HP ProLiant BL680c Generation 5 Server Blade User Guide Part Number 452661-002 October 2007 (Second Edition)
© Copyright 2007 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation.
Contents Component identification ............................................................................................................... 6 Front panel components ............................................................................................................................. 6 Front panel LEDs ....................................................................................................................................... 7 SAS and SATA hard drive LEDs.............................
Array controller cabling ........................................................................................................................... 40 Smart Array Controller cabling to a battery pack ............................................................................... 41 Smart Array Controller cabling to a SAS controller ............................................................................ 41 Software and configuration utilities ...........................................................
Prepare the server for diagnosis ...................................................................................................... 64 Service notifications................................................................................................................................. 65 Loose connections ................................................................................................................................... 65 Troubleshooting flowcharts .......................................
Component identification Front panel components Item Description 1 Local I/O cable connector* 2 Power On/Standby button 3 Serial pull tab 4 Server blade handle release button 5 Server blade handle 6 Hard drive bay 1 7 Hard drive bay 2 * The local I/O cable connector is used with the local I/O cable to perform some server blade configuration and diagnostic procedures.
Front panel LEDs Item Description Status 1 UID LED Blue = Identified Blue flashing = Active remote management Off = No active remote management 2 Health LED Green = Normal operation Amber flashing = Degraded condition Red flashing = Critical condition 3 NIC 1 LED* Green = Network linked Green flashing = Network activity Off = No link or activity 4 NIC 2 LED* Green = Network linked Green flashing = Network activity Off = No link or activity 5 NIC 3 LED* Green = Network linked Green flashing
SAS and SATA hard drive LEDs Item Description 1 Fault/UID LED (amber/blue) 2 Online LED (green) SAS and SATA hard drive LED combinations Online/activity LED (green) Fault/UID LED (amber/blue) Interpretation On, off, or flashing Alternating amber and blue The drive has failed, or a predictive failure alert has been received for this drive; it also has been selected by a management application.
Online/activity LED (green) Fault/UID LED (amber/blue) Interpretation Flashing irregularly Amber, flashing regularly (1 Hz) The drive is active, but a predictive failure alert has been received for this drive. Replace the drive as soon as possible. Flashing irregularly Off The drive is active, and it is operating normally. Off Steadily amber A critical fault condition has been identified for this drive, and the controller has placed it offline. Replace the drive as soon as possible.
Item Description 8 Embedded NICs 9 FBDIMM slots (1-8) 10 Internal USB connector 11 Smart Array P400i cache module connector 12 System maintenance switch (SW3) 13 System battery The symbols correspond to the symbols located on the interconnect bays. For more information, see the HP ProLiant BL680c Generation 5 Server Blade Installation Instructions that ship with the server blade. Mezzanine connector definitions PCIe x8 mezzanine connectors support x16 cards at up to x8 speeds.
Position Function Default 4 Reserved Off 5* Password disabled Off 6* Reset configuration Off 7 Reserved Off 8 Reserved Off *To access redundant ROM, set S1, S5, and S6 to ON. System maintenance switch procedures When you perform troubleshooting steps, this guide may instruct you to perform the following procedures: • Clear the system configuration. • Access the redundant ROM. To complete these procedures, you must change physical settings on the system maintenance switch.
3. Remove the access panel (on page 14). 4. Change positions 1, 5, and 6 of the system maintenance switch to on. 5. Install the access panel (on page 15). 6. Install the server blade in the enclosure and power up the server blade. 7. After the system beeps, repeat steps 1 through 3. 8. Change positions 1, 5, and 6 of system maintenance switch to off. 9. Repeat steps 5 and 6. If both the current and backup versions of the ROM are corrupt, return the system board for a service replacement.
Operations Power up the server blade The Onboard Administrator initiates an automatic power-up sequence when the server blade is installed. If the default setting is changed, use one of the following methods to power up the server blade: • Use a virtual power button selection through iLO 2. • Press and release the Power On/Standby button. When the server blade goes from the standby mode to the full power mode, the system power LED changes from amber to green.
Remove the server blade 1. Identify the proper server blade. 2. Power down the server blade (on page 13). 3. Remove the server blade. 4. Place the server blade on a flat, level work surface. WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: To prevent damage to electrical components, properly ground the server blade before beginning any installation procedure. Improper grounding can cause ESD.
Install the access panel 1. Place the access panel on top of the server blade with the hood latch open. Allow the panel to extend past the rear of the server blade approximately 0.8 cm (0.2 in). 2. Engage the anchoring pin with the corresponding hole in the latch. 3. Push down on the hood latch. The access panel slides to a closed position.
o FBDIMM baffle covering FBDIMM slots 9-16 Install the FBDIMM baffle CAUTION: To avoid damage to the server blade and the enclosure, install all FBDIMM baffles in the proper location after adding or replacing FBDIMMs. FBDIMM baffles that are missing or installed incorrectly can compromise server blade and enclosure cooling. 1.
o FBDIMM baffle covering FBDIMM slots 9-16 2. Install the access panel (on page 15). 3. Install the server blade ("Installing a server blade" on page 19).
Setup Overview Installation of a server blade requires the following steps: 1. Install and configure an HP BladeSystem c-Class enclosure. 2. Install any server blade options. 3. Install interconnect modules in the enclosure. 4. Connect the interconnect modules to the network. 5. Install a server blade. 6. Complete the server blade configuration. Installing an HP BladeSystem c-Class enclosure Before performing any server blade-specific procedures, install an HP BladeSystem c-Class enclosure.
Installation is shown in the HP BladeSystem c7000 Enclosure. Server blade signal Interconnect bay NIC 1 (Embedded) 1 NIC 2 (Embedded) 2 NIC 3 (Embedded) 1 NIC 4 (Embedded) 2 Mezzanine 1 3 and 4 Mezzanine 2 5 and 6 Interconnect bay labels 7 and 8 Mezzanine 3 7 and 8 5 and 6 For detailed port mapping information, see the HP BladeSystem enclosure quick setup guide or the HP BladeSystem enclosure setup and installation guide on the HP website (http://www.hp.com/go/bladesystem/documentation).
Enclosure documentation is located at the HP website (http://h71028.www7.hp.com/enterprise/cache/80316-0-0-0-121.html). Server blade documentation is located at the HP website (http://h18004.www1.hp.com/products/servers/platforms/). To install a server blade: 1. Remove the blank. 2. Remove the three adjacent blanks. 3. Slide the device bay shelf locking tab to the left to open it.
4. Push the device bay shelf back until it stops, lift the right side slightly to disengage the two tabs from the divider wall, and then rotate the right edge downward (clockwise). 5. Lift the left side of the device bay shelf to disengage the three tabs from the divider wall, and then remove it from the enclosure.
6. Remove the connector covers. 7. Prepare the server blade for installation.
8. Install the server blade. CAUTION: To prevent improper cooling and thermal damage, do not operate the server blade or the enclosure unless all hard drive and device bays are populated with either a component or a blank. 9. Install blanks in any empty bays. For more information, see the enclosure setup and installation guide.
Hardware options installation Introduction If more than one option is being installed, read the installation instructions for all the hardware options and identify similar steps to streamline the installation process. WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: To prevent damage to electrical components, properly ground the server before beginning any installation procedure.
2. Prepare the hard drive. 3. Install the hard drive. 4. Determine the status of the hard drive from the hot-plug hard drive LEDs ("SAS and SATA hard drive LEDs" on page 8). 5. Resume normal server blade operations. Processor option WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: To avoid damage to the system board: • Do not touch the processor socket contacts.
CAUTION: To avoid damage to the processor: • Handle the processor only by the edges. • Do not touch the bottom of the processor, especially the contact area. CAUTION: To prevent possible server malfunction and damage to the equipment, multiprocessor configurations must contain processors with the same part number. CAUTION: To prevent possible server blade overheating, always populate processor sockets with a processor and a heatsink or a heatsink blank.
7. Open the processor locking lever. CAUTION: The processor is designed to fit one way into the socket. Use the alignment guides on the processor and socket to properly align the processor with the socket. 8. Install the processor. 9. Close the processor locking lever.
10. Remove the thermal interface protective cover from the heatsink. CAUTION: Heatsink retaining screws should be tightened in diagonally opposite pairs (in an "X" pattern). 11. Install the heatsink. 12. Install the access panel (on page 15). 13. Install the server blade ("Installing a server blade" on page 19). 14. Power up the server blade (on page 13). Memory option This server blade contains 16 memory expansion slots. To expand server blade memory, install 667MHz DDR2 FBDIMMs.
CAUTION: Use only HP FBDIMMs. FBDIMMs from other sources may adversely affect data integrity. Memory configurations The server blade supports the following AMP options to optimize server blade availability: • Advanced ECC supporting up to 64 GB of active memory using 4-GB FBDIMMs. • Online Spare Memory supporting up to 56 GB of active memory and 8 GB of online spare memory using 4-GB FBDIMMs. Online Spare Memory provides additional protection against degrading memory.
• FBDIMMs must be installed in sequential order, beginning with bank A.
In addition to general configuration requirements, all populated banks on a branch must contain FBDIMMs with identical part numbers.
Configuration Bank A Bank B Bank C Bank D Bank E Bank F Bank G Bank H Branch 0 Branch 1 Branch 0 Branch 1 Branch 0 Branch 1 Branch 0 Branch 1 1A, 5A 9B, 13B 2C, 6C 10D, 14D 3E, 7E 11F, 15F 4G, 8G 12H, 16H 1 X X — — — — — — 2 X X X X — — — — 3 X X X X X X — — 4 X X X X X X X X After installing FBDIMMs, use RBSU to configure the system for mirrored memory support ("Configuring mirrored memory" on page 51).
Mezzanine card option Optional mezzanine cards enable network connectivity and provide Fibre Channel support. For mezzanine card locations, see "System board components (on page 9)." Optional mezzanine cards are classified as Type I mezzanine cards and Type II mezzanine cards. The card type determines where it can be installed in the server blade: • Install Type I mezzanine cards on any mezzanine connector. • Install Type II mezzanine cards only on Mezzanine 2 connector or Mezzanine 3 connector.
5. Install the mezzanine card. Press down above the connector to seat the board. 6. Install the access panel (on page 15). 7. Install the server blade ("Installing a server blade" on page 19). 8. Power up the server blade (on page 13). Cache module and battery pack option The optional BBWC enabler provides the system with a means for storing and saving data in the event of an unexpected system shutdown. To install the component: 1. Back up all data on the hard drive. 2.
5. Remove the FBDIMM baffle. 6. Remove the cache module that shipped with the server.
7. Connect the battery cable to the cache module that shipped with the option kit. 8. Install the cache module. 9. Install the FBDIMM baffle (on page 16).
10. Install the battery pack on the FBDIMM baffle. 11. Connect and route the battery cable. 12. Install the access panel (on page 15). 13. Install the server blade ("Installing a server blade" on page 19).
Cabling Using the local I/O cable The local I/O cable enables the user to perform server blade administration, configuration, and diagnostic procedures by connecting video and USB devices directly to the server blade. For local I/O cable connectors, see "Local I/O cable (on page 12).
4. Connect a USB keyboard to the second USB connector. Item Description 1 Monitor 2 USB mouse 3 Local I/O cable 4 Server blade 5 Video connector 6 USB keyboard Accessing local media devices Use the following configuration when configuring a server blade or loading software updates and patches from a USB CD/DVD-ROM or a USB diskette. 1. Connect the local I/O cable to the server blade. 2. Connect the video connector to a monitor. 3. Connect a USB hub to one USB connector. 4.
Item Description 1 Monitor 2 USB mouse 3 Local I/O cable 4 Server blade 5 USB hub 6 USB keyboard 7 USB CD/DVD-ROM drive or diskette drive Array controller cabling Depending on the primary controller installed, various cabling configurations exist: • PCI Smart Array controller cabling to a battery pack • PCI Smart Array controller cabling to a SAS controller Cabling 40
Smart Array Controller cabling to a battery pack Smart Array Controller cabling to a SAS controller Cabling 41
Software and configuration utilities Server blade deployment tools RBSU requirement for Linux deployment To properly install some versions of the Linux x64 operating system, the Linux x64 HPET Workaround selection in RBSU must be enabled. If this step is not performed, a kernel panic can occur during boot.
HP BladeSystem c-Class Advanced management iLO 2 is a standard component of ProLiant c-Class server blades that provides server health and remote server blade manageability. Its features are accessed from a network client device using a supported web browser. In addition to other features, iLO 2 provides remote keyboard, mouse, and video (text and graphics) capability for a server blade, regardless of the state of the host OS or host server blade.
be designated for PXE in RBSU. For NIC connector locations, refer to the documentation included with the server blade. NOTE: Actual NIC numeration depends on several factors, including the OS installed on the server blade. To deploy an OS to multiple server blades, install a PXE deployment server on a network. Deployment infrastructure IMPORTANT: To connect to a network with a Pass-Thru module, always connect the Pass-Thru module to a network device that supports Gigabit speed.
• o 10-Mb/s network adapter o CD-ROM drive Windows® repository server (Windows® or Linux deployment) o Windows® 2000 or Windows Server™ 2003 OS installed o Network connection o CD-ROM drive o 1.5 GB of available disk space o TCP/IP networking and an IP address compatible with one of the following: the iLO 2 Diagnostic Port IP address or an assigned DHCP or static IP address o CD-ROM drive and/or diskette drive o Any of the following Java™ Runtime Environment versions: 1.3.1_02 1.3.1_07 1.
A number of third-party PXE deployment tools are available for Windows® and Linux. For additional information, refer to the HP website (ftp://ftp.compaq.com/pub/products/servers/management/pxe_wp.pdf). HP ProLiant Essentials Rapid Deployment Pack NOTE: To deploy server blades in an existing server blade enclosure, always use the most recent version of RDP available at the HP website (http://www.hp.com/servers/rdp). The RDP software is the preferred method for rapid, high-volume server deployments.
o Use iLO 2 to create an image file of the boot CD. o Copy the image of the boot CD to a location on the network or the client PC hard drive. 2. Remotely access the server blade through iLO 2. Refer to "HP BladeSystem c-Class advanced management (on page 43)." 3. Click the Virtual Devices tab. 4. Select Virtual Media. 5. Use the Virtual Media applet to select the local CD or image file and connect the Virtual CD to the server blade. 6.
• iLO virtual floppy (on page 48) • PXE ("PXE deployment" on page 45) iLO virtual floppy To deploy with a boot diskette: 1. Do one of the following: o Insert the boot diskette into the client PC that is using the iLO 2 Remote Console. o Use iLO 2 to create an image file of the boot diskette. o Copy the image of the boot diskette to a location on the network or the client PC hard drive. 2. Remotely access the server blade through iLO 2.
• Testing server hardware using the Insight Diagnostics Utility ("HP Insight Diagnostics" on page 57) • Installing software drivers directly from the CD. With systems that have internet connection, the SmartStart Autorun Menu provides access to a complete list of ProLiant system software. • Enabling access to the Array Configuration Utility (on page 52), Array Diagnostic Utility (on page 58), and Erase Utility (on page 54) SmartStart is included in the HP ProLiant Essentials Foundation Pack.
IMPORTANT: RBSU automatically saves settings when you press the Enter key. The utility does not prompt you for confirmation of settings before you exit the utility. To change a selected setting, you must select a different setting and press the Enter key.
• Force a PXE Network boot by pressing the F12 key BIOS Serial Console BIOS Serial Console allows you to configure the serial port to view POST error messages and run RBSU remotely through a serial connection to the server COM port. The server that you are remotely configuring does not require a keyboard and mouse. For more information about BIOS Serial Console, see the BIOS Serial Console User Guide on the Documentation CD or the HP website (http://www.hp.com/support/smartstart/documentation).
3. Select System Options. 4. Select Advanced Memory Protection. 5. Select Online Spare with Advanced ECC Support. 6. Press the Enter key. 7. Press the Esc key to exit the current menu, or press the F10 key to exit RBSU. For more information on online spare memory, refer to the white paper on the HP website (http://h18000.www1.hp.com/products/servers/technology/memoryprotection.html).
Re-entering the server serial number and product ID After you replace the system board, you must re-enter the server serial number and the product ID. 1. During the server startup sequence, press the F9 key to access RBSU. 2. Select the System Options menu. 3. Select Serial Number. The following warning is displayed: WARNING! WARNING! WARNING! The serial number is loaded into the system during the manufacturing process and should NOT be modified.
iLO 2 Standard Blade Edition technology The iLO 2 subsystem is a standard component of selected ProLiant servers that provides server health and remote server manageability. The iLO 2 subsystem includes an intelligent microprocessor, secure memory, and a dedicated network interface. This design makes iLO 2 independent of the host server and its operating system. The iLO 2 subsystem provides remote access to any authorized network client, sends alerts, and provides other server management functions.
For additional information, refer to the Management CD in the HP ProLiant Essentials Foundation Pack or the HP SIM website (http://www.hp.com/go/hpsim). Management Agents Management Agents provide the information to enable fault, performance, and configuration management. The agents allow easy manageability of the server through HP SIM software, and thirdparty SNMP management platforms. Management Agents are installed with every SmartStart assisted installation or can be installed through the HP PSP.
HP Insight Control Environment Suites HP Insight Control Environment and Insight Control Environment for BladeSystem are integrated suites of software that simplify the management of HP infrastructures. The HP Insight Control Environment suites are licensing options for HP infrastructure management software delivered on the Insight Control Management DVD.
USB support and functionality USB support HP provides both standard USB support and legacy USB support. Standard support is provided by the OS through the appropriate USB device drivers. Before the OS loads, HP provides support for USB devices through legacy USB support, which is enabled by default in the system ROM. HP hardware supports USB version 2.0. Legacy USB support provides USB functionality in environments where USB support is normally not available.
HP Insight Diagnostics survey functionality HP Insight Diagnostics (on page 57) provides survey functionality that gathers critical hardware and software information on ProLiant server blades. This functionality supports operating systems that may not be supported by the server blade. For operating systems supported by the server blade, see the HP website (http://www.hp.com/go/supportos).
identify and prevent potential critical problems. Through remote diagnostic scripts and vital system configuration information collected about your systems, ISEE enables fast restoration of your systems. Install ISEE on your systems to help mitigate risk and prevent potential critical problems. For more information on ISEE, refer to the HP website (http://www.hp.com/hps/hardware/hw_enterprise.html). To download HP ISEE, visit the HP website (http://www.hp.com/hps/hardware/hw_downloads.html).
ProLiant Support Packs PSPs represent operating system-specific bundles of ProLiant optimized drivers, utilities, and management agents. Refer to the PSP website (http://h18000.www1.hp.com/products/servers/management/psp.html). Operating system version support Refer to the operating system support matrix (http://www.hp.com/go/supportos).
Battery replacement If the server blade no longer automatically displays the correct date and time, you may need to replace the battery that provides power to the real-time clock. Under normal use, battery life is 5 to 10 years. WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled. To reduce the risk of personal injury: • Do not attempt to recharge the battery.
Troubleshooting Troubleshooting resources NOTE: For common troubleshooting procedures, the term "server" is used to mean servers and server blades. The HP ProLiant Servers Troubleshooting Guide provides simple procedures for resolving common problems as well as a comprehensive course of action for fault isolation and identification, error message interpretation, issue resolution, and software maintenance.
Important safety information Before servicing this product, read the Important Safety Information document provided with the server. Symbols on equipment The following symbols may be placed on equipment to indicate the presence of potentially hazardous conditions. This symbol indicates the presence of hazardous energy circuits or electric shock hazards. Refer all servicing to qualified personnel. WARNING: To reduce the risk of injury from electric shock hazards, do not open this enclosure.
WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: • The leveling feet are extended to the floor. • The full weight of the rack rests on the leveling feet. • The stabilizing feet are attached to the rack if it is a single-rack installation. • The racks are coupled together in multiple-rack installations. • Only one component is extended at a time. A rack may become unstable if more than one component is extended for any reason.
NOTE: To verify the server configuration, connect to the System Management homepage and select Version Control Agent. The VCA gives you a list of names and versions of all installed HP drivers, Management Agents, and utilities, and whether they are up to date. o HP recommends you have access to the server documentation for server-specific information. o HP recommends you have access to the SmartStart CD for value-added software and drivers required during the troubleshooting process.
• Server blade power-on problems flowchart (on page 69) • POST problems flowchart (on page 71) • OS boot problems flowchart (on page 73) • Server fault indications flowchart (on page 75) Start diagnosis flowchart Use the following flowchart to start the diagnostic process.
General diagnosis flowchart The General diagnosis flowchart provides a generic approach to troubleshooting. If you are unsure of the problem, or if the other flowcharts do not fix the problem, use the following flowchart.
Item See 4 The most recent version of a particular server or option firmware is available on the following websites: • HP Support website (http://www.hp.com/support) • HP ROM-BIOS/Firmware Updates website (http://h18023.www1.hp.com/support/files/server/us/romflash.ht ml) 5 "General memory problems are occurring" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.
Server blade power-on problems flowchart Symptoms: • The server does not power on. • The system power LED is off or amber.
• The health LED is red or amber. NOTE: For the location of server LEDs and information on their statuses, refer to the server documentation.
POST problems flowchart Symptoms: • Server does not complete POST NOTE: The server has completed POST when the system attempts to access the boot device.
Item Refer to 1 Server blade power-on problems flowchart (on page 69) 2 "POST error messages and beep codes (on page 77)" 3 "Video problems" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.com/support) 4 "Symptom information (on page 64)" 5 "General memory problems are occurring" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.
OS boot problems flowchart There are two ways to use SmartStart when diagnosing OS boot problems on a server blade: • Use iLO to remotely attach virtual devices to mount the SmartStart CD onto the server blade. • Use a local I/O cable and drive to connect to the server blade, and then restart the server blade.
Possible causes: • Corrupted OS • Hard drive subsystem problem • Incorrect boot order setting in RBSU Item See 1 HP ROM-Based Setup Utility User Guide (http://www.hp.com/servers/smartstart) 2 "POST problems flowchart (on page 71)" 3 • "Hard drive problems" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.
* See the server blade OS boot problems flowchart (on page 73) Server fault indications flowchart Symptoms: • Server boots, but a fault event is reported by Insight Management Agents (on page 55) • Server boots, but the internal health LED, external health LED, or component health LED is red or amber Troubleshooting 75
NOTE: For the location of server LEDs and information on their statuses, refer to the server documentation. Possible causes: • Improperly seated or faulty internal or external component • Unsupported component installed • Redundancy failure • System overtemperature condition Item See 1 "Management agents (on page 55)" or in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.
POST error messages and beep codes For a complete listing of error messages, refer to the "POST error messages" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.com/support).
Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number. The regulatory model number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this regulatory model number.
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Canadian notice (Avis Canadien) Class A equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Class B equipment This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Disposal of waste equipment by users in private households in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
Korean notice Class A equipment Class B equipment Battery replacement notice WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled. To reduce the risk of personal injury: • Do not attempt to recharge the battery. • Do not expose the battery to temperatures higher than 60°C (140°F).
Power cord statement for Japan Regulatory compliance notices 83
Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent electrostatic damage: • Avoid hand contact by transporting and storing products in static-safe containers.
Specifications Environmental specifications Specification Value Temperature range* Operating 10°C to 35°C (50°F to 95°F) Shipping -40°C to 60°C (-40°F to 140°F) Storage -20°C to 60°C (-4°F to 140°F) Maximum wet bulb temperature 30°C (86°F) Relative humidity (noncondensing)** Operating 10% to 90% Shipping 10% to 90% Storage 10% to 95% * All temperature ratings shown are for sea level. An altitude derating of 1°C per 304.8 m (1.8°F per 1,000 ft) to 3048 m (10,000 ft) is applicable.
Technical support Before you contact HP Be sure to have the following information available before you call HP: • Technical support registration number (if applicable) • Product serial number • Product model name and number • Product identification number • Applicable error messages • Add-on boards or hardware • Third-party hardware or software • Operating system type and revision level HP contact information For the name of the nearest HP authorized reseller: • In the United States, see
• Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be charged for the travel and labor costs of this service. • Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If, however, you require that HP replace them for you, there may or may not be additional charges, depending on the type of warranty service designated for your product.
l'ensemble des frais d'expédition et de retour, et détermine la société de courses ou le transporteur à utiliser. Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus d'informations sur ce programme en Amérique du Nord, consultez le site Web HP (http://www.hp.com/go/selfrepair).
lassen möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen Garantiebedingungen zusätzliche Kosten anfallen. HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet. CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag geliefert.
de envío. Si no enviara el componente defectuoso requerido, HP podrá cobrarle por el de sustitución. En el caso de todas sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes y escogerá la empresa de transporte que se utilice para dicho servicio. Para obtener más información acerca del programa de Reparaciones del propio cliente de HP, póngase en contacto con su proveedor de servicios local.
• Obrigatória – Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço. • Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto.
Technical support 92
Technical support 93
Acronyms and abbreviations ABEND abnormal end ACU Array Configuration Utility ASR Automatic Server Recovery BBWC battery-backed write cache BIOS Basic Input/Output System CSR Customer Self Repair DDR2 double data rate-2 DHCP Dynamic Host Configuration Protocol ESD electrostatic discharge FBDIMM fully buffered DIMM I/O input/output IEC International Electrotechnical Commission Acronyms and abbreviations 94
iLO 2 Integrated Lights-Out 2 IML Integrated Management Log IP Internet Protocol ISEE Instant Support Enterprise Edition KVM keyboard, video, and mouse LED light-emitting diode NBP Network Bootstrap Program NIC network interface controller ORCA Option ROM Configuration for Arrays OSEM Open Services Event Manager POST Power-On Self Test PSP ProLiant Support Pack PXE Preboot Execution Environment RAID redundant array of inexpensive (or independent) disks Acronyms and abbreviations 95
RBSU ROM-Based Setup Utility RDP Rapid Deployment Pack ROM read-only memory SAS serial attached SCSI SATA serial ATA SCSI small computer system interface SFP small form-factor pluggable SIM Systems Insight Manager SNMP Simple Network Management Protocol TCP/IP Transmission Control Protocol/Internet Protocol TFTP Trivial File Transfer Protocol UID unit identification USB universal serial bus VCA Version Control Agent Acronyms and abbreviations 96
WEBES Web-Based Enterprise Service WfM Wired for Management Acronyms and abbreviations 97
Index A access panel 14, 15 ACU (Array Configuration Utility) 52 ADU (Array Diagnostic Utility) 58 ASR (Automatic Server Recovery) 53 auto-configuration process 50 Autorun menu 48 B batteries, replacing 61, 82 battery 61, 82 battery replacement notice 61, 82 battery-backed write cache enabler 34 beep codes 77 BIOS Serial Console 51 BIOS upgrade 53 BSMI notice 81 buttons 6 buttons, front panel 6 C cables 38, 40, 41, 65, 79 cabling 38 Canadian notice 80 Care Pack 60 component identification 6, 8, 9 componen
I N identification number 78 iLO 2 (Integrated Lights-Out 2) 13, 42, 54 IML (Integrated Management Log) 58 Important Safety Information document 62 Insight Diagnostics 57, 58 installation, server options 24 installing the access panel 15 Integrated Management Log (IML) 58 interconnect devices 18 interconnect modules 18 internal USB connector 57 network connection problems 23 J Japanese notice 81 K Korean notices 82 KVM 38 L LED, health 7, 8 LED, power button 7 LED, system power 7 LED, UID 7 LEDs 6 LED
serial label pull tab 6 serial number 53 series number 78 server blade handle 6 server fault indications flowchart 75 server features and options 24 service notifications 65 SmartStart autorun menu 48 SmartStart Scripting Toolkit 46 SmartStart, overview 48 specifications 85 start diagnosis flowchart 66 static electricity 84 support 58, 86 support packs 48 supported operating systems 60 switches, interconnect 18 symbols on equipment 63 system board battery 82 system board components 9 System Erase Utility 54
