HP MSM SNMP MIB Reference Guide 5400zl HP MSMSwitches SNMP MIB Installation and Getting Started Guide Reference Guide
HP MSM SNMP MIB Reference Guide
Copyright and Disclaimer Notices © Copyright 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of Hewlett-Packard.
Contents 1 Introduction About this guide ...........................................................................................................1-2 Products covered...................................................................................................1-2 Important terms .....................................................................................................1-3 Conventions ...........................................................................................................
3 MIB descriptions Introduction ..................................................................................................................3-3 COLUBRIS-DEVICE-EVENT-MIB ..............................................................................3-3 COLUBRIS-DEVICE-DOT1X-MIB ..............................................................................3-6 COLUBRIS-DEVICE-WIRELESS-MIB........................................................................3-8 COLUBRIS-WIRELESS-CLIENT-MIB .............
COLUBRIS-CONTROLLER-MIB...............................................................................3-86 COLUBRIS-CONNECTION-LIMITING-MIB ............................................................3-87 HP-WLAN-SFLOW-EXTENSIONS-MIB....................................................................3-88 COLUBRIS-CLIENT-TRACKING-MIB......................................................................3-89 HP-WLAN-NEIGHBORHOOD-MIB ..........................................................................
vi
Chapter 1: Introduction 1 Introduction Contents About this guide ...........................................................................................................1-2 Products covered...................................................................................................1-2 Important terms .....................................................................................................1-3 Conventions ...................................................................................
Introduction About this guide About this guide This guide provides an overview of the HP SNMP implementation and detailed information on all supported MIB objects.
Introduction About this guide “WW” identifies worldwide regions not otherwise explicitly named. Note All references to the MSM320 also apply to the MSM325. All references to the MSM466 also apply to the MSM466-R. Important terms The following terms are used in this guide. Term Description AP MSM AP These terms are used interchangeably to refer to any HP MSM3xx or MSM4xx Access Point, or the MSM317 Access Device. Non-HP access points are identified as third-party APs.
Introduction HP Networking support Management tool This guide uses specific syntax when directing you to interact with the management tool user interface. Key user-interface elements are identified as follows. On APs: Example directions in this guide What to do in the user interface Select Wireless > Local Mesh. On the main menu select Wireless and then select Local mesh on the sub-menu. For Password, specify secret22. In the field Password enter the text secret22 exactly as shown.
Introduction Online documentation Online documentation You can download documentation from the HP Support Website at: www.hp.com/support/manuals. Search by product name or part number.
Introduction Configuring SNMP options Configuring SNMP options SNMP options are configured as follows: On an MSM AP, select Management > SNMP. On an MSM Controller, select Controller >> Management > SNMP. By default, the SNMP agent is enabled (SNMP agent configuration in title bar is checked). If you disable the agent, the device will not respond to SNMP requests. For example: (The configuration page for an MSM720 is shown.
Introduction Configuring SNMP options The following sections use the term device to refer to any MSM Controller or MSM AP. Attributes System name Specify a name to identify the controller. By default, this is set to the serial number of the controller. Location Specify a descriptive name for the location where the controller is installed. Contact Contact information for the controller. Port Specify the UDP port and protocol the controller uses to respond to SNMP requests. Default port is 161.
Introduction Configuring SNMP options v3 users This table lists all defined SNMP v3 users. To add a new user, select Add New User. Up to five users are supported. To edit a user, select its link in the Username column. Username The SNMP v3 username. Security Security protocol defined for the user. Authentication type and encryption type are separated by a slash. For example, MD5/DES indicates MD5 authentication and DES encryption.
Introduction Standard MIBs Standard MIBs Standard MIB II objects are supported as follows: MIB MSM Controllers MSM APs IEEE8021-PAE-MIB ✓ ✓ RADIUS-AUTH-CLIENT-MIB ✓ - RADIUS-ACC-CLIENT-MIB ✓ - RADIUS-AUTH-SERVER-MIB ✓ - IF-MIB ✓ ✓ BRIDGE-MIB - ✓ IP-MIB ✓ ✓ TCP-MIB ✓ ✓ UDP-MIB ✓ ✓ SNMPV2-MIB ✓ ✓ SNMP-FRAMEWORK-MIB ✓ ✓ SFLOW-MIB5 ✓ ✓ LLDP-EXT-DOT3-MIB ✓ ✓ (controlled mode only) LLDP-MIB ✓ ✓ (controlled mode only) The following restrictions apply to the support of
Introduction Standard MIBs Group OID Support IF ifAdminStatus (up=1, down=2) Read-Write ifLastChange Not Supported ifInUnknownProtos ifInNUcastPkts ifOutNUcastPkts ifInMulticastPkts (Always = 0) ifInBroadcastPkts (Always = 0) ifOutMulticastPkts (Always = 0) ifOutBroadcastPkts (Always = 0) ifHCInUcastPkts (Always = 0) ifHCInMulticastPkts (Always = 0) ifHCInBroadcastPkts (Always = 0) ifHCOutUcastPkts (Always = 0) ifHCOutMulticastPkts (Always = 0) ifHCOutBroadcastPkts (Always = 0) ifLinkUpDownTrapEnab
Introduction Enterprise MIBs Group OID Support IP ipForwarding Read-Only ipDefaultTTL ipAdEntReasmMaxSize ipNetToMediaIfIndex ipNetToMediaPhysAddress ipNetToMediaNetAddress ipNetToMediaType Note Some objects marked Not Supported do return a value, but the value is always zero. Enterprise MIBs Note For this release, Colubris-named Enterprise MIBs are still used. They apply to the HP MSM products.
Introduction Enterprise MIBs MIB MSM Controllers COLUBRIS-DEVICE-WDS-MIB ✓ COLUBRIS-DEVICE-WIRELESS-MIB ✓ ✓ COLUBRIS-IEEE802DOT11 COLUBRIS-LICENSE-MIB MSM APs ✓ ✓ (MSM325, MSM335) COLUBRIS-MAINTENANCE-MIB ✓ COLUBRIS-PUBLIC-ACCESS-MIB ✓ COLUBRIS-PUBLIC-ACCESS-RETENTION-MIB ✓ ✓ ✓ COLUBRIS-QOS-MIB COLUBRIS-SATELLITE-MANAGEMENT-MIB ✓ COLUBRIS-CONTROLLER-MIB ✓ ✓ COLUBRIS-SENSOR-MIB (MSM325, MSM335) COLUBRIS-SYSLOG-MIB ✓ ✓ COLUBRIS-SYSTEM-MIB ✓ ✓ COLUBRIS-TOOLS-MIB ✓ ✓ COLUBRIS-U
Chapter 2: MIB examples 2 MIB examples Contents Overview .......................................................................................................................2-2 Setting up Net-snmp.....................................................................................................2-2 Installing the MIBs .......................................................................................................2-3 SNMP examples...................................................................
MIB examples Overview Overview This chapter describes how to set up and use the Enterprise MIBs and to validate that they function correctly. The examples in this chapter use the Net-snmp MIB command-line browser tool for Windows. Setting up Net-snmp 1. Download the Net-snmp tools from: http://prdownloads.sourceforge.net/net-snmp/ucd-snmp-4.2.3-win32.zip?download 2. Extract the contents of the zip file to a folder named c:\net-snmp. This results in the following directory structure: 3.
MIB examples Installing the MIBs 6. Specify the following and then select OK. Variable Name: MIBDIRS Variable Value: c:\net-snmp\usr\mibs 7. In the System variables box, select Path and then select Edit. 8. Append the following to the end of the existing path and select OK. ;c:\net-snmp\usr\bin; 9. Select OK. Installing the MIBs The MIBs that you use must match the software version that is installed on your hardware. Using older MIBs may result in some SNMP MIB objects not being found.
MIB examples SNMP examples Commands Look in the c:\net-snmp\bin folder for the various executables that you can use. The examples in this section use the following commands: Note snmpwalk: Walks through the MIB tree from a specified OID (along the branch). snmpget: Gets the value requested for a specified OID object snmpset: Sets a value to a specified OID object (must be a Read-Write OID).
MIB examples SNMP examples Using snmpwalk 1. The snmpwalk command allows you to list all of the OID objects that are possible: snmpwalk -v 2c -c public -m all -Os 192.168.1.1 iso You can optionally collect the results into a file for easier review. You can save this file and use it as a guide of the Colubris OID objects. snmpwalk -v 2c -c public -m all -Os 192.168.1.1 iso > snmp.
MIB examples SNMP examples Using snmpset You can also set notifications or assign values to certain R/W OIDs. 1. This command enables a Login notification when a user logs in: snmpset -v 2c -c private -m all -Os 192.168.1.1 adminAccessLoginNotificationEnabled.0 i: enable 2. This is the same command as #1, but uses the value "1" to represent enable: snmpset -v 2c -c private -m all -Os 192.168.1.1 adminAccessLoginNotificationEnabled.0 i: 1 3.
Chapter 3: MIB descriptions 3 MIB descriptions Contents Introduction ..................................................................................................................3-3 COLUBRIS-DEVICE-EVENT-MIB ..............................................................................3-3 COLUBRIS-DEVICE-DOT1X-MIB ..............................................................................3-6 COLUBRIS-DEVICE-WIRELESS-MIB........................................................................
MIB descriptions COLUBRIS-SATELLITE-MANAGEMENT-MIB .......................................................3-71 COLUBRIS-PUBLIC-ACCESS-RETENTION-MIB...................................................3-74 COLUBRIS-MAINTENANCE-MIB ............................................................................3-76 COLUBRIS-BANDWIDTH-CONTROL-MIB .............................................................3-80 COLUBRIS-USER-SESSION-MIB .............................................................................
MIB descriptions Introduction Introduction Note For this release, Colubris-named Enterprise MIBs are still used. They apply to the HP MSM products. Colubris enterprise MIBs are used to report important status and statistics information specific to Colubris products. Several traps are also defined to reports major events. The following sections describe the functionality of the Enterprise MIB.
MIB descriptions COLUBRIS-DEVICE-EVENT-MIB coDevEvSuccessfulDisAssociationNotificationEnabled .1.3.6.1.4.1.8744.5.26.1.1.7 read-write Specifies if coDeviceEventSuccessfulDisAssociation notifications are generated. coDevEvDisAssociationFailureNotificationEnabled .1.3.6.1.4.1.8744.5.26.1.1.8 read-write Specifies if coDeviceEventDisAssociationFailure notifications are generated. coDevEvSuccessfulDeAuthenticationNotificationEnabled .1.3.6.1.4.1.8744.5.26.1.1.
MIB descriptions COLUBRIS-DEVICE-EVENT-MIB coDevEvDetMacAddress .1.3.6.1.4.1.8744.5.26.1.2.2.1.2 read-only MAC address of the device generating the events. coDevEvTime .1.3.6.1.4.1.8744.5.26.1.2.2.1.3 read-only Date and time of the event. coDevEvSSID .1.3.6.1.4.1.8744.5.26.1.2.2.1.4 read-only The SSID used by the wireless device. coDevEvRadioIndex .1.3.6.1.4.1.8744.5.26.1.2.2.1.5 read-only Radio index where the wireless device is connected. coDevEvDuplicateCount .1.3.6.1.4.1.8744.5.
MIB descriptions COLUBRIS-DEVICE-DOT1X-MIB coDeviceEventSuccessfulReAssociation .1.3.6.1.4.1.8744.5.26.2.0.3 Sent when a client station is successfully reassociated with the AP. Parameters: coDevEvMacAddress,coDevEvSSID,coDevEvStatus,coDevEvOptionalData. coDeviceEventReAssociationFailure .1.3.6.1.4.1.8744.5.26.2.0.4 Sent when a client station has failed to reassociate with the AP. Parameters: coDevEvMacAddress,coDevEvSSID,coDevEvStatus,coDevEvOptionalData. coDeviceEventSuccessfulAuthentication .1.3.6.
MIB descriptions COLUBRIS-DEVICE-DOT1X-MIB COLUBRIS-DEVICE-DOT1X-MIB OIDs coDeviceDot1xStatusTable .1.3.6.1.4.1.8744.5.32.1.2.1 not-accessible Device IEEE 802.1x wireless station status attributes. coDeviceDot1xStatusEntry .1.3.6.1.4.1.8744.5.32.1.2.1.1 not-accessible An entry in the coDeviceDot1xStatusTable. coDevDisIndex - Uniquely identifies a device on the controller. coDev1xStaIndex - Uniquely identifies a 802.1X station on the device. coDev1xStaIndex .1.3.6.1.4.1.8744.5.32.1.2.1.1.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDev1xStaEapolRxFrame .1.3.6.1.4.1.8744.5.32.1.3.1.1.1 read-only The number of valid EAPOL frames of any type that have been received by this Authenticator. coDev1xStaEapolTxFrame .1.3.6.1.4.1.8744.5.32.1.3.1.1.2 read-only The number of EAPOL frames of any type that have been transmitted by this Authenticator. coDev1xStaBackendResponses .1.3.6.1.4.1.8744.5.32.1.3.1.1.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDevWirSNRLevelNotificationInterval .1.3.6.1.4.1.8744.5.25.1.1.2 read-write Specifies the interval in minutes between SNR level notifications. coDevWirMinimumSNRLevel .1.3.6.1.4.1.8744.5.25.1.1.3 read-write A SNR level notification is generated each time the average SNR for all wireless stations connected to a VSC drops below this value. coDevWirAssociationNotificationEnabled .1.3.6.1.4.1.8744.5.25.1.1.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDevWirIfStaRadioOperState .1.3.6.1.4.1.8744.5.25.1.2.1.1.8 read-only When True indicates that the radio is enabled. coDevWirIfStaNumberOfClient .1.3.6.1.4.1.8744.5.25.1.2.1.1.9 read-only Identifies the number of associated wireless clients. coDevWirIfStaAutoChannelEnabled .1.3.6.1.4.1.8744.5.25.1.2.1.1.10 read-only When True indicates that the Auto Channel option is enabled. coDevWirIfStaAutoChannelInterval .1.3.6.1.4.1.8744.5.25.1.2.1.1.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDevWirIfStaRadioIndex - Uniquely identifies a radio on the device. coDevWirIfStsTransmittedFragmentCount .1.3.6.1.4.1.8744.5.25.1.3.1.1.1 read-only This counter is incremented for each acknowledged MPDU with an individual address in the address 1 field or an MPDU with a multicast address in the address 1 field of type Data or Management. coDevWirIfStsMulticastTransmittedFrameCount .1.3.6.1.4.1.8744.5.25.1.3.1.1.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDevWirIfStsMulticastReceivedFrameCount .1.3.6.1.4.1.8744.5.25.1.3.1.1.11 read-only This counter is incremented when an MSDU is received with the multicast bit set in the destination MAC address. coDevWirIfStsFCSErrorCount .1.3.6.1.4.1.8744.5.25.1.3.1.1.12 read-only This counter is incremented when an FCS error is detected in a received MPDU. coDevWirIfStsTransmittedFrameCount .1.3.6.1.4.1.8744.5.25.1.3.1.1.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDevWirVscStaCurrentNumberOfUsers .1.3.6.1.4.1.8744.5.25.1.5.1.1.6 read-only Indicates the number of wireless client stations connected via this VSC. coDevWirVscStaAverageSNR .1.3.6.1.4.1.8744.5.25.1.5.1.1.7 read-only Average SNR level for the users connected to this VSC. coDevWirVscStaResetStats .1.3.6.1.4.1.8744.5.25.1.5.1.1.8 read-write Reset the VSC statistics. Reading this object will always return ’idle’. coDeviceWirelessVscStatsTable .1.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDevWirVscStsTKIPCounterMeasure .1.3.6.1.4.1.8744.5.25.1.6.1.1.7 read-only Number of times the counter measure has been invoked. coDevWirVscStsTKIPReplay .1.3.6.1.4.1.8744.5.25.1.6.1.1.8 read-only Number of incoming packets with TKIP replays. coDevWirVscStsAESError .1.3.6.1.4.1.8744.5.25.1.6.1.1.9 read-only Number of incoming AES packets that were undecryptable. coDevWirVscStsAESReplay .1.3.6.1.4.1.8744.5.25.1.6.1.1.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDevWirCliStaNoiseLevel .1.3.6.1.4.1.8744.5.25.1.7.1.1.6 read-only Level of local background noise. coDevWirCliStaSNR .1.3.6.1.4.1.8744.5.25.1.7.1.1.7 read-only Relative strength of the signal level compared to the noise level. coDevWirCliStaVLAN .1.3.6.1.4.1.8744.5.25.1.7.1.1.8 read-only VLAN ID of the associated station. coDevWirCliStaTransmitRate .1.3.6.1.4.1.8744.5.25.1.7.1.1.9 read-only Current transmit rate of a associated station.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDevWirCliStaWME .1.3.6.1.4.1.8744.5.25.1.7.1.1.19 read-only true: The wireless station sends QOS data frames. false: The wireless station sends data frames. coDevWirCliStaPreviousAPAddress .1.3.6.1.4.1.8744.5.25.1.7.1.1.20 read-only Indicates the if the station roamed from this access point. coDevWirCliStaResetStats .1.3.6.1.4.1.8744.5.25.1.7.1.1.21 read-write Reset the wireless client statistics. Reading this object will always return ’idle’.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDevWirCliStaLegacyRates .1.3.6.1.4.1.8744.5.25.1.7.1.1.30 read-only Legacy rates negotiated during the association. coDevWirCliStaHTRates .1.3.6.1.4.1.8744.5.25.1.7.1.1.31 read-only HT rates negotiated during the association. coDevWirNbAssociatedStation .1.3.6.1.4.1.8744.5.25.1.7.2 read-only Number of stations in the wireless client table. coDeviceWirelessClientStatsTable .1.3.6.1.4.1.8744.5.25.1.8.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDevWirCliStaIndex - Uniquely identifies a wireless client using the specified radio on the device. coDevWirCliStsPktsTxRate1 .1.3.6.1.4.1.8744.5.25.1.9.1.1.1 read-only Number of frames transmitted at 1 Mbps since the station associated. coDevWirCliStsPktsTxRate2 .1.3.6.1.4.1.8744.5.25.1.9.1.1.2 read-only Number of frames transmitted at 2 Mbps since the station associated. coDevWirCliStsPktsTxRate5dot5 .1.3.6.1.4.1.8744.5.25.1.9.1.1.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDevWirCliStsPktsRxRate1 .1.3.6.1.4.1.8744.5.25.1.9.1.1.13 read-only Number of frames received at 1 Mbps since the station associated. coDevWirCliStsPktsRxRate2 .1.3.6.1.4.1.8744.5.25.1.9.1.1.14 read-only Number of frames received at 2 Mbps since the station associated. coDevWirCliStsPktsRxRate5dot5 .1.3.6.1.4.1.8744.5.25.1.9.1.1.15 read-only Number of frames received at 5.5 Mbps since the station associated. coDevWirCliStsPktsRxRate11 .1.3.6.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDeviceWirelessClientStatsHTRatesEntry .1.3.6.1.4.1.8744.5.25.1.10.1.1 not-accessible An entry in the coDeviceWirelessClientStatsHTRatesTable. coDevDisIndex - Uniquely identifies a device on the controller. coDevWirIfStaRadioIndex - Uniquely identifies a radio on the device. coDevWirCliStaIndex - Uniquely identifies an HT wireless client using the specified radio on the device. coDevWirCliStsPktsTxMCS0 .1.3.6.1.4.1.8744.5.25.1.10.1.1.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDevWirCliStsPktsTxMCS11 .1.3.6.1.4.1.8744.5.25.1.10.1.1.12 read-only Number of frames transmitted at MCS11 since the station associated. coDevWirCliStsPktsTxMCS12 .1.3.6.1.4.1.8744.5.25.1.10.1.1.13 read-only Number of frames transmitted at MCS12 since the station associated. coDevWirCliStsPktsTxMCS13 .1.3.6.1.4.1.8744.5.25.1.10.1.1.14 read-only Number of frames transmitted at MCS13 since the station associated. coDevWirCliStsPktsTxMCS14 .1.3.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDevWirCliStsPktsRxMCS8 .1.3.6.1.4.1.8744.5.25.1.10.1.1.25 read-only Number of frames received at MCS8 since the station associated. coDevWirCliStsPktsRxMCS9 .1.3.6.1.4.1.8744.5.25.1.10.1.1.26 read-only Number of frames received at MCS9 since the station associated. coDevWirCliStsPktsRxMCS10 .1.3.6.1.4.1.8744.5.25.1.10.1.1.27 read-only Number of frames received at MCS10 since the station associated. coDevWirCliStsPktsRxMCS11 .1.3.6.1.4.1.8744.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDevWirCliStsPktsTxMCS21 .1.3.6.1.4.1.8744.5.25.1.10.1.1.38 read-only Number of frames transmitted at MCS21 since the station associated. coDevWirCliStsPktsTxMCS22 .1.3.6.1.4.1.8744.5.25.1.10.1.1.39 read-only Number of frames transmitted at MCS22 since the station associated. coDevWirCliStsPktsTxMCS23 .1.3.6.1.4.1.8744.5.25.1.10.1.1.40 read-only Number of frames transmitted at MCS23 since the station associated. coDevWirCliStsPktsRxMCS16 .1.3.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDevDisIndex - Uniquely identifies a device on the MultiService Controller. coDevWirApIndex - Uniquely identifies an Access Point in the device detected AP table. coDevWirApIndex .1.3.6.1.4.1.8744.5.25.1.13.1.1.1 not-accessible The auxiliary variable used to identify instances of APs in the device detected AP table. coDevWirApBSSID .1.3.6.1.4.1.8744.5.25.1.13.1.1.2 read-only The wireless MAC address of the remote device. coDevWirApRadioIndex .1.3.
MIB descriptions COLUBRIS-DEVICE-WIRELESS-MIB coDeviceWirelessDetectedStationTable .1.3.6.1.4.1.8744.5.25.1.14.2 not-accessible Device Wireless detected station attributes. coDeviceWirelessDetectedStationEntry .1.3.6.1.4.1.8744.5.25.1.14.2.1 not-accessible An entry in the coDeviceWirelessDetectedStationTable. coDevDisIndex - Uniquely identifies a device on the controller. coDevWirSDetRadioIndex - Uniquely identifies a radio on the device.
MIB descriptions COLUBRIS-WIRELESS-CLIENT-MIB coDevWirDetStaTimeLastSeen .1.3.6.1.4.1.8744.5.25.1.14.2.1.11 read-only Elapsed time in seconds since the last probe has been received from this client. COLUBRIS-DEVICE-WIRELESS-MIB Traps coDeviceWirelessSNRLevelNotification .1.3.6.1.4.1.8744.5.25.2.0.1 The average SNR level for all the stations using this Virtual Service Community is below the threshold. Parameters: coDevWirVscStaBSSID,coDevWirVscStaMscVscIndex,coDevWirVscStaAverageS NR.
MIB descriptions COLUBRIS-WIRELESS-CLIENT-MIB colubrisWirelessClientConnectionNotificationEnabled .1.3.6.1.4.1.8744.5.20.1.1.7 read-write Specifies if colubrisWirelessClientConnectionNotification events are generated. colubrisWirelessClientConnectTime .1.3.6.1.4.1.8744.5.20.1.1.8 read-only Elapsed time in seconds since the device successfully associated with an access point. colubrisWirelessClientAuthorizedState .1.3.6.1.4.1.8744.5.20.1.1.
MIB descriptions COLUBRIS-WIRELESS-CLIENT-MIB colubrisWirelessClientPktsTxRate5dot5 .1.3.6.1.4.1.8744.5.20.1.2.7 read-only Number of frames transmitted at 5.5 Mbit/s since associating with an access point. colubrisWirelessClientPktsTxRate11 .1.3.6.1.4.1.8744.5.20.1.2.8 read-only Number of frames transmitted at 11 Mbit/s since associating with an access point. colubrisWirelessClientPktsTxRate6 .1.3.6.1.4.1.8744.5.20.1.2.
MIB descriptions COLUBRIS-WIRELESS-CLIENT-MIB colubrisWirelessClientPktsRxRate11 .1.3.6.1.4.1.8744.5.20.1.2.20 read-only Number of frames received at 11 Mbit/s since associating with an access point. colubrisWirelessClientPktsRxRate6 .1.3.6.1.4.1.8744.5.20.1.2.21 read-only Number of frames received at 6 Mbit/s since associating with an access point. colubrisWirelessClientPktsRxRate9 .1.3.6.1.4.1.8744.5.20.1.2.22 read-only Number of frames received at 9 Mbit/s since associating with an access point.
MIB descriptions COLUBRIS-WDS-MIB COLUBRIS-WDS-MIB This MIB is used to display information about the local mesh feature on an HP access point. IMPORTANT: To better reflect the types of services offered by this feature as it has evolved, it has been renamed from WDS to local mesh. However, for backward compatibility, the names of the objects in this MIB have not changed, only the descriptions have been updated to bring them in line with the product documentation.
MIB descriptions COLUBRIS-WDS-MIB coWDSGroupIndex .1.3.6.1.4.1.8744.5.33.1.3.1.1.1 not-accessible The auxiliary variable used to identify instances of local mesh profiles. coWDSGroupName .1.3.6.1.4.1.8744.5.33.1.3.1.1.2 read-only Friendly name of the local mesh profile. coWDSGroupState .1.3.6.1.4.1.8744.5.33.1.3.1.1.3 read-only Indicates if the local mesh profile is active on the radios. coWDSGroupSecurity .1.3.6.1.4.1.8744.5.33.1.3.1.1.
MIB descriptions COLUBRIS-WDS-MIB coWDSLinkRadio .1.3.6.1.4.1.8744.5.33.1.4.1.1.3 read-only Radio number where the local mesh peer was detected. coWDSLinkPeerMacAddress .1.3.6.1.4.1.8744.5.33.1.4.1.1.4 read-only MAC address of the local mesh peer. coWDSLinkMaster .1.3.6.1.4.1.8744.5.33.1.4.1.1.5 read-only Indicates if this link is a link to a master node, which provides access to the root network for the mesh. coWDSLinkAuthorized .1.3.6.1.4.1.8744.5.33.1.4.1.1.
MIB descriptions COLUBRIS-WDS-MIB coWDSLinkSignal .1.3.6.1.4.1.8744.5.33.1.4.1.1.16 read-only Strength of the wireless signal. coWDSLinkNoise .1.3.6.1.4.1.8744.5.33.1.4.1.1.17 read-only Level of local background noise. coWDSNetworkScanTable .1.3.6.1.4.1.8744.5.33.1.5.1 not-accessible Conceptual table for local mesh network scans. coWDSNetworkScanEntry .1.3.6.1.4.1.8744.5.33.1.5.1.1 not-accessible An Entry (conceptual row) in the WDS Network Scan Table.
MIB descriptions COLUBRIS-PUBLIC-ACCESS-MIB COLUBRIS-PUBLIC-ACCESS-MIB This MIB is used to manage public access settings in Colubris access controller devices. It includes status information and the list of authenticated users. COLUBRIS-PUBLIC-ACCESS-MIB OIDs publicAccessStatus .1.3.6.1.4.1.8744.5.1.1.1.1 read-only Identifies the current status of the authentication system. publicAccessStatusChangedCause .1.3.6.1.4.1.8744.5.1.1.1.2 read-only Identifies the last cause of a status change.
MIB descriptions COLUBRIS-PUBLIC-ACCESS-MIB publicAccessDeviceAccountingEnabled .1.3.6.1.4.1.8744.5.1.1.2.7 read-only Identifies if accounting information is generated by the device and sent to the AAA server. The device generate RADIUS accounting of type ON and OFF. This also covers accounting of all access-lists independently of where they are used. For accounting, the following status types are generated: START, INTERIM-UPDATE, and STOP.
MIB descriptions COLUBRIS-PUBLIC-ACCESS-MIB publicAccessUsersConfigIndex .1.3.6.1.4.1.8744.5.1.1.3.5.1.1 not-accessible Index of a user profile in the publicAccessUsersConfigTable. publicAccessUsersConfigAuthenType .1.3.6.1.4.1.8744.5.1.1.3.5.1.2 read-only Indicates the mechanism used to authenticate users. publicAccessUsersConfigAuthenMode .1.3.6.1.4.1.8744.5.1.1.3.5.1.3 read-only Specifies how the user authentication is performed.
MIB descriptions COLUBRIS-PUBLIC-ACCESS-MIB publicAccessUserEntry .1.3.6.1.4.1.8744.5.1.1.3.6.1 not-accessible Information about a particular user that has been authenticated by the authentication system. publicAccessUserIndex - Uniquely identifies a user in the table. publicAccessUserIndex .1.3.6.1.4.1.8744.5.1.1.3.6.1.1 not-accessible Index of a user in the publicAccessUserTable. publicAccessUserAuthenType .1.3.6.1.4.1.8744.5.1.1.3.6.1.
MIB descriptions COLUBRIS-PUBLIC-ACCESS-MIB publicAccessUserBytesReceived .1.3.6.1.4.1.8744.5.1.1.3.6.1.11 read-only Indicates the total number of bytes received by the user. When this counter reaches its maximum value, it wraps around and starts increasing again from zero. publicAccessUserPacketsSent .1.3.6.1.4.1.8744.5.1.1.3.6.1.12 read-only Indicates the total number of IP packets sent by the user.
MIB descriptions COLUBRIS-PUBLIC-ACCESS-MIB publicAccessUserApRadioIndex .1.3.6.1.4.1.8744.5.1.1.3.6.1.22 read-only Indicates the radio to which this user is associated. The index 0 is reserved when location aware is not enabled or not properly configured. It means that the system could not determine on which interface the user is connected. Please note that this information is not related to the standard SNMP interface table. It is a proprietary index information on the Radios in Colubris devices.
MIB descriptions COLUBRIS-PUBLIC-ACCESS-MIB publicAccessUserMaxReceiveRate .1.3.6.1.4.1.8744.5.1.1.3.6.1.31 read-only Specifies the maximum receive rate for the user. publicAccessUserBandwidthControlLevel .1.3.6.1.4.1.8744.5.1.1.3.6.1.32 read-only Specifies the user’s bandwidth control level. publicAccessUserNASPort .1.3.6.1.4.1.8744.5.1.1.3.6.1.33 read-only Specifies the NAS-Port value assigned to the user. publicAccessUsersLoggedInTrapEnabled .1.3.6.1.4.1.8744.5.1.1.3.
MIB descriptions COLUBRIS-DEVICE-WDS-MIB publicAccessUsersThresholdTrap .1.3.6.1.4.1.8744.5.1.2.0.2 This notification is sent whenever publicAccessUsersThreshold is exceeded. Parameters: publicAccessUsersCount. publicAccessUsersSessionStartTrap .1.3.6.1.4.1.8744.5.1.2.0.3 When a user successfully authenticate a trap is generated if the publicAccessUsersSessionTrapEnabled is set to True. Parameters: publicAccessUserName. publicAccessUsersSessionStopTrap .1.3.6.1.4.1.8744.5.1.2.0.
MIB descriptions COLUBRIS-DEVICE-WDS-MIB coDevWDSInfoMaxNumberOfGroup .1.3.6.1.4.1.8744.5.34.1.2.1.1.1 read-only Maximum number of local mesh profiles supported by the device. coDeviceWDSRadioTable .1.3.6.1.4.1.8744.5.34.1.3.1 not-accessible Conceptual table for the local mesh radio parameters. coDeviceWDSRadioEntry .1.3.6.1.4.1.8744.5.34.1.3.1.1 not-accessible An Entry (conceptual row) in the local mesh radio Table. coDevDisIndex - Uniquely identifies a device on the controller.
MIB descriptions COLUBRIS-DEVICE-WDS-MIB coDevWDSGroupSecurity .1.3.6.1.4.1.8744.5.34.1.4.1.1.4 read-only Specifies the encryption used by the local mesh profile. coDevWDSGroupDynamicMode .1.3.6.1.4.1.8744.5.34.1.4.1.1.5 read-only Specifies the mode of the dynamic local mesh profile. coDevWDSGroupDynamicGroupId .1.3.6.1.4.1.8744.5.34.1.4.1.1.6 read-only Specifies the mesh ID identifier of the dynamic local mesh profile. coDeviceWDSLinkStatusTable .1.3.6.1.4.1.8744.5.34.1.5.
MIB descriptions COLUBRIS-DEVICE-WDS-MIB coDevWDSLinkStaEncryption .1.3.6.1.4.1.8744.5.34.1.5.1.1.7 read-only Specifies the encryption used by the local mesh link. coDevWDSLinkStaIdleTime .1.3.6.1.4.1.8744.5.34.1.5.1.1.8 read-only Inactivity time. coDevWDSLinkStaSNR .1.3.6.1.4.1.8744.5.34.1.5.1.1.9 read-only Signal noise ratio of the local mesh peer. coDevWDSLinkStaTxRate .1.3.6.1.4.1.8744.5.34.1.5.1.1.10 read-only Current transmit rate of the local mesh peer. coDevWDSLinkStaRxRate .
MIB descriptions COLUBRIS-DEVICE-WDS-MIB coDevWDSGroupIndex - Uniquely identify a local mesh profile inside the Device local mesh profile table. coDevWDSLinkIndex - Uniquely identify a local mesh link inside a Device local mesh profile. coDevWDSLinkStsPktsTxRate1 .1.3.6.1.4.1.8744.5.34.1.5.2.1.1 read-only Number of frames transmitted at 1 Mbps. coDevWDSLinkStsPktsTxRate2 .1.3.6.1.4.1.8744.5.34.1.5.2.1.2 read-only Number of frames transmitted at 2 Mbps. coDevWDSLinkStsPktsTxRate5dot5 .1.3.6.1.
MIB descriptions COLUBRIS-DEVICE-WDS-MIB coDevWDSLinkStsPktsRxRate1 .1.3.6.1.4.1.8744.5.34.1.5.2.1.13 read-only Number of frames received at 1 Mbps. coDevWDSLinkStsPktsRxRate2 .1.3.6.1.4.1.8744.5.34.1.5.2.1.14 read-only Number of frames received at 2 Mbps. coDevWDSLinkStsPktsRxRate5dot5 .1.3.6.1.4.1.8744.5.34.1.5.2.1.15 read-only Number of frames received at 5.5 Mbps. coDevWDSLinkStsPktsRxRate11 .1.3.6.1.4.1.8744.5.34.1.5.2.1.16 read-only Number of frames received at 11 Mbps.
MIB descriptions COLUBRIS-DEVICE-WDS-MIB coDeviceWDSLinkStatsHTRatesEntry .1.3.6.1.4.1.8744.5.34.1.5.3.1 not-accessible An Entry (conceptual row) in the WDS HT Link Statistics Table. coDevDisIndex Uniquely identifies a device on the MultiService Controller. coDevWDSGroupIndex - Uniquely identify a local mesh profile inside the Device local mesh profiletable. coDevWDSLinkIndex - Uniquely identify a local mesh link inside a Device local mesh profile. coDevWDSLinkStsPktsTxMCS0 .1.3.6.1.4.1.8744.5.34.1.
MIB descriptions COLUBRIS-DEVICE-WDS-MIB coDevWDSLinkStsPktsTxMCS10 .1.3.6.1.4.1.8744.5.34.1.5.3.1.11 read-only Number of frames transmitted at MCS10 since the link was established. coDevWDSLinkStsPktsTxMCS11 .1.3.6.1.4.1.8744.5.34.1.5.3.1.12 read-only Number of frames transmitted at MCS11 since the link was established. coDevWDSLinkStsPktsTxMCS12 .1.3.6.1.4.1.8744.5.34.1.5.3.1.13 read-only Number of frames transmitted at MCS12 since the link was established. coDevWDSLinkStsPktsTxMCS13 .1.
MIB descriptions COLUBRIS-DEVICE-WDS-MIB coDevWDSLinkStsPktsRxMCS7 .1.3.6.1.4.1.8744.5.34.1.5.3.1.24 read-only Number of frames received at MCS7 since the link was established. coDevWDSLinkStsPktsRxMCS8 .1.3.6.1.4.1.8744.5.34.1.5.3.1.25 read-only Number of frames received at MCS8 since the link was established. coDevWDSLinkStsPktsRxMCS9 .1.3.6.1.4.1.8744.5.34.1.5.3.1.26 read-only Number of frames received at MCS9 since the link was established. coDevWDSLinkStsPktsRxMCS10 .1.3.6.1.4.1.8744.
MIB descriptions COLUBRIS-CDP-MIB coDevWDSScanPeerIndex .1.3.6.1.4.1.8744.5.34.1.6.1.1.2 not-accessible Uniquely identify a local mesh peer on a radio. coDevWDSScanGroupId .1.3.6.1.4.1.8744.5.34.1.6.1.1.3 read-only Group id used by the local mesh peer. coDevWDSScanPeerMacAddress .1.3.6.1.4.1.8744.5.34.1.6.1.1.4 read-only MAC address of the local mesh peer. coDevWDSScanChannel .1.3.6.1.4.1.8744.5.34.1.6.1.1.5 read-only Channel on which the peer is transmitting. coDevWDSScanSNR .1.3.6.
MIB descriptions COLUBRIS-CDP-MIB coCdpCacheDeviceIndex .1.3.6.1.4.1.8744.5.9.1.1.1.1.1 not-accessible A unique value for each device from which CDP messages are received. coCdpCacheLocalInterface .1.3.6.1.4.1.8744.5.9.1.1.1.1.2 read-only Indicates the name of the interface that received the CDP message. coCdpCacheAddress .1.3.6.1.4.1.8744.5.9.1.1.1.1.3 read-only Indicates the IP address of the device that sent the CDP message. coCdpCacheDeviceId .1.3.6.1.4.1.8744.5.9.1.1.1.1.
MIB descriptions COLUBRIS-USAGE-INFORMATION-MIB coCdpCachePortId .1.3.6.1.4.1.8744.5.9.1.1.1.1.9 read-only Indicates the Port-ID string as reported in the most recent CDP message. This will typically be the value of the ifName object (e.g., ’Ethernet0’). A zero-length string indicates no Port-ID field (TLV) was reported in the most recent CDP message. coCdpGlobalMessageInterval .1.3.6.1.4.1.8744.5.9.1.2.1 read-write Specifies the interval at which CDP messages will be generated.
MIB descriptions COLUBRIS-VSC-MIB coUsInfoCpuUse20Sec .1.3.6.1.4.1.8744.5.21.1.1.8 read-only Average CPU usage during the last 20 seconds. coUsInfoRamTotal .1.3.6.1.4.1.8744.5.21.1.1.9 read-only Total system RAM. coUsInfoRamFree .1.3.6.1.4.1.8744.5.21.1.1.10 read-only Available system RAM. coUsInfoRamBuffer .1.3.6.1.4.1.8744.5.21.1.1.11 read-only Memory used by the buffers. coUsInfoRamCached .1.3.6.1.4.1.8744.5.21.1.1.12 read-only Memory used by the system cache.
MIB descriptions COLUBRIS-QOS-MIB coVscCfgFriendlyVscName .1.3.6.1.4.1.8744.5.22.1.1.1.1.2 read-only The friendly name associated with the VSC. coVscCfgSSID .1.3.6.1.4.1.8744.5.22.1.1.1.1.3 read-only Service Set ID assigned to the VSC. coVscCfgAccessControlled .1.3.6.1.4.1.8744.5.22.1.1.1.1.4 read-only Indicates if the VSC is access-controlled. coVscCfgSecurity .1.3.6.1.4.1.8744.5.22.1.1.1.1.5 read-only Indicates the type of wireless protection used by the VSC. coVscCfgEncryption .1.
MIB descriptions COLUBRIS-QOS-MIB coQOSQueueId .1.3.6.1.4.1.8744.5.13.1.1.1.1.1 not-accessible Queue identifier used to access the statistics. coQOSTransmittedFrameCount .1.3.6.1.4.1.8744.5.13.1.1.1.1.2 read-only This counter increments only when an acknowledged MPDU with an individual address in address 1 field, or MPDU with a multicast address in the address 1 field of type Data or Management is transmitted. coQOSMulticastTransmittedFrameCount .1.3.6.1.4.1.8744.5.13.1.1.1.1.
MIB descriptions COLUBRIS-VIRTUAL-AP-MIB COLUBRIS-VIRTUAL-AP-MIB HP devices can create one or more virtual service communities (VSCs), each with their own configuration settings. Each VSC is a distinct entity, and can be customized to provide specific types of services, enabling the device to support a wide variety of users. IMPORTANT: To better reflect the types of services offered by this feature as it has evolved, it has been renamed several times.
MIB descriptions COLUBRIS-LICENSE-MIB coVirtualApAuthenMode .1.3.6.1.4.1.8744.5.11.1.1.1.1.7 read-only Identifies if user authentication is performed locally or via an external authentication server. coVirtualApAuthenProfileIndex .1.3.6.1.4.1.8744.5.11.1.1.1.1.8 read-only Specifies the authentication server profile to use for user authentication.
MIB descriptions COLUBRIS-SYSLOG-MIB COLUBRIS-LICENSE-MIB OIDs coLicenseFeatureTable .1.3.6.1.4.1.8744.5.29.1.1.1 not-accessible License information attributes. coLicenseFeatureEntry .1.3.6.1.4.1.8744.5.29.1.1.1.1 not-accessible An entry in the coLicenseFeatureTable. coLicenseFeatureIndex - Uniquely identify a license feature in a Colubris product. coLicenseFeatureIndex .1.3.6.1.4.1.8744.5.29.1.1.1.1.1 not-accessible Uniquely identify a license feature on an HP device. coLicenseFeatureName .
MIB descriptions COLUBRIS-SYSLOG-MIB syslogRegExMatchNotificationEnabled .1.3.6.1.4.1.8744.5.3.1.1.2 read-write Specifies if syslogRegExMatchNotification events are generated. syslogSeverityLevel .1.3.6.1.4.1.8744.5.3.1.1.3 read-write Specifies the severity level of messages that the syslog daemon will log. Only messages with a severity level equal to or greater than syslogSeverityLevel will be logged.
MIB descriptions HP-WLAN-NOTIFICATIONS-MIB syslogRegExMatchNotification .1.3.6.1.4.1.8744.5.3.2.0.2 Sent when the device generated a syslog message that matches the regular expression specified in syslogMessageRegEx. Parameters: syslogMsgNumber,syslogMsgFacility,syslogMsgSeverity,syslogMsgText. HP-WLAN-NOTIFICATIONS-MIB This MIB module is used for Events and Alarms generated in the wireless controller and APs and to send notifications when Events and Alarms occur.
MIB descriptions HP-WLAN-NOTIFICATIONS-MIB hpWlanNotificationsEventsDescription .1.3.6.1.4.1.11.2.14.11.6.4.4.1.1.1.1.7 read-only Description detailing the Event. hpWlanNotificationsEventsOccurrenceTime .1.3.6.1.4.1.11.2.14.11.6.4.4.1.1.1.1.8 read-only Time at which the Event occurred. hpWlanNotificationsEventsNotificationEnabled .1.3.6.1.4.1.11.2.14.11.6.4.4.1.1.2.1 read-write Indicates whether SNMP notifications are to be sent for Events generated. When enabled, notifications are sent.
MIB descriptions HP-WLAN-NOTIFICATIONS-MIB hpWlanNotificationsAlarmsSeverity .1.3.6.1.4.1.11.2.14.11.6.4.4.1.2.1.1.1 read-only Specifies the Severity of the Alarm. hpWlanNotificationsAlarmsId .1.3.6.1.4.1.11.2.14.11.6.4.4.1.2.1.1.2 not-accessible Uniquely identifies the Alarm generated in the system. hpWlanNotificationsAlarmsDevice .1.3.6.1.4.1.11.2.14.11.6.4.4.1.2.1.1.3 read-only Identifies the device which generated the Alarm. hpWlanNotificationsAlarmsCategory .1.3.6.1.4.1.11.2.14.11.6.
MIB descriptions HP-WLAN-NOTIFICATIONS-MIB hpWlanNotificationsAlarmsProbableCause .1.3.6.1.4.1.11.2.14.11.6.4.4.1.2.1.1.14 read-only Specifies the Probable Cause for a generated Alarm. hpWlanNotificationsAlarmsRecommendedAction .1.3.6.1.4.1.11.2.14.11.6.4.4.1.2.1.1.15 read-only Specifies the recommended Action to resolve the Alarm. hpWlanNotificationsAlarmsNotificationEnabled .1.3.6.1.4.1.11.2.14.11.6.4.4.1.2.2.1 read-write Indicates whether notifications are to be sent for Alarms generated.
MIB descriptions COLUBRIS-TCP-SERIAL-MIB HP-WLAN-NOTIFICATIONS-MIB Traps hpWlanNotificationsEventNotification .1.3.6.1.4.1.11.2.14.11.6.4.4.2.0.1 A generic notification is sent when an Event occurs. Includes Device, Category, Type, Description, Severity and Occurrence Time details for the generated event.
MIB descriptions COLUBRIS-DEVICE-MIB coTCPSerialRxBytes .1.3.6.1.4.1.8744.5.37.1.1.6 read-only Number of bytes received from the serial device. COLUBRIS-DEVICE-MIB This MIB is used to display information about the APs managed by a controller. COLUBRIS-DEVICE-MIB OIDs coDeviceStateChangeNotificationEnabled .1.3.6.1.4.1.8744.5.23.1.1.1 read-write Specifies if the coDeviceStateChangeNotification notification is generated. coDeviceAuthorizationFailureNotificationEnabled .1.3.6.1.4.1.8744.5.23.1.1.
MIB descriptions COLUBRIS-DEVICE-MIB coDevDisMacAddress .1.3.6.1.4.1.8744.5.23.1.2.1.1.3 read-only Ethernet MAC address of the device. coDevDisIpAddress .1.3.6.1.4.1.8744.5.23.1.2.1.1.4 read-only IP address of the device. coDevDisState .1.3.6.1.4.1.8744.5.23.1.2.1.1.5 read-only Device operational state. coDevDisSystemName .1.3.6.1.4.1.8744.5.23.1.2.1.1.6 read-only Name assigned to the device by the configuration tool. coDevDisLocation .1.3.6.1.4.1.8744.5.23.1.2.1.1.
MIB descriptions COLUBRIS-DEVICE-MIB coDevInfoProductName .1.3.6.1.4.1.8744.5.23.1.3.1.1.2 read-only Product name for the device. coDevInfoFirmwareRevision .1.3.6.1.4.1.8744.5.23.1.3.1.1.3 read-only Revision number of the device firmware. coDevInfoBootRevision .1.3.6.1.4.1.8744.5.23.1.3.1.1.4 read-only Revision number of the device boot loader. coDevInfoHardwareRevision .1.3.6.1.4.1.8744.5.23.1.3.1.1.5 read-only Revision number of the system hardware. coDeviceStatusTable .1.3.6.1.4.1.
MIB descriptions COLUBRIS-DEVICE-MIB coDevStCpuUse20Sec .1.3.6.1.4.1.8744.5.23.1.4.1.1.8 read-only Average CPU usage during the last 20 seconds. coDevStRamTotal .1.3.6.1.4.1.8744.5.23.1.4.1.1.9 read-only Total system RAM. coDevStRamFree .1.3.6.1.4.1.8744.5.23.1.4.1.1.10 read-only Available system RAM. coDevStRamBuffer .1.3.6.1.4.1.8744.5.23.1.4.1.1.11 read-only Memory used by the buffers. coDevStRamCached .1.3.6.1.4.1.8744.5.23.1.4.1.1.12 read-only Memory used by the system cache.
MIB descriptions COLUBRIS-USER-ACCOUNT-MIB coDeviceFirmwareFailureNotification .1.3.6.1.4.1.8744.5.23.2.0.4 A coDeviceFirmwareFailureNotification trap signifies that the SNMP entity has detected a device firmware failure. Parameters: coDevDisSerialNumber,coDevDisIpAddress,coDevDisState,coDevDisSystemNa me. coDeviceConfigurationFailureNotification .1.3.6.1.4.1.8744.5.23.2.0.5 A coDeviceConfigurationFailureNotification trap signifies that the SNMP entity has detected a device configuration failure.
MIB descriptions COLUBRIS-802DOT1X-ACCESS-MIB coUserAccRemainingSessionTime .1.3.6.1.4.1.8744.5.35.1.1.1.1.6 read-only Time before next logout. coUserAccStatus .1.3.6.1.4.1.8744.5.35.1.1.1.1.7 read-only Current status of the user account based on the rules defined in the associated subscription plan. coUserAccExpirationTime .1.3.6.1.4.1.8744.5.35.1.1.1.1.8 read-only This field include the date and time of the account expiration based on the subscription profile.
MIB descriptions COLUBRIS-SATELLITE-MANAGEMENT-MIB coDot1xAuthServerTimeout .1.3.6.1.4.1.8744.5.8.1.2.4 read-write Specifies the initial value of the serverTimeout constant used by the Backend Authentication state machine. coDot1xAuthMaxReq .1.3.6.1.4.1.8744.5.8.1.2.5 read-write Specifies the initial value of the maxReq constant used by the Backend Authentication state machine. coDot1xAuthReAuthPeriod .1.3.6.1.4.1.8744.5.8.1.2.
MIB descriptions COLUBRIS-SATELLITE-MANAGEMENT-MIB satelliteEntry .1.3.6.1.4.1.8744.5.7.1.1.1.1 not-accessible Information about a Satellite access point currently registered by the Master access point. satelliteIndex - Uniquely identifies a device in the satellite table. satelliteIndex .1.3.6.1.4.1.8744.5.7.1.1.1.1.1 not-accessible Index of a the satellite in the satelliteTable. satelliteDeviceId .1.3.6.1.4.1.8744.5.7.1.1.1.1.2 read-only Device ID of a the satellite in the satelliteTable.
MIB descriptions COLUBRIS-SATELLITE-MANAGEMENT-MIB satelliteSecureWebPort .1.3.6.1.4.1.8744.5.7.1.1.1.1.11 read-only Indicates the secure web port on which the satellite listens. The value zero is used when no information could be retrieved from the satellite device. satelliteDeviceMacAddress .1.3.6.1.4.1.8744.5.7.1.1.1.1.12 read-only Indicates the MAC address of the satellite access point bridge interface. satelliteProductName .1.3.6.1.4.1.8744.5.7.1.1.1.1.
MIB descriptions COLUBRIS-PUBLIC-ACCESS-RETENTION-MIB COLUBRIS-SATELLITE-MANAGEMENT-MIB Traps satelliteUpNotification .1.3.6.1.4.1.8744.5.7.2.0.1 Sent when a new satellite is detected. Parameters: satelliteName,satelliteDeviceId,satelliteMacAddress,satelliteIpAddress,satelliteS SID. satelliteDownNotification .1.3.6.1.4.1.8744.5.7.2.0.2 Sent when a satellite becomes unreachable. Parameters: satelliteName,satelliteDeviceId,satelliteMacAddress,satelliteIpAddress,satelliteS SID.
MIB descriptions COLUBRIS-PUBLIC-ACCESS-RETENTION-MIB publicAccessRetentionSessionUserName .1.3.6.1.4.1.8744.5.15.1.1.3.1.3 read-only Indicates the last username used for RADIUS authentication. publicAccessRetentionSessionStartTime .1.3.6.1.4.1.8744.5.15.1.1.3.1.4 read-only Indicates when this user session was started. publicAccessRetentionSessionDuration .1.3.6.1.4.1.8744.5.15.1.1.3.1.5 read-only Indicates how long the user’s session has been active.
MIB descriptions COLUBRIS-MAINTENANCE-MIB publicAccessRetentionPeriodTable .1.3.6.1.4.1.8744.5.15.1.2.3 not-accessible A table containing statistics on the number of authentication user’s sessions pending and terminated. publicAccessRetentionPeriodEntry .1.3.6.1.4.1.8744.5.15.1.2.3.1 not-accessible Statistics information about the number of authenticated user sessions in a given period of time. publicAccessRetentionPeriodIndex .1.3.6.1.4.1.8744.5.15.1.2.3.1.
MIB descriptions COLUBRIS-MAINTENANCE-MIB COLUBRIS-MAINTENANCE-MIB OIDs firmwarePeriodicUpdate .1.3.6.1.4.1.8744.5.2.1.1.1 read-write Specifies if firmware updates are automatically triggered on a periodic basis or not. ’true’: Automatically update the firmware based on the information specified in the firmwareUpdateDay and firmwareUpdateTime attributes. ’false’: No firmware update is triggered unless a request is specifically issued using the firmwareUpdateInitiate attribute. firmwareUpdateDay .1.3.6.
MIB descriptions COLUBRIS-MAINTENANCE-MIB ’false’: No configuration file update is triggered unless a request is specifically issued using the configurationUpdateInitiate attribute. configurationUpdateDay .1.3.6.1.4.1.8744.5.2.1.2.2 read-write When configurationPeriodicUpdate is set to true, this attribute specifies the day that automatic updates will occur. configurationUpdateTime .1.3.6.1.4.1.8744.5.2.1.2.
MIB descriptions COLUBRIS-MAINTENANCE-MIB configurationRestart .1.3.6.1.4.1.8744.5.2.1.2.11 read-write Restarts the device. Important: This will shut down all connections. Reading this object will always return ’idle’. configurationUpdateStatus .1.3.6.1.4.1.8744.5.2.1.2.12 read-only Contains the status of the current or last configuration transfer (backup or restore. A textual error message is available in configurationUpdateInfo. certificateAboutToExpireNotificationEnabled .1.3.6.1.4.1.8744.5.2.1.3.
MIB descriptions COLUBRIS-BANDWIDTH-CONTROL-MIB COLUBRIS-BANDWIDTH-CONTROL-MIB This MIB provides information on the bandwidth control settings active on an HP device. COLUBRIS-BANDWIDTH-CONTROL-MIB OIDs coBandwidthControlEnable .1.3.6.1.4.1.8744.5.14.1.1.1 read-only Indicates if bandwidth control is enabled or disabled on the Internet port. coBandwidthControlMaxTransmitRate .1.3.6.1.4.1.8744.5.14.1.1.2 read-only Indicates the maximum rate at which data can be transmitted on the Internet port.
MIB descriptions COLUBRIS-USER-SESSION-MIB coBandwidthControlLevelMinReceiveRate .1.3.6.1.4.1.8744.5.14.1.1.4.1.4 read-only Specify the minimum receive rate for the specified level as a percentage of coBandwidthControlMaxReceiveRateRate. This is the minimum amount of bandwidth that will be assigned to a level as soon as incoming traffic is present on the level. coBandwidthControlLevelMaxReceiveRate .1.3.6.1.4.1.8744.5.14.1.1.4.1.
MIB descriptions COLUBRIS-USER-SESSION-MIB coUserSessIndex .1.3.6.1.4.1.8744.5.36.1.2.1.1.1 not-accessible Index of a user in the coUserSessionTable. coUserSessUserName .1.3.6.1.4.1.8744.5.36.1.2.1.1.2 read-only Indicates the user’s name. coUserSessClientIpAddress .1.3.6.1.4.1.8744.5.36.1.2.1.1.3 read-only Indicates the user’s IP address. coUserSessSessionDuration .1.3.6.1.4.1.8744.5.36.1.2.1.1.4 read-only Indicates how long the user’s session has been active.
MIB descriptions COLUBRIS-DEVICE-IF-MIB coUserSessCallingStationID .1.3.6.1.4.1.8744.5.36.1.2.1.1.13 read-only Indicates the user’s calling station ID. coUserSessRADIUSServerProfileName .1.3.6.1.4.1.8744.5.36.1.2.1.1.14 read-only Indicates the RADIUS server profile name used to authenticate the user. coUserSessRADIUSServerIpAddress .1.3.6.1.4.1.8744.5.36.1.2.1.1.15 read-only Indicates the RADIUS server IP address used to authenticate the user. coUserSessBytesSent .1.3.6.1.4.1.8744.5.36.1.
MIB descriptions COLUBRIS-DEVICE-IF-MIB COLUBRIS-DEVICE-IF-MIB OIDs coDeviceIfStatusTable .1.3.6.1.4.1.8744.5.24.1.1.1 not-accessible Device interface status attributes. coDeviceIfStatusEntry .1.3.6.1.4.1.8744.5.24.1.1.1.1 not-accessible An entry in the coDeviceIfStatusTable. coDevDisIndex - Uniquely identifies a device on the controller. coDevIfStaIfIndex - Uniquely identifies an interface on the device. coDevIfStaIfIndex .1.3.6.1.4.1.8744.5.24.1.1.1.1.
MIB descriptions COLUBRIS-DEVICE-IF-MIB coDeviceIfStatsEntry .1.3.6.1.4.1.8744.5.24.1.2.1.1 not-accessible An entry in the coDeviceIfStatsTable. coDevDisIndex - Uniquely identify a device on the controller. coDevIfStaIfIndex - Uniquely identify an interface on the device. coDevIfStsRxBytes .1.3.6.1.4.1.8744.5.24.1.2.1.1.1 read-only The total number of octets received on the interface. coDevIfStsRxPackets .1.3.6.1.4.1.8744.5.24.1.2.1.1.
MIB descriptions COLUBRIS-SENSOR-MIB coDevIfFdbAuthorized .1.3.6.1.4.1.8744.5.24.1.3.1.1.3 read-only When True, indicates that traffic coming from this remote device is allowed. coDevIfFdbAgeing .1.3.6.1.4.1.8744.5.24.1.3.1.1.4 read-only Indicates the elapsed time when when the last frame was received for the remote device. COLUBRIS-SENSOR-MIB This MIB is used to display information about the RF sensor feature in an HP AP. COLUBRIS-SENSOR-MIB OIDs coSensorOperState .1.3.6.1.4.1.8744.5.31.1.1.
MIB descriptions COLUBRIS-CONNECTION-LIMITING-MIB coControllerNbDisController .1.3.6.1.4.1.8744.5.27.1.2.1 read-only Number of controllers in the controller discovery table. coControllerDiscoveryTable .1.3.6.1.4.1.8744.5.27.1.2.2 not-accessible Controller discovery attributes. coControllerDiscoveryEntry .1.3.6.1.4.1.8744.5.27.1.2.2.1 not-accessible An entry in the coControllerDiscoveryTable. coControllerDisIndex - Uniquely identify a Controller in the stack. coControllerDisIndex .1.3.6.1.4.1.
MIB descriptions HP-WLAN-SFLOW-EXTENSIONS-MIB COLUBRIS-CONNECTION-LIMITING-MIB OIDs connectionLimitingMaximumUserConnections .1.3.6.1.4.1.8744.5.18.1.1.1 read-write Specifies the maximum number of simultaneous connections allowed for a specific user. If this amount of connections is reached, no other connections will be allowed for user and a trap is generated. connectionLimitingNotificationEnabled .1.3.6.1.4.1.8744.5.18.1.1.
MIB descriptions COLUBRIS-CLIENT-TRACKING-MIB hpWlanSFlowRcvr80211ToEthernet .1.3.6.1.4.1.11.2.14.11.6.4.2.1.4.1.1 read-write This setting allows a receiver to support sFlow management applications that don’t implement the 802.11 extension for sFlow version 5. When set to a value other than ’unchanged,’ all of the 802.11 traffic frames that are sampled through this sFlow receiver instance will be converted to appear as Ethernet frames.
MIB descriptions COLUBRIS-CLIENT-TRACKING-MIB clientTrackingDisAssociationFailureNotificationEnabled .1.3.6.1.4.1.8744.5.19.1.1.8 read-write Specifies if clientTrackingDisAssociationFailure notifications are generated. clientTrackingSuccessfulDeAuthenticationNotificationEnabled .1.3.6.1.4.1.8744.5.19.1.1.9 read-write Specifies if clientTrackingSuccessfulDeAuthentication notifications are generated. clientTrackingDeAuthenticationFailureNotificationEnabled .1.3.6.1.4.1.8744.5.19.1.1.
MIB descriptions HP-WLAN-NEIGHBORHOOD-MIB clientTrackingSuccessfulDisAssociation .1.3.6.1.4.1.8744.5.19.2.0.7 Sent when a user is successfully disassociated from the AP. Parameters: clientTrackingEventInformation. clientTrackingDisAssociationFailure .1.3.6.1.4.1.8744.5.19.2.0.8 Sent when a user has failed to disassociate from the AP. Parameters: clientTrackingEventInformation. clientTrackingSuccessfulDeAuthentication .1.3.6.1.4.1.8744.5.19.2.0.9 Sent when a user is successfully deauthenticated.
MIB descriptions HP-WLAN-NEIGHBORHOOD-MIB hpWlanNeighborhoodRrmAnalysisDayOfWeek .1.3.6.1.4.1.11.2.14.11.6.4.3.1.1.1.6 read-write When the Radio Resource Management is run weekly, this defines the day of the week when it is run. hpWlanNeighborhoodRrmAnalysisDayOfMonth .1.3.6.1.4.1.11.2.14.11.6.4.3.1.1.1.7 read-write When the Radio Resource Management is run monthly, this defines the day of the month when it is run.
MIB descriptions HP-WLAN-NEIGHBORHOOD-MIB hpWlanNeighborhoodRrmEnabledRadiosNumber .1.3.6.1.4.1.11.2.14.11.6.4.3.1.2.1.2 read-only Indicates the number of enabled radios managed by the Radio Resource Management system. hpWlanNeighborhoodRrmConfigChangedRadiosNumber .1.3.6.1.4.1.11.2.14.11.6.4.3.1.2.1.
MIB descriptions HP-WLAN-NEIGHBORHOOD-MIB hpWlanNeighborhoodControlledApTotalRadiosNumber .1.3.6.1.4.1.11.2.14.11.6.4.3.1.2.2.1.2 read-only Indicates the total number of radios within a controlled access point. hpWlanNeighborhoodControlledApAverageDetectionTime .1.3.6.1.4.1.11.2.14.11.6.4.3.1.2.2.1.3 read-only Indicates the average time (in seconds) it takes the radios of a controlled access point to detect a rogue access point. hpWlanNeighborhoodControlledApMaximumDetectionTime .1.3.6.1.4.1.
MIB descriptions HP-WLAN-NEIGHBORHOOD-MIB hpWlanNeighborhoodNeighborTable .1.3.6.1.4.1.11.2.14.11.6.4.3.1.2.4 not-accessible Statistics for each neighbor access point (AP) detected by a discovered AP’s radio. hpWlanNeighborhoodNeighborEntry .1.3.6.1.4.1.11.2.14.11.6.4.3.1.2.4.1 not-accessible An entry in the hpWlanNeighborhoodNeighborTable. hpWlanNeighborhoodNeighborBaseBssid .1.3.6.1.4.1.11.2.14.11.6.4.3.1.2.4.1.
MIB descriptions HP-WLAN-NEIGHBORHOOD-MIB hpWlanNeighborhoodClassifiedApEntry .1.3.6.1.4.1.11.2.14.11.6.4.3.1.2.5.1 not-accessible An entry in the hpWlanNeighborhoodClassifiedApTable. hpWlanNeighborhoodClassifiedApClassification .1.3.6.1.4.1.11.2.14.11.6.4.3.1.2.5.1.1 read-write Intrusion Detection System classification for the neighbor access point. hpWlanNeighborhoodAdHocCellTable .1.3.6.1.4.1.11.2.14.11.6.4.3.1.2.
MIB descriptions HP-WLAN-NEIGHBORHOOD-MIB hpWlanNeighborhoodNetworkEntry .1.3.6.1.4.1.11.2.14.11.6.4.3.1.2.7.1 not-accessible An entry in the hpWlanNeighborhoodNetworkTable. hpWlanNeighborhoodNetworkBssid .1.3.6.1.4.1.11.2.14.11.6.4.3.1.2.7.1.1 not-accessible Basic Service Set Identifier of a wireless network as detected by an observing radio. hpWlanNeighborhoodNetworkSsid .1.3.6.1.4.1.11.2.14.11.6.4.3.1.2.7.1.
MIB descriptions COLUBRIS-802DOT11-MIB hpWlanNeighborhoodMisAssociatedStationChannel .1.3.6.1.4.1.11.2.14.11.6.4.3.1.2.8.1.5 read-only Indicates the operating channel of a mis-associated client station as detected by the Intrusion Detection System. hpWlanNeighborhoodMisAssociatedStationHtCapability .1.3.6.1.4.1.11.2.14.11.6.4.3.1.2.8.1.6 read-only Returns true if a mis-associated client station is capable of high-throughput 40Mhz channel use, as detected by the Intrusion Detection System.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11DTIMPeriod .1.3.6.1.4.1.8744.5.4.1.1.1.3 read-write Specifies the number of beacon intervals that elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period field of Beacon frames. Client stations use the DTIM to wake up from low-power mode to receive multicast traffic. coDot11PrivacyOptionImplemented .1.3.6.1.4.1.8744.5.4.1.1.1.4 read-only Indicates if the IEEE 802.
MIB descriptions COLUBRIS-802DOT11-MIB ieee802dot11g: Lowest, 6, 9, 12, 18, 24, 36, 48, 54 Mbps 11bAndg: All rates permitted. coDot11AdminMaximumDataRate .1.3.6.1.4.1.8744.5.4.1.1.1.13 read-write Specifies the maximum transmission rate that clients stations must respect to connect with this profile. Clients stations that attempt to associate at a higher data rate will be refused. The value of this object must always be greater than the value of coDot11MinimumDataRate.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11AuthenticationAlgorithmsEnable .1.3.6.1.4.1.8744.5.4.1.2.1.3 read-only This attribute, when true at a station, enables the acceptance of the authentication algorithm described in the corresponding table entry in authentication frames received by the station that have odd authentication sequence numbers. The default value of this attribute is ’true’ for the Open System table entry and ’false’ for all other table entries. coDot11WEPDefaultKeysTable .1.3.6.1.
MIB descriptions COLUBRIS-802DOT11-MIB coVirtualWlanProfileIndex - Uniquely access a profile for this particular 802.11 interface. coDot11PrivacyInvoked .1.3.6.1.4.1.8744.5.4.1.4.1.1 read-only When this attribute is TRUE, it indicates that some level of security is invoked for transmitting frames of type Data. For IEEE 802.11-1999 clients, the security mechanism used is WEP. For RSNA-capable clients, an additional variable coDot11RSNAEnabled indicates whether RSNA is enabled.
MIB descriptions COLUBRIS-802DOT11-MIB ifIndex - Each 802.11 interface is represented by an ifEntry. Interface tables in this MIB module are indexed by ifIndex. coDot11AssociationIndex - Uniquely identify a device inside the association table. coDot11AssociationIndex .1.3.6.1.4.1.8744.5.4.1.5.1.1 not-accessible The auxiliary variable used to identify instances of the columnar objects in the Association Table. coDot11StationMACAddress .1.3.6.1.4.1.8744.5.4.1.5.1.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11PktsRate12 .1.3.6.1.4.1.8744.5.4.1.5.1.13 read-only Number of frames received at 12 Mbps. coDot11PktsRate18 .1.3.6.1.4.1.8744.5.4.1.5.1.14 read-only Number of frames received at 18 Mbps. coDot11PktsRate24 .1.3.6.1.4.1.8744.5.4.1.5.1.15 read-only Number of frames received at 24 Mbps. coDot11PktsRate36 .1.3.6.1.4.1.8744.5.4.1.5.1.16 read-only Number of frames received at 36 Mbps. coDot11PktsRate48 .1.3.6.1.4.1.8744.5.4.1.5.1.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11StationName .1.3.6.1.4.1.8744.5.4.1.5.1.26 read-only Name of the associated station. coDot11StationIPAddress .1.3.6.1.4.1.8744.5.4.1.5.1.27 read-only IP address of the associated station. coDot11StationVLAN .1.3.6.1.4.1.8744.5.4.1.5.1.28 read-only VLAN ID of the associated station. This object is always available on autonomous APs.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11PktsTxRate12 .1.3.6.1.4.1.8744.5.4.1.5.1.38 read-only Number of frames transmitted at 12 Mbps. coDot11PktsTxRate18 .1.3.6.1.4.1.8744.5.4.1.5.1.39 read-only Number of frames transmitted at 18 Mbps. coDot11PktsTxRate24 .1.3.6.1.4.1.8744.5.4.1.5.1.40 read-only Number of frames transmitted at 24 Mbps. coDot11PktsTxRate36 .1.3.6.1.4.1.8744.5.4.1.5.1.41 read-only Number of frames transmitted at 36 Mbps. coDot11PktsTxRate48 .1.3.6.1.4.1.8744.5.4.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11WDSPortMacAddress .1.3.6.1.4.1.8744.5.4.1.6.1.2 read-write MAC address of the remote device on the other side of the local mesh link. coDot11WDSPortCurrentRate .1.3.6.1.4.1.8744.5.4.1.6.1.3 read-only Current rate of the local mesh link. coDot11WDSPortSNRLevel .1.3.6.1.4.1.8744.5.4.1.6.1.4 read-only Relative strength of the signal level compared to the noise level. coDot11WDSPortTxPackets .1.3.6.1.4.1.8744.5.4.1.6.1.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11ScanIndex .1.3.6.1.4.1.8744.5.4.1.7.1.1 not-accessible The auxiliary variable used to identify instances of AP in the scan table. coDot11ScanMacAddress .1.3.6.1.4.1.8744.5.4.1.7.1.2 read-only The wireless MAC address of the remote device. coDot11ScanChannel .1.3.6.1.4.1.8744.5.4.1.7.1.3 read-only The operating frequency channel of the remote device. coDot11ScanSSID .1.3.6.1.4.1.8744.5.4.1.7.1.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11ScanEnabled .1.3.6.1.4.1.8744.5.4.1.8 read-write Specifies if periodic scan should be performed or not. Not supported on the WCB-200. ’enable’: Enables periodic scans on this device. ’disable’: Disable periodic scans on this device. coDot11ScanPeriodicity .1.3.6.1.4.1.8744.5.4.1.9 read-write Specifies the time between periodic scans. Each time a scan operation is performed, only one frequency is scanned.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11StaTransmitMCS .1.3.6.1.4.1.8744.5.4.1.15.1.1 read-only MCS used while trasnmitting the last frame to the HT station. coDot11StaReceiveMCS .1.3.6.1.4.1.8744.5.4.1.15.1.2 read-only MCS used by the last frame received from the HT station. coDot11StaChannelWidth .1.3.6.1.4.1.8744.5.4.1.15.1.3 read-only Channel width used by the wireless client. coDot11StaShortGI .1.3.6.1.4.1.8744.5.4.1.15.1.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11StaPktsTxMCS9 .1.3.6.1.4.1.8744.5.4.1.15.1.14 read-only Number of transmitted frames while using MCS9. coDot11StaPktsTxMCS10 .1.3.6.1.4.1.8744.5.4.1.15.1.15 read-only Number of transmitted frames while using MCS10. coDot11StaPktsTxMCS11 .1.3.6.1.4.1.8744.5.4.1.15.1.16 read-only Number of transmitted frames while using MCS11. coDot11StaPktsTxMCS12 .1.3.6.1.4.1.8744.5.4.1.15.1.17 read-only Number of transmitted frames while using MCS12.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11StaPktsRxMCS6 .1.3.6.1.4.1.8744.5.4.1.15.1.27 read-only Number of received frames while using MCS6. coDot11StaPktsRxMCS7 .1.3.6.1.4.1.8744.5.4.1.15.1.28 read-only Number of received frames while using MCS7. coDot11StaPktsRxMCS8 .1.3.6.1.4.1.8744.5.4.1.15.1.29 read-only Number of received frames while using MCS8. coDot11StaPktsRxMCS9 .1.3.6.1.4.1.8744.5.4.1.15.1.30 read-only Number of received frames while using MCS9.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11StaPktsTxMCS18 .1.3.6.1.4.1.8744.5.4.1.15.1.40 read-only Number of transmitted frames while using MCS18. coDot11StaPktsTxMCS19 .1.3.6.1.4.1.8744.5.4.1.15.1.41 read-only Number of transmitted frames while using MCS19. coDot11StaPktsTxMCS20 .1.3.6.1.4.1.8744.5.4.1.15.1.42 read-only Number of transmitted frames while using MCS20. coDot11StaPktsTxMCS21 .1.3.6.1.4.1.8744.5.4.1.15.1.43 read-only Number of transmitted frames while using MCS21.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11StaPktsRxMCS23 .1.3.6.1.4.1.8744.5.4.1.15.1.53 read-only Number of received frames while using MCS23. coDot11StaHTRates .1.3.6.1.4.1.8744.5.4.1.15.1.54 read-only HT rates negotiated during the association. coDot11NbDetectedStation .1.3.6.1.4.1.8744.5.4.1.16 read-only Number of stations in the detected station table. coDot11DetectedStationTable .1.3.6.1.4.1.8744.5.4.1.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11DetStaRate .1.3.6.1.4.1.8744.5.4.1.17.1.7 read-only Receive rate of the last probe request received from this client. coDot11DetStaSSID .1.3.6.1.4.1.8744.5.4.1.17.1.8 read-only SSID contained in the last probe request received from this client. coDot11DetStaTimeDiscovered .1.3.6.1.4.1.8744.5.4.1.17.1.9 read-only Elapsed time in seconds since the first probe has been received from this client. coDot11DetStaTimeLastSeen .1.3.6.1.4.1.8744.5.4.1.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11LongRetryLimit .1.3.6.1.4.1.8744.5.4.2.1.1.4 read-only Indicates the maximum number of transmission attempts of a frame, the length of which is greater than coDot11RTSThreshold, that are made before a failure condition is indicated. The default value of this attribute is 4. coDot11FragmentationThreshold .1.3.6.1.4.1.8744.5.4.2.1.1.5 read-only Indicates the current maximum size, in octets, of the MPDU that may be delivered to the PHY.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11CountersEntry .1.3.6.1.4.1.8744.5.4.2.2.1 not-accessible An entry in the coDot11CountersEntry Table. ifIndex - Each 802.11 interface is represented by an ifEntry. Interface tables in this MIB module are indexed by ifIndex. coDot11TransmittedFragmentCount .1.3.6.1.4.1.8744.5.4.2.2.1.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11ReceivedFragmentCount .1.3.6.1.4.1.8744.5.4.2.2.1.10 read-only This counter is incremented for each successfully received MPDU of type Data or Management. coDot11MulticastReceivedFrameCount .1.3.6.1.4.1.8744.5.4.2.2.1.11 read-only This counter is incremented when a MSDU is received with the multicast bit set in the destination MAC address. coDot11FCSErrorCount .1.3.6.1.4.1.8744.5.4.2.2.1.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11PHYType .1.3.6.1.4.1.8744.5.4.3.1.1.1 read-only This is an 8-bit integer value that identifies the PHY type supported by the attached PLCP and PMD. Currently defined values and their corresponding PHY types are: FHSS 2.4 GHz = 01 , DSSS 2.4 GHz = 02, IR Baseband = 03, OFDM 5 GHz = 04. coDot11CurrentRegDomain .1.3.6.1.4.1.8744.5.4.3.1.1.2 read-only The current regulatory domain this instance of the PMD is supporting.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11AutoChannelEnabled .1.3.6.1.4.1.8744.5.4.3.1.1.9 read-write When True the Auto Channel option is enabled. coDot11AutoChannelInterval .1.3.6.1.4.1.8744.5.4.3.1.1.10 read-write Time interval, in minutes, between auto rescanning of the channels. Maximum is 1440 minutes (24 hours).
MIB descriptions COLUBRIS-802DOT11-MIB coDot11CurrentRxAntenna .1.3.6.1.4.1.8744.5.4.3.2.1.3 read-only The current antenna being used to receive, if the coDot11 DiversitySupport indicates that diversity is not supported. The selected antenna shall be one of the antennae marked for receive in the coDot11AntennasListTable. coDot11PhyConfigTable .1.3.6.1.4.1.8744.5.4.3.3 not-accessible PHY configuration attributes. In tabular form to allow multiple instances on an agent. coDot11PhyConfigEntry .1.3.
MIB descriptions COLUBRIS-802DOT11-MIB carrier sense and energy detect (ED_and_CS)= 04 Or the logical sum of any of these values. coDot11CurrentCCAMode .1.3.6.1.4.1.8744.5.4.3.4.1.3 read-only The current CCA method in operation. Valid values are: energy detect only (edonly) = 01 carrier sense only (csonly) = 02 carrier sense and energy detect (edandcs)= 04 coDot11RegDomainsSupportedTable .1.3.6.1.4.1.8744.5.4.3.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11AntennasListTable .1.3.6.1.4.1.8744.5.4.3.6 not-accessible This table represents the list of antennae. An antenna can be marked to be capable of transmitting, receiving, and/or for participation in receive diversity. Each entry in this table represents a single antenna with its properties. The maximum number of antennae that can be contained in this table is 255. coDot11AntennasListEntry .1.3.6.1.4.1.8744.5.4.3.6.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11SupportedDataRatesTxIndex .1.3.6.1.4.1.8744.5.4.3.7.1.1 not-accessible Index object which identifies which data rate to access. coDot11SupportedDataRatesTxValue .1.3.6.1.4.1.8744.5.4.3.7.1.2 read-only The transmit bit rates supported by the PLCP and PMD. Data rates are increments of 500Kb/s from 1 Mbps to 63.5 Mbps subject to limitations of each individual PHY. coDot11SupportedDataRatesRxTable .1.3.6.1.4.1.8744.5.4.3.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11FrequencyBandsSupported .1.3.6.1.4.1.8744.5.4.3.9.1.3 read-only The capability of the OFDM PHY implementation to operate in the three U-NII bands. Coded as an integer value of a three 1 bit fields as follow: bit 0 - Capable of operating in the lower (5.15-5.25 GHz) U-NII band. bit 1 - Capable of operating in the middle (5.25-5.35 GHz) U-NII band. bit 2 - Capable of operating in the middle (5.725-5.825 GHz) U-NII band.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11CurrentSecondaryChannel .1.3.6.1.4.1.8744.5.4.3.14.1.4 read-only This attribute indicates the channel number of the secondary channel. If 20/40 MHz mode is not currently in use, this attribute value is 0. coDot11GreenfieldOptionImplemented .1.3.6.1.4.1.8744.5.4.3.14.1.5 read-only This attribute, when TRUE, indicates that the HT Greenfield option is implemented. coDot11GreenfieldOptionEnabled .1.3.6.1.4.1.8744.5.4.3.14.1.
MIB descriptions COLUBRIS-802DOT11-MIB coDot11RSNAStatsSelectedPairwiseCipher .1.3.6.1.4.1.8744.5.4.4.1.3 read-only The AKM Suite the AP selected during association. The value consists of a three octet OUI followed by a one octet type as follows: OUI Value, Cipher, Type XX-XX-XX, 0, Reserved XX-XX-XX, 1, WEP-40 XX-XX-XX, 2, TKIP XX-XX-XX, 3, Reserved XX-XX-XX, 4, CCMP XX-XX-XX, 5, WEP-104 XX-XX-XX, 6-255, Reserved Vendor, any, Vendor Specific other, any, Reserved coDot11RSNAStatsTKIPICVErrors .1.3.
MIB descriptions COLUBRIS-AAA-CLIENT-MIB coDot11RSNAStatsTKIPReplays .1.3.6.1.4.1.8744.5.4.4.1.11 read-only Counts the number of TKIP replay errors detected. coDot11RSNAStats4WayHandshakeFailures .1.3.6.1.4.1.8744.5.4.4.1.12 read-only Counts the number of 4-Way Handshake failures. COLUBRIS-802DOT11-MIB Traps coDot11SNRLevelNotification .1.3.6.1.4.1.8744.5.4.5.0.1 The average SNR level for all the stations using this VSC during the last three intervals is low.
MIB descriptions COLUBRIS-AAA-CLIENT-MIB colubrisAAAProfileIndex .1.3.6.1.4.1.8744.5.5.1.1.1.1.1 not-accessible Specifies the index of the AAA server profile. colubrisAAAProfileName .1.3.6.1.4.1.8744.5.5.1.1.1.1.2 read-write Specifies the name of the AAA server profile. colubrisAAAProfilePrimaryServerIndex .1.3.6.1.4.1.8744.5.5.1.1.1.1.3 read-only Indicates the index number of the primary server profile in the table. A value of zero indicates that no AAA server is defined.
MIB descriptions COLUBRIS-SYSTEM-MIB colubrisAAAAuthenticationPort .1.3.6.1.4.1.8744.5.5.1.2.1.1.6 read-only Indicates the port number used by the AAA client to send authentication requests to the AAA server. colubrisAAAAccountingPort .1.3.6.1.4.1.8744.5.5.1.2.1.1.7 read-only Indicates the port number used by the AAA client to send accounting information to the AAA server. colubrisAAATimeout .1.3.6.1.4.1.8744.5.5.1.2.1.1.
MIB descriptions COLUBRIS-SYSTEM-MIB systemConfigurationVersion .1.3.6.1.4.1.8744.5.6.1.1.6 read-write User-defined string to identify the current device configuration. This string could be anything in printable ASCII characters. systemUpTime .1.3.6.1.4.1.8744.5.6.1.1.7 read-only How long the system has been running since its last restart. When this counter reaches its maximum value, it wraps around and starts increasing again from zero. systemMacAddress .1.3.6.1.4.1.8744.5.6.1.1.
MIB descriptions COLUBRIS-SYSTEM-MIB ’tp’: Look for time servers in the systemTimeServerTable in order to synchronize the device system time using the Time Protocol. systemTimeLostWhenRebooting .1.3.6.1.4.1.8744.5.6.1.2.2 read-only Indicates if the system time is lost after rebooting or not. ’true’: Indicates that the system time has been lost. ’false’: Indicates that the system time has been kept. systemTimeDSTOn .1.3.6.1.4.1.8744.5.6.1.2.
MIB descriptions COLUBRIS-SYSTEM-MIB systemTimeServerAddress .1.3.6.1.4.1.8744.5.6.1.2.7.1.2 read-write Specifies the DNS name or IP address of the time server to use. Setting an entry to a null string will delete the entry. systemTimeServerNotificationEnabled .1.3.6.1.4.1.8744.5.6.1.2.8 read-write Specifies if timeServerFailure notifications are generated. adminAccessAuthenMode .1.3.6.1.4.1.8744.5.6.1.3.
MIB descriptions COLUBRIS-SYSTEM-MIB adminAccessProfileTable .1.3.6.1.4.1.8744.5.6.1.3.8 not-accessible This table handles the profile of several administrator users. In tabular form in order to allow multiple instances on an agent. adminAccessProfileEntry .1.3.6.1.4.1.8744.5.6.1.3.8.1 not-accessible An administrator profile configured in the administrator access table. adminAccessProfileIndex .1.3.6.1.4.1.8744.5.6.1.3.8.1.1 not-accessible Specifies the index of the administrator profile.
MIB descriptions COLUBRIS-TOOLS-MIB systemHeartbeatNotification .1.3.6.1.4.1.8744.5.6.2.0.4 Sent every heartbeatPeriod. Parameters: systemSerialNumber,systemMacAddress,systemWanPortIpAddress,systemUpTi me,ifOutUcastPkts,ifInUcastPkts,ifOutErrors,ifInErrors,ifOutUcastPkts,ifInUcastPkts,ifOutErr ors,ifInErrors,ifOutUcastPkts,ifInUcastPkts,ifOutErrors,ifInErrors. adminAccessLogoutNotification .1.3.6.1.4.1.8744.5.6.2.0.5 Sent after an administrator has logout. Parameters: adminAccessInfo.
MIB descriptions COLUBRIS-TOOLS-MIB traceNumberOfPackets .1.3.6.1.4.1.8744.5.12.1.1.5 read-write Specifies the maximum number of packets (IP datagrams) the trace should capture. Once this limit is reached, the trace automatically stops. tracePacketSize .1.3.6.1.4.1.8744.5.12.1.1.6 read-write Specifies the maximum number of bytes to capture for each packet. The remaining data is discarded. traceCaptureFilter .1.3.6.1.4.1.8744.5.12.1.1.7 read-write Specifies the packet filter to use to capture data.
ProCurve 5400zl Switches Installation and Getting Startd Guide Technology for better business outcomes To learn more, visit www.hp.com/networking/ © Copyright 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
