as possible. Off Amber, flashing regularly (1 Hz) A predictive failure alert has been received for this drive. Replace the drive as soon as possible. Off Off The drive is offline, a spare, or not configured as part of an array.
Item Description 17 Smart Array E200i cache module (under mezzanine card 3) 18 SAS cable 19 Processor socket 1 (populated) 20 DIMM slots (Processor 1 memory banks A and B) 21 System battery 22 DIMM slots (Processor 3 memory banks E and F) 23 Processor socket 3 24 System board thumbscrew 25 System maintenance switch (SW2) 26 Hard drive backplane connector The symbols correspond to the symbols located on the interconnect bays.
Position Function Default 2 Configuration lock Off 3 Reserved Off 4 Reserved Off 5* Password disabled Off 6* Reset configuration Off 7 Reserved Off 8 Reserved Off *To access redundant ROM, set S1, S5, and S6 to ON. System maintenance switch procedures When you perform troubleshooting steps, this guide may instruct you to perform the following procedures: • Clear the system configuration. • Access the redundant ROM.
5. Install the access panel (on page 15). 6. Install the server blade in the enclosure and power up the server blade. 7. After the system beeps, repeat steps 1 through 3. 8. Change positions 1, 5, and 6 of system maintenance switch to off. 9. Repeat steps 5 and 6. If both the current and backup versions of the ROM are corrupt, return the system board for a service replacement. To switch to the backup ROM when the System ROM is not corrupt, use RBSU.
Operations In this section Power up the server blade....................................................................................................................... 13 Power down the server blade .................................................................................................................. 13 Remove the server blade ......................................................................................................................... 14 Remove the access panel ..................
IMPORTANT: When the server blade is in standby mode, auxiliary power is still being provided. To remove all power from the server blade, remove the server blade from the enclosure. After initiating a virtual power down command, be sure that the server blade goes into standby mode by observing that the system power LED is amber. Remove the server blade 1. Identify the proper server blade. 2. Power down the server blade (on page 13). 3. Remove the server blade. 4.
Install the access panel 1. Place the access panel on top of the server blade with the hood latch open. Allow the panel to extend past the rear of the server blade approximately 0.8 cm (0.2 in). 2. Engage the anchoring pin with the corresponding hole in the latch. 3. Push down on the hood latch. The access panel slides to a closed position.
2. Install the access panel (on page 15). 3. Install the server blade ("Installing a server blade" on page 18).
Setup In this section Overview .............................................................................................................................................. 17 Installing an HP BladeSystem c-Class enclosure .......................................................................................... 17 Installing server blade options.................................................................................................................. 17 Installing interconnect modules..............
Interconnect device mapping To support network connections for specific signals, install an interconnect module in the bay corresponding to the embedded NIC or mezzanine signals.
1. Remove the blank. 2. Remove the three adjacent blanks. 3. Slide the device bay shelf locking tab to the left to open it.
4. Push the device bay shelf back until it stops, lift the right side slightly to disengage the two tabs from the divider wall, and then rotate the right edge downward (clockwise). 5. Lift the left side of the device bay shelf to disengage the three tabs from the divider wall, and then remove it from the enclosure.
6. Remove the connector covers. 7. Prepare the server blade for installation.
8. Install the server blade. CAUTION: To prevent improper cooling and thermal damage, do not operate the server blade or the enclosure unless all hard drive and device bays are populated with either a component or a blank. 9. Install blanks in any empty bays: a. Locate the coupler plate that ships with the server blade. b. Install the coupler plate on top of the blank, and then slide the coupler plate forward until it locks into place.
c. Install the second blank onto the tabs on the coupler plate, and then slide the second blank back until it locks into place. d. Install the full-height blank into the device bay. Connecting to the network To connect the HP BladeSystem to a network, each enclosure must be configured with network interconnect devices to manage signals between the server blades and the external network.
Hardware options installation In this section Introduction ........................................................................................................................................... 24 Hot-plug SAS or SATA hard drive option................................................................................................... 24 Processor option..................................................................................................................................... 26 Memory option ..
1. Remove the hard drive blank. 2. Prepare the hard drive.
3. Install the hard drive. 4. Determine the status of the hard drive from the hot-plug hard drive LEDs ("SAS and SATA hard drive LEDs" on page 8). 5. Resume normal server blade operations. Processor option WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: To avoid damage to the system board: • Do not touch the processor socket contacts.
3. Remove the access panel (on page 14). 4. Remove the heatsink blank. Retain the heatsink blank for future use. CAUTION: The pins on the processor socket are very fragile. Any damage to them may require replacing the system board. 5. Remove the processor socket protective cover. Retain the cover for future use. CAUTION: Failure to completely open the processor retaining latch prevents the processor from seating during installation, leading to hardware damage.
6. Open the processor retaining latch and the processor socket retaining bracket. IMPORTANT: Be sure the processor remains inside the processor installation tool. 7. If the processor has separated from the installation tool, carefully re-insert the processor in the tool. 8. Align the processor installation tool with the socket and install the processor.
CAUTION: The processor is designed to fit one way into the socket. Use the alignment guides on the processor and socket to properly align the processor with the socket. 9. Press down firmly until the processor installation tool clicks and separates from the processor, and then remove the processor installation tool.
10. Close the processor retaining bracket and the processor retaining latch. 11. Remove the thermal interface protective cover from the heatsink.
12. Align the holes in the heatsink with the guide pins on the processor cage. CAUTION: Heatsink retaining screws should be tightened in diagonally opposite pairs (in an "X" pattern). 13. Install the heatsink. 14. Install the access panel (on page 15). 15. Install the server blade ("Installing a server blade" on page 18). 16. Power up the server blade (on page 13). Memory option You can expand server memory by installing PC2-5300 Registered DDR2 SDRAM DIMMs.
For DIMM slot locations and bank assignments, see "DIMM slots (on page 10)." Advanced ECC memory Advanced ECC memory is the default memory protection mode for this server blade. In Advanced ECC, the server blade is protected against correctable memory errors. The server blade provides notification if the level of correctable errors exceeds a pre-defined threshold rate. The server blade does not fail because of correctable memory errors.
6. Install the DIMM. 7. Install the DIMM baffle (on page 15). 8. Install the access panel (on page 15). 9. Install the server blade ("Installing a server blade" on page 18). Mezzanine card option Optional mezzanine cards enable network connectivity and provide Fibre Channel support. For mezzanine card locations, see "System board components (on page 9)." For mezzanine card signal mapping, see the HP ProLiant BL685c Server Blade Installation Instructions that ship with the server blade.
4. Remove the mezzanine connector cover. Retain the cover for future use. 5. Install the mezzanine card. Press down above the connector to seat the board. 6. Install the access panel (on page 15). 7. Install the server blade ("Installing a server blade" on page 18). 8. Power up the server blade (on page 13). HP Smart Array E200i Controller battery pack option The optional BBWC enabler provides the system with a means for storing and saving data in the event of an unexpected system shutdown.
CAUTION: After the server blade is powered down, wait 15 seconds and then check the amber LED before removing the battery from the cache module. If the amber LED flashes after 15 seconds, do not remove the battery from the cache module. The cache module is backing up data, and data is lost if the battery is detached before the LED is extinguished. IMPORTANT: The battery pack might have a low charge when installed.
6. Install the Smart Array E200i battery pack on the new cache module provided in the option kit. 7. Install the new Smart Array E200i cache module. 8. Install mezzanine card 3, if necessary. 9. Install the access panel (on page 15). 10. Install the server blade ("Installing a server blade" on page 18). 11. Power up the server blade (on page 13).
Cabling In this section SAS cable routing .................................................................................................................................. 37 Using the local I/O cable........................................................................................................................ 37 Connecting locally to a server blade with video and USB devices ................................................................
Numerous configurations are possible. This section offers two possible configurations. For more information, see "USB support and functionality (on page 52)." Accessing a server blade with local KVM CAUTION: Before disconnecting the local I/O cable from the connector, always squeeze the release buttons on the sides of the connector. Failure to do so can result in damage to the equipment. NOTE: For this configuration, a USB hub is not necessary. To connect additional devices, use a USB hub. 1.
• USB keyboard • USB mouse • USB diskette drive NOTE: Use a USB hub when connecting a USB diskette drive and/or USB CD-ROM drive to the server blade. The USB hub provides additional connections.
Software and configuration utilities In this section Server blade deployment tools ................................................................................................................. 40 Configuration tools ................................................................................................................................. 46 Management tools..................................................................................................................................
For information on how to use these components with a Linux OS, see the HP website (http://h18000.www1.hp.com/products/servers/linux/documentation.html). HP BladeSystem c-Class Advanced management iLO 2 is a standard component of ProLiant c-Class server blades that provides server health and remote server blade manageability. Its features are accessed from a network client device using a supported web browser.
NOTE: Actual NIC numeration depends on several factors, including the OS installed on the server blade. To deploy an OS to multiple server blades, install a PXE deployment server on a network. Deployment infrastructure IMPORTANT: To connect to a network with a Pass-Thru module, always connect the Pass-Thru module to a network device that supports Gigabit speed.
• TCP/IP networking and an IP address compatible with one of the following: the iLO 2 Diagnostic Port IP address or an assigned DHCP or static IP address • CD-ROM drive and/or diskette drive • Any of the following Java™ Runtime Environment versions: 1.3.1_02 1.3.1_07 1.3.1_08 1.4.1 for Windows® users only 1.4.2 for Linux users only Access the Java™ Runtime Environment versions at the HP website (http://java.sun.com/products/archive/index.html).
For more information about the RDP, refer to the HP ProLiant Essentials Rapid Deployment Pack CD or refer to the HP website (http://www.hp.com/servers/rdp). SmartStart Scripting Toolkit The SmartStart Scripting Toolkit is a server deployment product that delivers an unattended automated installation for high-volume server deployments. The SmartStart Scripting Toolkit is designed to support ProLiant BL, ML, and DL servers.
To deploy with a boot CD: 1. Use the local I/O cable to connect a USB CD-ROM drive to the server blade. Refer to "Connecting locally to a server blade with video and USB devices (on page 37)." 2. Insert the boot CD into the USB CD-ROM drive. 3. Reboot the server blade. 4. After the server blade boots, follow the normal installation procedure for an OS. Windows Server™ 2003 cannot be installed from a USB CD-ROM on the I/O cable if the hard drive is completely blank (no partitions defined).
Creating a boot diskette The SmartStart Scripting Toolkit provides the tools and information for creating a boot diskette. For details, refer to the SmartStart Scripting Toolkit User Guide and download the latest version of the software from the HP website (http://www.hp.com/servers/sstoolkit). As an alternative method, configure the hardware manually with RBSU and the iLO 2 remote console. With this method, the disk is more generic and integrates with an existing network OS installation process.
HP ROM-Based Setup Utility RBSU, an embedded configuration utility, performs a wide range of configuration activities that may include: • Configuring system devices and installed options • Displaying system information • Selecting the primary boot controller • Configuring memory options • Language selection For more information on RBSU, refer to the HP ROM-Based Setup Utility User Guide on the Documentation CD or the HP website (http://www.hp.com/servers/smartstart).
For more information, refer to the HP ROM-Based Setup Utility User Guide on the Documentation CD or the HP website (http://www.hp.com/servers/smartstart). Boot options After the auto-configuration process completes, or after the server reboots upon exit from RBSU, the POST sequence runs, and then the boot option screen is displayed. This screen is visible for several seconds before the system attempts to boot from a diskette, CD, or hard drive.
Re-entering the server serial number and product ID After you replace the system board, you must re-enter the server serial number and the product ID. 1. During the server startup sequence, press the F9 key to access RBSU. 2. Select the System Options menu. 3. Select Serial Number. The following warning is displayed: WARNING! WARNING! WARNING! The serial number is loaded into the system during the manufacturing process and should NOT be modified.
Using iLO 2, you can: • Remotely power up, power down, or reboot the host server. • Send alerts from iLO 2 regardless of the state of the host server. • Access advanced troubleshooting features through the iLO 2 interface. • Diagnose iLO 2 using HP SIM through a web browser and SNMP alerting. For more information about iLO 2 features, refer to the iLO 2 documentation on the Documentation CD or on the HP website (http://www.hp.com/servers/lights-out).
HP ProLiant Essentials Virtualization Management Software The ProLiant Essentials Virtual Machine Management Pack and ProLiant Essentials Server Migration Pack plug-ins extend HP Systems Insight Manager capabilities to manage virtual machines.
NOTE: The server ships with the same version programmed on each side of the ROM. Safety and security benefits When you flash the system ROM, ROMPaq writes over the backup ROM and saves the current ROM as a backup, enabling you to switch easily to the alternate ROM version if the new ROM becomes corrupted for any reason. This feature protects the existing ROM version, even if you experience a power failure while flashing the ROM.
For more information or to download the utility, refer to the HP website (http://www.hp.com/servers/diags). Survey Utility Survey Utility, a feature within HP Insight Diagnostics (on page 52), gathers critical hardware and software information on ProLiant server blades. This utility supports operating systems that may not be supported by the server blade. For operating systems supported by the server blade, refer to the HP website (http://www.hp.com/go/supportos).
For more information on ISEE, refer to the HP website (http://www.hp.com/hps/hardware/hw_enterprise.html). To download HP ISEE, visit the HP website (http://www.hp.com/hps/hardware/hw_downloads.html). For installation information, refer to the HP ISEE Client Installation and Upgrade Guide (ftp://ftp.hp.com/pub/services/hardware/info/isee_client.pdf). Web-Based Enterprise Service WEBES enables administrators to manage hardware events proactively, either locally or online.
ProLiant Support Packs PSPs represent operating system-specific bundles of ProLiant optimized drivers, utilities, and management agents. Refer to the PSP website (http://h18000.www1.hp.com/products/servers/management/psp.html). Operating system version support Refer to the operating system support matrix (http://www.hp.com/go/supportos).
Troubleshooting In this section Troubleshooting resources ....................................................................................................................... 56 Pre-diagnostic steps ................................................................................................................................ 56 Service notifications................................................................................................................................ 59 Loose connections .......
Important safety information Familiarize yourself with the safety information in the following sections before troubleshooting the server. Important safety information Before servicing this product, read the Important Safety Information document provided with the server. Symbols on equipment The following symbols may be placed on equipment to indicate the presence of potentially hazardous conditions. This symbol indicates the presence of hazardous energy circuits or electric shock hazards.
subassembly/module-level repair. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard. WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: • The leveling feet are extended to the floor. • The full weight of the rack rests on the leveling feet.
NOTE: To verify the server configuration, connect to the System Management homepage and select Version Control Agent. The VCA gives you a list of names and versions of all installed HP drivers, Management Agents, and utilities, and whether they are up to date. • HP recommends you have access to the server documentation for server-specific information. • HP recommends you have access to the SmartStart CD for value-added software and drivers required during the troubleshooting process.
Start diagnosis flowchart Use the following flowchart to start the diagnostic process.
General diagnosis flowchart The General diagnosis flowchart provides a generic approach to troubleshooting. If you are unsure of the problem, or if the other flowcharts do not fix the problem, use the following flowchart. Item See 1 "Symptom information (on page 58)" 2 "Loose connections (on page 59)" 3 "Service notifications (on page 59)" 4 The most recent version of a particular server or option firmware is available on the following websites: • HP Support website (http://www.hp.
Server blade power-on problems flowchart Symptoms: • The server does not power on. • The system power LED is off or amber. • The health LED is red or amber.
NOTE: For the location of server LEDs and information on their statuses, refer to the server documentation. Possible causes: • Improperly seated or faulty power supply • Loose or faulty power cord • Power source problem • Power on circuit problem • Improperly seated component or interlock problem • Faulty internal component Item See 1 "Component identification (on page 6)" 2 Maintenance and service guides for c-Class server blades, located on the HP website (http://www.hp.
POST problems flowchart Symptoms: • Server does not complete POST NOTE: The server has completed POST when the system attempts to access the boot device.
OS boot problems flowchart There are two ways to use SmartStart when diagnosing OS boot problems on a server blade: • Use iLO to remotely attach virtual devices to mount the SmartStart CD onto the server blade. • Use a local I/O cable and drive to connect to the server blade, and then restart the server blade.
Possible causes: • Corrupted OS • Hard drive subsystem problem • Incorrect boot order setting in RBSU Item See 1 HP ROM-Based Setup Utility User Guide (http://www.hp.com/servers/smartstart) 2 "POST problems flowchart (on page 64)" 3 • "Hard drive problems" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.
* See the server blade OS boot problems flowchart (on page 65) Server fault indications flowchart Symptoms: • Server boots, but a fault event is reported by Insight Management Agents (on page 50) • Server boots, but the internal health LED, external health LED, or component health LED is red or amber NOTE: For the location of server LEDs and information on their statuses, refer to the server documentation.
Possible causes: • Improperly seated or faulty internal or external component • Unsupported component installed • Redundancy failure • System overtemperature condition Item See 1 "Management agents (on page 50)" or in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.com/support) 2 • "Integrated Management Log" or in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.
POST error messages and beep codes For a complete listing of error messages, refer to the "POST error messages" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.com/support). WARNING: To avoid potential problems, ALWAYS read the warnings and cautionary information in the server documentation before removing, replacing, reseating, or modifying system components.
Battery replacement If the server blade no longer automatically displays the correct date and time, you may need to replace the battery that provides power to the real-time clock. Under normal use, battery life is 5 to 10 years. WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled. To reduce the risk of personal injury: • Do not attempt to recharge the battery.
Regulatory compliance notices In this section Regulatory compliance identification numbers ........................................................................................... 71 Federal Communications Commission notice ............................................................................................. 71 Declaration of conformity for products marked with the FCC logo, United States only..................................... 72 Modifications...................................................
Class A equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user’s authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations.
Disposal of waste equipment by users in private households in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
Korean notice Class A equipment Class B equipment Laser compliance This product may be provided with an optical storage device (that is, CD or DVD drive) and/or fiber optic transceiver. Each of these devices contains a laser that is classified as a Class 1 Laser Product in accordance with US FDA regulations and the IEC 60825-1. The product does not emit hazardous laser radiation. Each laser product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.
• • • Do not attempt to recharge the battery. Do not expose the battery to temperatures higher than 60°C (140°F). Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water. Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. To forward them to recycling or proper disposal, please use the public collection system or return them to HP, an authorized HP Partner, or their agents.
Electrostatic discharge In this section Preventing electrostatic discharge............................................................................................................. 77 Grounding methods to prevent electrostatic discharge ................................................................................ 77 Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts.
Specifications In this section Environmental specifications .................................................................................................................... 78 Server specifications ...............................................................................................................................
Technical support In this section Before you contact HP............................................................................................................................. 79 HP contact information............................................................................................................................ 79 Customer Self Repair ..............................................................................................................................
• Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be charged for the travel and labor costs of this service. • Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If, however, you require that HP replace them for you, there may or may not be additional charges, depending on the type of warranty service designated for your product.
Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus d'informations sur ce programme en Amérique du Nord, consultez le site Web HP (http://www.hp.com/go/selfrepair). Riparazione da parte del cliente Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente dal cliente (CSR, Customer Self Repair).
CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag geliefert. Für bestimmte Standorte ist eine Lieferung am selben Tag oder innerhalb von vier Stunden gegen einen Aufpreis verfügbar. Wenn Sie Hilfe benötigen, können Sie das HP technische Support Center anrufen und sich von einem Mitarbeiter per Telefon helfen lassen. Den Materialien, die mit einem CSRErsatzteil geliefert werden, können Sie entnehmen, ob das defekte Teil an HP zurückgeschickt werden muss.
Customer Self Repair Veel onderdelen in HP producten zijn door de klant zelf te repareren, waardoor de reparatieduur tot een minimum beperkt kan blijven en de flexibiliteit in het vervangen van defecte onderdelen groter is. Deze onderdelen worden CSR-onderdelen (Customer Self Repair) genoemd.
Conforme a disponibilidade e o local geográfico, as peças CSR serão enviadas no primeiro dia útil após o pedido. Onde as condições geográficas permitirem, a entrega no mesmo dia ou em quatro horas pode ser feita mediante uma taxa adicional. Se precisar de auxílio, entre em contato com o Centro de suporte técnico da HP para que um técnico o ajude por telefone. A HP especifica nos materiais fornecidos com a peça CSR de reposição se a peça com defeito deve ser devolvida à HP.
Technical support 85
Technical support 86
Acronyms and abbreviations ABEND abnormal end ACU Array Configuration Utility ASR Automatic Server Recovery BBWC battery-backed write cache BIOS Basic Input/Output System CSR Customer Self Repair DDR2 double data rate-2 DHCP Dynamic Host Configuration Protocol DIMM dual inline memory module ESD electrostatic discharge I/O input/output IEC International Electrotechnical Commission Acronyms and abbreviations 87
iLO 2 Integrated Lights-Out 2 IML Integrated Management Log IP Internet Protocol ISEE Instant Support Enterprise Edition KVM keyboard, video, and mouse LED light-emitting diode NBP Network Bootstrap Program NIC network interface controller ORCA Option ROM Configuration for Arrays OSEM Open Services Event Manager POST Power-On Self Test PSP ProLiant Support Pack PXE Preboot Execution Environment RAID redundant array of inexpensive (or independent) disks Acronyms and abbreviations 88
RBSU ROM-Based Setup Utility RDP Rapid Deployment Pack ROM read-only memory SAS serial attached SCSI SATA serial ATA SCSI small computer system interface SFP small form-factor pluggable SIM Systems Insight Manager SNMP Simple Network Management Protocol TCP/IP Transmission Control Protocol/Internet Protocol TFTP Trivial File Transfer Protocol UID unit identification USB universal serial bus VCA Version Control Agent Acronyms and abbreviations 89
WEBES Web-Based Enterprise Service WfM Wired for Management Acronyms and abbreviations 90
Index A access panel 14, 15 ACU (Array Configuration Utility) 48 ADU (Array Diagnostic Utility) 53 Advanced ECC memory 32 ASR (Automatic Server Recovery) 49 auto-configuration process 47 Autorun menu 46 B batteries, replacing 70, 75 battery 70, 75 battery replacement notice 70, 75 battery-backed write cache enabler 34 beep codes 69 BIOS Serial Console 48 BIOS upgrade 49 BSMI notice 74 buttons 6 buttons, front panel 6 C cables 37, 59, 73 cabling 37 Canadian notice 73 Care Pack 55 component identification 6
I identification number 71 iLO 2 (Integrated Lights-Out 2) 13, 40, 49 IML (Integrated Management Log) 53 Important Safety Information document 57 Insight Diagnostics 52 installation, server blade 18 installation, server options 24 installing the access panel 15 Integrated Management Log (IML) 53 interconnect modules 17 internal USB connector 52 J Japanese notice 74 K Korean notices 75 L laser devices 75 LED, health 7 LED, power button 7 LED, system power 7 LED, UID 7 LEDs 6, 7, 8 LEDs, front panel 7 LEDs
SmartStart autorun menu 46 SmartStart Scripting Toolkit 44 SmartStart, overview 46 specifications 78 start diagnosis flowchart 60 static electricity 77 support 53, 79 support packs 46 supported operating systems 55 Survey Utility 53 switches, interconnect 17 symbols on equipment 57 system board battery 75 system board components 9 System Erase Utility 50 system maintenance switch 10 Systems Insight Manager 50 T Taiwan battery recycling notice 76 technical support 79 telephone numbers 79 troubleshooting 56
