Maintenance & Service Guide HP Pro 3005 Business PCs HP Pro 3015 Business PCs HP Pro 3085 Business PCs
© Copyright 2009 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft and Windows are trademarks of Microsoft Corporation in the U.S. and other countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
About This Book WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. NOTE: Text set off in this manner provides important supplemental information.
iv About This Book
Table of contents 1 Product Features ............................................................................................................................................ 1 Standard Configuration Features ......................................................................................................... 1 Serviceability Features ......................................................................................................................... 3 Front Panel Components ....................
4 Serial ATA (SATA) Drive Guidelines and Features .................................................................................... 22 SATA Hard Drives .............................................................................................................................. 22 SATA Hard Drive Cables .................................................................................................................... 22 SATA Data Cable ....................................................................
Drives ................................................................................................................................................. 49 Drive Positions ................................................................................................................... 49 Installing Additional Drives ................................................................................................. 50 System Board Drive Connections ............................................................
Appendix B Power Cord Set Requirements .................................................................................................. 86 General Requirements ....................................................................................................................... 86 Japanese Power Cord Requirements ................................................................................................ 86 Country-Specific Requirements ................................................................
1 Product Features Standard Configuration Features HP Pro Business PC features may vary depending on the model. For a complete listing of the hardware and software installed in the computer, run the diagnostic utility (included on some computer models only). Instructions for using the utility are provided in the Troubleshooting Guide.
Figure 1-2 HP Pro 3015 Figure 1-3 HP Pro 3085 NOTE: The drive configuration shown above may be different than your computer model. The illustration shown above may look different than your computer model.
Serviceability Features The Microtower computer includes features that make it easy to upgrade and service. A Torx T-15 or flat blade screwdriver is needed for many of the installation procedures described in this guide. Front Panel Components Drive configuration may vary by model. Figure 1-4 Front Panel Components Table 1-1 Front Panel Components 1 5.25-inch Optical Drive1 6 Hard Drive Activity Light 2 5.25-inch Optical Drive Bay 7 Optical Drive Eject Button 3 3.
Media Card Reader Components The media card reader is an optional device available on some models only. Refer to the following illustration and table to identify the media card reader components. Figure 1-5 Media Card Reader Components Table 1-2 Media Card Reader Components No.
Rear Panel Components HP Pro 3005/3085 Figure 1-6 Rear Panel Components – HP Pro 3005/3085 Table 1-3 Rear Panel Components – HP Pro 3005/3085 1 Power Cord Connector 7 Line-Out Connector for powered audio devices (green) 2 Line-In Audio Connector (blue) 8 Microphone Connector (pink) 3 RJ-45 Network Connector 9 DVI Connector 4 Universal Serial Bus (USB) Ports 10 Serial connector 5 VGA Monitor Connector 11 Keyboard PS/2 connector 6 Mouse PS/2 connector NOTE: Arrangement and number of con
HP Pro 3015 Figure 1-7 Rear Panel Components – HP Pro 3015 Table 1-4 Rear Panel Components – HP Pro 3015 1 Power Cord Connector 8 Line-Out Connector for powered audio devices (green) 2 Line-In Audio Connector (blue) 9 Microphone Connector (pink) 3 Rear Center Channel/Subwoofer Audio Connector (orange) 10 Surround Side Channel Audio Connector (gray) 4 RJ-45 Network Connector 11 Surround Rear Channel Audio Connector (black) 5 1394 connector 12 Universal Serial Bus (USB) Ports 6 VGA Monit
2 Installing and Customizing the Software If your computer was not shipped with a Microsoft operating system, some portions of this documentation do not apply. Additional information is available in online help after you install the operating system. NOTE: If the computer was shipped with Windows Vista or Windows 7 loaded, you will be prompted to register the computer with HP Total Care before installing the operating system. You will see a brief movie followed by an online registration form.
4. Click on the Windows Update link. In Windows Vista and Windows 7, the Windows Update screen appears. Click view available updates and make sure all critical updates are selected. Click the Install button and follow the instructions on the screen. In Windows XP, you will be directed to the Microsoft Windows Update Web site. If you see one or more pop-up windows that ask you to install a program from http://www.microsoft.com, click Yes to install the program.
3 Computer Setup (F10) Utility The computer setup utility differs for the HP Pro 3005/3085 and the HP Pro 3015. HP Pro 3005/3085 – Computer Setup (F10) Utility Use Computer Setup (F10) Utility to do the following: ● Change factory default settings. ● Set the system date and time. ● Set, view, change, or verify the system configuration, including settings for processor, graphics, memory, audio, storage, communications, and input devices.
Computer Setup (F10) Utility Using Computer Setup (F10) Utilities Computer Setup can be accessed only by turning the computer on or restarting the system. To access the Computer Setup Utilities menu, complete the following steps: 1. Turn on or restart the computer. 2. As soon as the computer is turned on, press F10 before the system boots to the operating system to enter Computer Setup. Press Enter to bypass the title screen, if necessary.
Computer Setup—Main NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration.
Table 3-2 Computer Setup—Main (continued) Option Description PATA Master For each, if PATA HDD is used, allows you to: PATA Slave ● ◦ SMART Status Check ◦ SMART Short Self-Test ◦ SMART Extended Self-Test ● auto-detect HDD size and head ● set PATA Master/Slave device details on selected channel to: ● ● 12 run SMART self-test for selected channel: ◦ None ◦ Auto ◦ Manual set access mode on selected channel to: ◦ CHS (Cylinder-Head-Sector) ◦ LBA (Logical Block Addressing) ◦ Large
Table 3-2 Computer Setup—Main (continued) Option Description Halt On Allows you to set POST error behavior to: POST Delay ● No Errors ● All Errors ● All But Keyboard Allows you to set a POST delay to: ● 0 seconds ● 5 seconds ● 10 seconds ● 15 seconds ● 30 seconds Computer Setup—Advanced NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration.
Table 3-3 Computer Setup—Advanced (continued) Option Description Onboard LAN Boot ROM Disables/enables the boot ROM of the onboard LAN chip. Onboard Serial Port 1 Allows you to select a setting for the onboard serial port: ● Disabled ● 3F8/IRQ4 ● 2F8/IRQ3 ● 3E8/IRQ4 ● 2E8/IRQ3 Computer Setup—Boot NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 3-4 Computer Setup—Boot Option Description F9 Boot Menu Disables/enables F9 Boot Menu.
Table 3-4 Computer Setup—Boot (continued) Option Description Set Supervisor Password Allows you to establish a password to control access to Computer Setup. BIOS Write Protection Disables/enables BIOS upgrading. Computer Setup—Power NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration.
Table 3-6 Computer Setup—PC Health (continued) Option Description Current CPU Fan Speed (view only) Current System Fan Speed (view only) Computer Setup—Exit Table 3-7 Computer Setup—Exit Option Description Save Changes and Exit Allows you to save current settings and exit Computer Setup. Discard Changes and Exit Allows you to exit Computer Setup without saving changes. Load Optimal Defaults Allows you to reset Computer Setup to factory defaults.
Using Computer Setup (F10) Utilities Computer Setup can be accessed only by turning the computer on or restarting the system. To access the Computer Setup Utilities menu, complete the following steps: 1. Turn on or restart the computer. 2. As soon as the computer is turned on, press F10 before the system boots to the operating system to enter Computer Setup. Press Enter to bypass the title screen, if necessary.
Computer Setup—Main NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 3-9 Computer Setup—Main Option Description System Time Allows you to set system time. System Date Allows you to set system date. Language Allows you to select language. Floppy Diskette A: Allows you to set drive A to: ● Disabled ● 1.44 MB 3.
Computer Setup—Advanced NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. WARNING! Setting items on this menu to incorrect values may cause your system to malfunction.
Table 3-10 Computer Setup—Advanced (continued) USB Ports Allows you to enable/disable individual USB ports (USB Port 1 through USB Port 12). Change Supervisor Password Allows you to change the supervisor password. Computer Setup—Power NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration.
Table 3-12 Computer Setup—Boot (continued) (Boot Device Priority) Allows you to specify which device groups will boot first, second, third, and fourth or to disable any of the four: 1st Boot Device ● CD-ROM Group ● Hard Drive Group ● Floppy Group ● Network Boot Group 2nd Boot Device 3rd Boot Device 4th Boot Device NOTE: MS-DOS drive lettering assignments may not apply after a non-MS-DOS operating system has started.
4 Serial ATA (SATA) Drive Guidelines and Features NOTE: HP only supports the use of SATA hard drives on these models of computer. No Parallel ATA (PATA) drives are supported. SATA Hard Drives Serial ATA Hard Drive Characteristics Number of pins/conductors in data cable 7/7 Number of pins in power cable 15 Maximum data cable length 39.37 in (100 cm) Data interface voltage differential 400-700 mV Drive voltages 3.3 V, 5 V, 12 V Jumpers for configuring drive N/A Data transfer rate 3.
SMART ATA Drives The Self Monitoring Analysis and Recording Technology (SMART) ATA drives for the HP Personal Computers have built-in drive failure prediction that warns the user or network administrator of an impending failure or crash of the hard drive. The SMART drive tracks fault prediction and failure indication parameters such as reallocated sector count, spin retry count, and calibration retry count. If the drive determines that a failure is imminent, it generates a fault alert.
5 Identifying the Chassis, Routine Care, and Disassembly Preparation This chapter provides general service information for the computer. Adherence to the procedures and precautions described in this chapter is essential for proper service. CAUTION: When the computer is plugged into an AC power source, voltage is always applied to the system board. You must disconnect the power cord from the power source before opening the computer to prevent system board or component damage.
Removing DIPs* from vinyl tray 2,000 V 4,000 V 11,500 V Removing DIPs* from Styrofoam 3,500 V 5,000 V 14,500 V Removing bubble pack from PCB 7,000 V 20,000 V 26,500 V Packing PCBs in foam-lined box 5,000 V 11,000 V 21,000 V *These are then multi-packaged inside plastic tubes, trays, or Styrofoam. NOTE: 700 volts can degrade a product. Preventing Electrostatic Damage to Equipment Many electronic components are sensitive to ESD.
Grounding the Work Area To prevent static damage at the work area, use the following precautions: ● Cover the work surface with approved static-dissipative material. Provide a wrist strap connected to the work surface and properly grounded tools and equipment. ● Use static-dissipative mats, foot straps, or air ionizers to give added protection. ● Handle electrostatic sensitive components, parts, and assemblies by the case or PCB laminate. Handle them only at static-free work areas.
Operating Guidelines To prevent overheating and to help prolong the life of the computer: ● Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold. ● Operate the computer on a sturdy, level surface. Leave a 10.2-cm (4-inch) clearance on all vented sides of the computer and above the monitor to permit the required airflow. ● Never restrict the airflow into the computer by blocking any vents or air intakes.
Routine Care General Cleaning Safety Precautions 1. Never use solvents or flammable solutions to clean the computer. 2. Never immerse any parts in water or cleaning solutions; apply any liquids to a clean cloth and then use the cloth on the component. 3. Always unplug the computer when cleaning with liquids or damp cloths. 4. Always unplug the computer before cleaning the keyboard, mouse, or air vents. 5. Disconnect the keyboard before cleaning it. 6.
● If you remove a key, use a specially designed key puller to prevent damage to the keys. This tool is available through many electronic supply outlets. CAUTION: Never remove a wide leveled key (like the space bar) from the keyboard. If these keys are improperly removed or installed, the keyboard may not function properly. ● Cleaning under a key may be done with a swab moistened with isopropyl alcohol and squeezed out. Be careful not to wipe away lubricants necessary for proper key functions.
● Diagnostics software ● HP tamper-resistant T-15 wrench (Smart Cover FailSafe Key, PN 166527-001) or HP tamperresistant bits (Smart Cover FailSafe Key, PN 166527-002) Screws The screws used in the computer are not interchangeable. They may have standard or metric threads and may be of different lengths. If an incorrect screw is used during the reassembly process, it can damage the unit.
Lithium Coin Cell Battery The battery that comes with the computer provides power to the real-time clock and has a minimum lifetime of about three years. See the appropriate removal and replacement chapter for the chassis you are working on in this guide for instructions on the replacement procedures. WARNING! This computer contains a lithium battery. There is a risk of fire and chemical burn if the battery is handled improperly.
6 Removal and Replacement Procedures Microtower (MT) Chassis Adherence to the procedures and precautions described in this chapter is essential for proper service. After completing all necessary removal and replacement procedures, run the Diagnostics utility to verify that all components operate properly. NOTE: Not all features listed in this guide are available on all computers. Preparation for Disassembly 1. Close any open software applications. 2. Exit the operating system. 3.
Access Panel 1. Prepare the computer for disassembly (Preparation for Disassembly on page 32). 2. Loosen the screw (1) that secures the access panel to the computer chassis. 3. Slide the access panel back (2) about 1.3 cm (1/2 inch), then lift it off the unit. NOTE: You may want to lay the computer on its side to install internal parts. Be sure the side with the access panel is facing up. Figure 6-1 Removing the Computer Access Panel To replace the access panel, reverse the removal steps.
Front Bezel 1. Prepare the computer for disassembly (Preparation for Disassembly on page 32). 2. Remove the access panel (Access Panel on page 33). 3. Press outward on the three latches on the right side of the bezel (1), then rotate the right side of the bezel off the chassis (2) followed by the left side. Figure 6-2 Removing the Front Bezel NOTE: The appearance of the front bezel may vary. To reinstall the front bezel, reverse the removal procedure.
Bezel Blanks On some models, there are bezel blanks covering the 3.5-inch and 5.25-inch external drive bays that need to be removed before installing a drive. To remove a bezel blank: 1. Remove the front bezel (Front Bezel on page 34). 2. To remove the lower 5.25-inch bezel blank, gently twist and pull on the bezel blank until it breaks free from the front bezel (1), then discard the bezel blank. If the blank needs to be replaced at a later date, you can order a replacement blank from HP. 3.
Memory The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3SDRAM) dual inline memory modules (DIMMs). DDR3-SDRAM DIMMs The memory sockets on the system board can be populated with up to four industry-standard DIMMs. These memory sockets are populated with at least one preinstalled DIMM. To achieve the maximum memory support, you can populate the system board with up to 8 GB of memory configured in a highperforming dual channel mode.
Populating DIMM Sockets There are four DIMM sockets on the system board, with two sockets per channel.
Figure 6-5 DIMM Socket Locations – HP Pro 3015 Table 6-1 DIMM Socket Locations Item Description Socket Color (HP Pro 3005/3085) Socket Color (HP Pro 3015) Insertion Order 1 XMM1 socket, Channel A (populate first) White Blue 1 2 XMM2 socket, Channel A White Blue 2 3 XMM3 socket, Channel B Black Black 3 4 XMM4 socket, Channel B Black Black 4 NOTE: A DIMM must occupy the XMM1 socket.
dual channel and the remainder is assigned to single channel. For optimal speed, the channels should be balanced so that the largest amount of memory is spread between the two channels. If one channel will have more memory than the other, the larger amount should be assigned to Channel A. For example, if you are populating the sockets with one 2-GB DIMM, and three 1-GB DIMMs, Channel A should be populated with the 2-GB DIMM and one 1-GB DIMM, and Channel B should be populated with the two 1-GB DIMMs.
4. Open both latches of the memory module socket (1), and insert the memory module into the socket (2). Figure 6-6 Installing a DIMM NOTE: A memory module can be installed in only one way. Match the notch on the module with the tab on the memory socket. A DIMM must occupy the DIMM1 socket. Always populate the blue sockets before the black sockets in each channel. To create a dual-channel memory configuration, the memory capacity of Channel A must equal the memory capacity of Channel B.
Expansion Cards The HP Pro 3005/3085 has two PCI expansion slots, one PCI Express x1 expansion slot, and one PCI Express x16 expansion slot. The expansion slots accommodate full-height or half-height expansion cards.
Figure 6-8 Expansion Slot Locations – HP Pro 3015 Table 6-3 Expansion Slot Locations – HP Pro 3015 Item Description 1 PCI expansion slot 2 PCI Express x1 expansion slot 3 PCI Express x1 expansion slot 4 PCI Express x16 expansion slot NOTE: You can install a PCI Express x1, x4, x8, or x16 expansion card in the PCI Express x16 expansion slot. To remove, replace, or add an expansion card: 42 1. Prepare the computer for disassembly (Preparation for Disassembly on page 32). 2.
4. On the rear of the computer, a slot cover lock secures the expansion card brackets in place. Remove the screw from the slot cover lock then slide the slot cover lock up to remove it from the chassis. Figure 6-9 Opening the Slot Cover Lock 5. Before installing an expansion card, remove the expansion slot cover or the existing expansion card. NOTE: Before removing an installed expansion card, disconnect any cables that may be attached to the expansion card. a.
b. If you are removing a standard PCI card or PCI Express x1 card, hold the card at each end, and carefully rock it back and forth until the connectors pull free from the socket. Pull the expansion card straight up from the socket then away from the inside of the chassis to release it from the chassis frame. Be sure not to scrape the card against the other components. Figure 6-11 Removing a PCI or PCI Express x1 Expansion Card c.
7. If you are not installing a new expansion card, install an expansion slot cover to close the open slot. CAUTION: After removing an expansion card, you must replace it with a new card or expansion slot cover for proper cooling of internal components during operation. 8.
10. Connect external cables to the installed card, if needed. Connect internal cables to the system board, if needed. 11. Replace the computer access panel. 12. Reconnect the power cord and any external devices, then turn on the computer. 13. Lock any security devices that were disengaged when the access panel was removed. 14. Reconfigure the computer, if necessary. Refer to the Computer Setup (F10) Utility Guide for instructions on using Computer Setup.
2. Grasp the cable end of the connector and pull it straight up (2). CAUTION: Always pull the connector - NEVER pull on the cable. Pulling on the cable could damage the cable and result in a failed power supply. Cable Connections HP Pro 3005/3085 System board connectors are color-coded to make it easier to find the proper connection.
HP Pro 3015 System board connectors are color-coded to make it easier to find the proper connection.
Drives The computer supports up to five drives that may be installed in various configurations. This section describes the procedure for replacing or upgrading the storage drives. A Torx T-15 screwdriver is needed to remove and install the guide screws on a drive. Drive Positions NOTE: Front bezel appearance may vary. Figure 6-15 Drive Positions 1 Two 5.25-inch external drive bays for optional drives (optical drives shown) 2 One 3.
Installing Additional Drives When installing additional drives, follow these guidelines: ● The primary Serial ATA (SATA) hard drive must be connected to the dark blue primary SATA connector on the system board. ● Connect the first SATA optical drive to the white SATA connector on the system board. ● Always populate the dark blue and white connectors before the light blue and orange connectors. ● The system does not support Parallel ATA (PATA) optical drives or PATA hard drives.
System Board Drive Connections Refer to the following illustration and table to identify the system board drive connectors.
Figure 6-18 System Board Drive Connections – HP Pro 3015 Table 6-4 System Board Drive Connections 52 No.
Removing an Optical Drive CAUTION: All removable media should be taken out of a drive before removing the drive from the computer. To remove an optical drive: 1. Prepare the computer for disassembly (Preparation for Disassembly on page 32). 2. Remove the access panel (Access Panel on page 33). 3. Remove the front bezel (Front Bezel on page 34). 4. Disconnect the power cable (1) and data cable (2) from the rear of the optical drive. Figure 6-19 Disconnecting the Power and Data Cables 5.
NOTE: To install an optical drive, refer to Installing an Optical Drive into the 5.25-inch Drive Bay on page 54. Installing an Optical Drive into the 5.25-inch Drive Bay To install an optional 5.25-inch optical drive: 1. Prepare the computer for disassembly (Preparation for Disassembly on page 32). 2. Remove the access panel (Access Panel on page 33). 3. Remove the front bezel (Front Bezel on page 34). 4.
9. Connect the power cable (1) and data cable (2) to the rear of the optical drive. Figure 6-22 Connecting the Power and Data Cables 10. Replace the front bezel and access panel. 11. Reconnect the power cord and turn on the computer. 12. Lock any security devices that were disengaged when the access panel was removed. The system automatically recognizes the drive and reconfigures the computer. Removing an External 3.
5. Remove the two retainer screws that secure the drive to the bay (1) then slide the drive forward and out of the bay (2). Figure 6-23 Removing a 3.5-inch Device (Media Card Reader Shown) Installing a Drive into the 3.5-inch External Drive Bay The 3.5-inch external drive bay on the front of the computer can be configured with a media card reader. 56 1. Prepare the computer for disassembly (Preparation for Disassembly on page 32). 2. Remove the access panel (Access Panel on page 33). 3.
7. Slide the drive in through the front of the chassis (1) until the bezel on the drive is evenly aligned with the computer front bezel and install the two M3 metric retainer screws (2) as shown in the illustration below. NOTE: Extra drive retainer screws are provided on the interior of the front bezel if needed. The M3 metric retainer screws for diskette drives or media card readers are black. Refer to Installing Additional Drives on page 50 for an illustration of the retainer screws location.
3. Remove the two screws that secure the hard drive cage to the chassis. Figure 6-25 Removing the Hard Drive Cage Screws 4. Push down the latch on the side of the hard drive cage (1), then slide the hard drive cage away from the bottom of the chassis (2) as shown below.
5. Lift the hard drive cage out of the chassis. Figure 6-27 Removing the Hard Drive Cage 6. Disconnect the power cable (1) and data cable (2) from the back of the hard drive.
7. Remove the four screws that secure the hard disk drive to the hard drive cage (1), then slide the hard disk drive out of the hard drive cage (2). Figure 6-29 Removing the Hard Drive NOTE: To install an internal 3.5-inch hard drive, refer to Installing an Internal 3.5-inch Hard Drive on page 61.
Installing an Internal 3.5-inch Hard Drive 1. Follow the steps in Removing an Internal 3.5-inch Hard Drive on page 57 to remove the hard drive cage and, if necessary, the existing hard drive. 2. Slide the new drive into the hard disk drive cage (1), aligning the drive with the four screw holes on the cage. Install the four 6-32 standard screws that secure the hard disk drive to the hard disk drive cage (2). Make sure the hard disk drive cables are facing the top of the drive cage.
3. Connect the power cable (1) and data cable (2) to the back of the hard drive. Figure 6-31 Connecting the Hard Drive Cables CAUTION: Never crease or bend a SATA data cable tighter than a 30 mm (1.18 in) radius. A sharp bend can break the internal wires. 4. Place the hard disk drive cage into the chassis (1), then slide it down toward the bottom of the chassis until it locks into place (2).
5. Attach the two screws that secure the hard disk drive cage to the chassis. Figure 6-33 Securing the Hard Drive Cage 6. If installing a new drive, connect the opposite end of the data cable to the appropriate system board connector. If your system has only one SATA hard drive, you must connect the hard drive data cable to the dark blue connector to avoid any hard drive performance problems.
Front I/O and USB Panel Housing Assembly 1. Prepare the computer for disassembly (Preparation for Disassembly on page 32). 2. Remove the access panel (Access Panel on page 33) 3. Lay the computer on its side with the front facing toward you. 4. Remove the front bezel (Front Bezel on page 34). 5. Unplug the four cables that connect the assembly to the system board. The assembly cables connect to the following system board connectors: 6.
Power Switch/LED Assembly 1. Prepare the computer for disassembly (Preparation for Disassembly on page 32). 2. Remove the access panel (Access Panel on page 33). 3. Lay the computer on its side with the front facing toward you. 4. Remove the front bezel (Front Bezel on page 34). 5. Remove the optical drive (Removing an Optical Drive on page 53). 6. Disconnect the braided cables from the black system board connector labeled F_PANEL. 7. Remove the cable from the clips in the optical drive cage.
System Fan 1. Prepare the computer for disassembly (Preparation for Disassembly on page 32). 2. Remove the access panel (Access Panel on page 33). 3. Lay the computer on its side with the rear facing toward you. 4. Disconnect the cable from the red/brown system board connector labeled SYS_FAN1. 5. Remove the four Phillips screws that secure the fan to the chassis, rotate the top of the fan forward, and then remove the fan from the chassis. NOTE: HP Pro 3015 model shown.
Heat sink assembly HP Pro 3005/3085 1. Prepare the computer for disassembly (Preparation for Disassembly on page 32). 2. Remove the access panel (Access Panel on page 33). 3. Lay the computer on its side with the rear facing toward you. 4. Disconnect the heat sink fan control cable (1) from the white system board connector labeled CPUFAN. 5. Loosen the four captive torx T15 screws (2) that secure the heat sink to the system board. 6.
4. Disconnect the heat sink fan control cable from the white system board connector labeled CPU_FAN. 5. Lift the lever (1) that secures the heat sink latch to the heat sink bracket attached to the system board. 6. After loosening the lever, press downward on the lever to release the square clip (2) from the tab on the heat sink bracket. 7. Use the lever to maneuver the square clip on the opposite side on the heat sink (3) free from the tab on the heat sink bracket. 8.
3. Lay the computer on its side with the rear facing toward you. 4. Disconnect the heatsink control cable from the system board and remove the heatsink Heat sink assembly on page 67). 5. Rotate the locking lever to its full open position (1). 6. Carefully lift the processor from the socket (2). CAUTION: Do NOT handle the pins in the processor socket. These pins are very fragile and handling them could cause irreparable damage. Once pins are damaged it may be necessary to replace the system board.
CAUTION: Heat sink retaining screws should be tightened in diagonally opposite pairs (as in an X) to evenly seat the heat sink on the processor. This is especially important as the pins on the socket are very fragile and any damage to them may require replacing the system board. NOTE: After installing a new processor onto the system board, always update the system ROM to ensure that the latest version of the BIOS is being used on the computer.
6. Inside of the unit, press the power supply release latch on the chassis base, and then lift up the rear of the power supply to disengage it from the chassis. NOTE: HP Pro 3015 shown. 7. Slide the power supply toward the front/bottom of the computer, then lift the power supply out of the computer. To install the power supply, reverse the removal procedure.
3. Lay the computer on its side with the rear facing toward you. 4. Remove the front bezel (Front Bezel on page 34). 5. Remove an expansion cards (Expansion Cards on page 41). 6. Disconnect the power, and data cables from the back of all installed drives. 7. Disconnect all cables from the system board. 8. Remove the eight screws that secure the system board to the chassis. NOTE: HP Pro 3015 shown. System board appearance varies by model. 9.
Battery The battery that comes with your computer provides power to the real-time clock and has a lifetime of about three years. When replacing the battery, use a battery equivalent to the battery originally installed on the computer. The computer comes with a 3-volt lithium coin cell battery. NOTE: The lifetime of the lithium battery can be extended by plugging the computer into a live AC wall socket. The lithium battery is only used when the computer is NOT connected to AC power.
Type 1 Battery Holder 1. Lift the battery out of its holder. 2. Slide the replacement battery into position, positive side up. 3. The battery holder automatically secures the battery in the proper position. 4. Replace the computer access panel. 5. Plug in the computer and turn on power to the computer. 6. Reset the date and time, your passwords, and any special system setups, using Computer Setup. Refer to the Computer Setup (F10) Utility Guide. Type 2 Battery Holder 74 1.
4. Plug in the computer and turn on power to the computer. 5. Reset the date and time, your passwords, and any special system setups, using Computer Setup. Refer to the Computer Setup (F10) Utility Guide. Type 3 Battery Holder 1. Pull back on the clip (1) that holds the battery in place, then remove the battery (2). 2. Insert the new battery and position the clip back in place. 3. Replace the computer access panel. 4. Plug in the computer and turn on power to the computer. 5.
Installing a Security Lock The security locks displayed below and on the following pages can be used to secure the computer.
HP Business PC Security Lock 1. Fasten the security cable by looping it around a stationary object. Figure 6-36 Securing the Cable to a Fixed Object 2. Thread the keyboard and mouse cables through the lock.
3. Screw the lock to the chassis using the screw provided. Figure 6-38 Attaching the Lock to the Chassis 4. Insert the plug end of the security cable into the lock (1) and push the button in (2) to engage the lock. Use the key provided to disengage the lock.
Hood Sensor If the access panel is removed while there is still power to the computer, the hood sensor will cause the system to stop and display the Error 912 message after system reboot and will beep 5 times for 5 seconds. If the alarm sounds, close the access panel, tighten the thumbscrew, then reboot the system. The system will enter the operating system successfully. If the error message persists, press the F10 key immediately when the HP Logo screen is displayed to enter the Computer Setup menu.
HP Chassis Security Kit An optional HP Chassis Security Kit prevents computer components from being removed through an open optical drive bay.
A Connector Pin Assignments This appendix contains the pin assignments for many computer and workstation connectors. Some of these connectors may not be used on the product being serviced.
Headphone Connector and Icon (1/8” miniphone) 1 2 3 Pin Signal 1 (Tip) Audio_left 2 (Ring) Power_Right 3 (Shield) Ground Pin Signal 1 (Tip) Audio_In_Left 2 (Ring) Audio_In_Right 3 (Shield) Ground Pin Signal 1 (Tip) Audio_Out_Left 2 (Ring) Audio_Out_Right 3 (Shield) Ground Line-in Audio Connector and Icon (1/8” miniphone) 1 2 3 Line-out Audio Connector and Icon (1/8” miniphone) 1 2 3 4-Pin Power (for CPU) Connector and Icon 82 Appendix A Connector Pin Assignments Pin Signal
Monitor Connector and Icon Pin Signal Pin Signal 1 Red Analog 9 +5V (fused) 2 Green Analog 10 Ground 3 Blue Analog 11 Not used 4 Not used 12 DDC Serial Data 5 Ground 13 Horizontal Sync 6 Ground 14 Vertical Sync 7 Ground 15 DDC Serial Clock 8 Ground 24-Pin Power Connector 24 13 Front 12 1 Pin Signal Pin Signal Pin Signal Pin Signal 1 +3.3V 7 GND 13 +3.3V 19 GND 2 +3.
PCI Express x1, x4, x8, and x16 PCI Express Connector Pin A Pin Signal Pin Signal Pin Signal Pin Signal Pin Signal 1 PRSNT1 6 JTAG3 11 PERST# 16 PERp0 21 PERp1 2 +12V 7 JTAG4 12 GND 17 PERn0 22 PERn1 3 +12V 8 JTAG5 13 REFCLK+ 18 GND 23 GND 4 GND 9 +3.3V 14 REFCLK- 19 RSVD 24 GND 5 JTAG2 10 +3.
PCI Express x1, x4, x8, and x16 PCI Express Connector Pin B Pin Signal Pin Signal Pin Signal Pin Signal Pin Signal 1 +12V 6 SMDAT 11 WAKE# 16 GND 21 GND 2 +12V 7 GND 12 RSVD 17 22 GND 3 RSVD 8 +3.3 V 13 GND 23 PETp2 24 PETn2 25 GND GND 18 PETp1 4 GND 9 JTAG1 14 PETp0 19 PETn1 5 SMCLK 10 3.
B Power Cord Set Requirements The power supplies on some computers have external power switches. The voltage select switch feature on the computer permits it to operate from any line voltage between 100-120 or 220-240 volts AC. Power supplies on those computers that do not have external power switches are equipped with internal switches that sense the incoming voltage and automatically switch to the proper voltage.
Country-Specific Requirements Additional requirements specific to a country are shown in parentheses and explained below. Country Accrediting Agency Country Accrediting Agency Australia (1) EANSW Italy (1) IMQ Austria (1) OVE Japan (3) METI Belgium (1) CEBC Norway (1) NEMKO Canada (2) CSA Sweden (1) SEMKO Denmark (1) DEMKO Switzerland (1) SEV Finland (1) SETI United Kingdom (1) BSI France (1) UTE United States (2) UL Germany (1) VDE 1.
C Troubleshooting Without Diagnostics This chapter provides information on how to identify and correct minor problems, such as hard drive, optical drive, graphics, audio, memory, and software problems. If you encounter problems with the computer, refer to the tables in this chapter for probable causes and recommended solutions. Safety and Comfort WARNING! Misuse of the computer or failure to establish a safe and comfortable work environment may result in discomfort or serious injury.
To assist you in resolving problems online, HP Instant Support Professional Edition provides you with self-solve diagnostics. If you need to contact HP support, use HP Instant Support Professional Edition's online chat feature. Access HP Instant Support Professional Edition at: http://www.hp.com/ go/ispe. Access the Business Support Center (BSC) at http://www.hp.
● Be sure that all the needed device drivers have been installed. For example, if you are using a printer, you need a driver for that model printer. ● Remove all bootable media (CD or USB device) from the system before turning it on. ● If you have installed an operating system other than the factory-installed operating system, check to be sure that it is supported on the system.
Solving General Problems You may be able to easily resolve the general problems described in this section. If a problem persists and you are unable to resolve it yourself or if you feel uncomfortable about performing the operation, contact an authorized dealer or reseller. WARNING! When the computer is plugged into an AC power source, voltage is always applied to the system board.
Table C-1 Solving General Problems (continued) There is no sound or sound volume is too low. Cause Solution System volume may be set low or muted. 1. Check the F10 BIOS settings to make sure the internal system speaker is not muted (this setting does not affect the external speakers). 2. Make sure the external speakers are properly connected and powered on and that the speakers' volume control is set correctly. 3.
Table C-1 Solving General Problems (continued) Poor performance is experienced. Cause Solution Too many applications running. 1. Close unnecessary applications to free up memory. 2. Add more memory. Some applications run in the background and can be closed by right-clicking on their corresponding icons in the task tray. To prevent these applications from launching at startup, go to Start > Run (Windows XP) or Start > Accessories > Run (Windows Vista) and type msconfig.
Solving Power Problems Common causes and solutions for power problems are listed in the following table. Table C-2 Solving Power Problems Power supply shuts down intermittently. Cause Solution Voltage selector switch on rear of computer chassis (some models) not switched to correct line voltage (115V or 230V). Select the proper AC voltage using the selector switch. Power supply will not turn on because of internal power supply fault. Contact an authorized service provider to replace the power supply.
Solving Hard Drive Problems Table C-3 Solving Hard Drive Problems Hard drive error occurs. Cause Solution Hard disk has bad sectors or has failed. 1. In Microsoft Windows XP, right-click Start, click Explore, and select a drive. Select File > Properties > Tools. Under Error-checking, click Check Now. In Microsoft Windows Vista, right-click Start, click Explore, and right-click on a drive. Select Properties then select the Tools tab. Under Errorchecking click Check Now. 2.
Table C-3 Solving Hard Drive Problems (continued) Computer will not boot from hard drive. Cause Solution Boot order is not correct. Run the Computer Setup utility and change boot sequence in Boot > Boot Device Priority. Hard drive is damaged. See the Worldwide Limited Warranty for terms and conditions. Computer seems to be locked up. Cause Solution Program in use has stopped responding to commands. Attempt the normal Windows “Shut Down” procedure.
Table C-4 Solving Media Card Reader Problems (continued) Can not write to the media card. Cause Solution The media card is a read-only memory (ROM) card. Check the manufacturer’s documentation included with your card to see if it writable. Refer to the previous section for a list of compatible cards. Media card is locked. Locking the media card is a safety feature that prevents writing to and deleting from an SD/ Memory Stick/PRO card.
Solving Display Problems If you encounter display problems, see the documentation that came with the monitor and the common causes and solutions listed in the following table. Table C-5 Solving Display Problems Blank screen (no video). Cause Solution Monitor is not turned on and the monitor light is not on. Turn on the monitor and check that the monitor light is on. Bad monitor. Try a different monitor. The cable connections are not correct.
Table C-5 Solving Display Problems (continued) Blank screen and the computer emits one short beep then one long beep followed by a three second pause. Cause Solution Pre-video memory error. 1. Reseat DIMMs. Power on the system. 2. Replace DIMMs one at a time to isolate the faulty module. 3. Replace third-party memory with HP memory. 4. Replace the system board. Blank screen and the computer emits two short beeps then one long beep followed by a three second pause.
Table C-5 Solving Display Problems (continued) The picture is broken up, rolls, jitters, or flashes. Cause Solution The monitor connections may be incomplete or the monitor may be incorrectly adjusted. 1. Be sure the monitor cable is securely connected to the computer. 2. In a two-monitor system or if another monitor is in close proximity, be sure the monitors are not interfering with each other’s electromagnetic field by moving them apart. 3.
Table C-5 Solving Display Problems (continued) Clicking noise coming from inside a CRT monitor. Cause Solution Electronic relays have been activated inside the monitor. None. It is normal for some monitors to make a clicking noise when turned on and off, when going in and out of standby mode, and when changing resolutions. High pitched noise coming from inside a flat panel monitor. Cause Solution Brightness and/or contrast settings are too high. Lower brightness and/or contrast settings.
Solving Audio Problems If the computer has audio features and you encounter audio problems, see the common causes and solutions listed in the following table. Table C-6 Solving Audio Problems Sound cuts in and out. Cause Solution Processor resources are being used by other open applications. Shut down all open processor-intensive applications. Direct sound latency, common in many media player applications. In Windows XP only: 1. From the Control Panel, select Sounds and Audio Devices. 2.
Table C-6 Solving Audio Problems (continued) Sound does not come out of the speaker or headphones. Cause Solution Computer is in standby mode. Press the power button to resume from standby mode. CAUTION: When attempting to resume from standby mode, do not hold down the power button for more than four seconds. Otherwise, the computer will shut down and you will lose any unsaved data. Internal speaker is disabled in Computer Setup. Enable the internal speaker in Computer Setup.
Table C-7 Solving Printer Problems (continued) Printer will not turn on. Cause Solution The cables may not be connected properly. Reconnect all cables and check the power cord and electrical outlet. Printer prints garbled information. Cause Solution The correct printer driver for the application is not installed. Install the correct printer driver for the application. The cables may not be connected properly. Reconnect all cables. Printer memory may be overloaded.
Solving Keyboard and Mouse Problems If you encounter keyboard or mouse problems, see the documentation that came with the equipment and the common causes and solutions listed in the following table. Table C-8 Solving Keyboard Problems Keyboard commands and typing are not recognized by the computer. Cause Solution Keyboard connector is not properly connected. 1. On the Windows XP Desktop, click Start > Shut Down.
Table C-9 Solving Mouse Problems (continued) Mouse does not respond to movement or is too slow. Cause Solution Mouse may need cleaning. Remove the roller ball cover on the mouse and clean the internal components. Mouse may need repair. See the Worldwide Limited Warranty for terms and conditions. Computer is in standby mode. Press the power button to resume from standby mode. CAUTION: When attempting to resume from standby mode, do not hold down the power button for more than four seconds.
Solving Hardware Installation Problems You may need to reconfigure the computer when you add or remove hardware, such as an additional drive or expansion card. If you install a plug and play device, Windows automatically recognizes the device and configures the computer. If you install a non–plug and play device, you must reconfigure the computer after completing installation of the new hardware. In Windows, use the Add Hardware Wizard and follow the instructions that appear on the screen.
Table C-10 Solving Hardware Installation Problems (continued) The computer emits one short beep then one long beep followed by a three second pause. Cause Solution Memory is installed incorrectly or is bad. CAUTION: To avoid damage to the DIMMs or the system board, you must unplug the computer power cord before attempting to reseat, install, or remove a DIMM. 1. Reseat DIMMs. Power on the system. 2. Replace DIMMs one at a time to isolate the faulty module. NOTE: DIMM2 must always be installed. 3.
Solving Network Problems Some common causes and solutions for network problems are listed in the following table. These guidelines do not discuss the process of debugging the network cabling. Table C-11 Solving Network Problems Wake-on-LAN feature is not functioning. Cause Solution Wake-on-LAN is not enabled. To enable Wake-on-LAN in Windows XP: 1. Select Start > Control Panel. 2. Double-click Network Connections. 3. Double-click Local Area Connection. 4. Click Properties. 5. Click Configure.
Table C-11 Solving Network Problems (continued) Network status link light never flashes. NOTE: The network status light is supposed to flash when there is network activity. Cause Solution No active network is detected. Check cabling and network equipment for proper connection. Network controller is not set up properly. Check for the device status within Windows, such as Device Manager for driver load and the Network Connections applet within Windows for link status. Network controller is disabled. 1.
Table C-11 Solving Network Problems (continued) Network controller stops working without apparent cause. Cause Solution The cable is not securely connected. Ensure that the cable is securely attached to the network connector and that the other end of the cable is securely attached to the correct device. The network controller is defective. Contact an authorized service provider. New network card will not boot.
Solving Memory Problems If you encounter memory problems, some common causes and solutions are listed in the following table. CAUTION: Power may still be supplied to the DIMMs when the computer is turned off. To avoid damage to the DIMMs or the system board, you must unplug the computer power cord before attempting to reseat, install, or remove a DIMM. For those systems that support ECC memory, HP does not support mixing ECC and non-ECC memory. Otherwise, the computer will not boot the operating system.
Table C-12 Solving Memory Problems (continued) The computer emits one short beep then one long beep followed by a three second pause. Cause Solution Memory is installed incorrectly or is bad. 1. Reseat DIMMs. Power on the system. 2. Replace DIMMs one at a time to isolate the faulty module. 3. Replace third-party memory with HP memory. 4. Replace the system board.
Table C-13 Solving CD-ROM and DVD Problems (continued) Movie will not play in the DVD drive. Cause Solution Movie may be regionalized for a different country. See the documentation that came with the DVD drive. Decoder software is not installed. Install decoder software. Damaged media. Replace media. Movie rating locked out by parental lock. Use DVD software to remove parental lock. Media installed upside down. Reinstall media. Cannot eject compact disc (tray-load unit).
Solving USB Flash Drive Problems If you encounter USB flash drive problems, common causes and solutions are listed in the following table. Table C-14 Solving USB Flash Drive Problems USB flash drive is not seen as a drive letter in Windows. Cause Solution The drive letter after the last physical drive is not available. Change the default drive letter for the flash drive in Windows. USB flash drive not found (identified).
Solving Front Panel Component Problems If you encounter problems with devices connected to the front panel, refer to the common causes and solutions listed in the following table. Table C-15 Solving Front Panel Component Problems A USB device, 1394 device, headphone, or microphone is not recognized by the computer. Cause Solution Device is not properly connected. 1. Turn off the computer. 2. Reconnect the device to the front of the computer and restart the computer. The device does not have power.
Solving Internet Access Problems If you encounter Internet access problems, consult your Internet Service Provider (ISP) or refer to the common causes and solutions listed in the following table. Table C-16 Solving Internet Access Problems Unable to connect to the Internet. Cause Solution Internet Service Provider (ISP) account is not set up properly. Verify Internet settings or contact your ISP for assistance. Modem is not set up properly. Reconnect the modem.
Table C-16 Solving Internet Access Problems (continued) Internet takes too long to download Web sites. Cause Solution Modem is not set up properly. Verify that the modem is connected and communicating properly. Windows XP 1. Select Start > Control Panel. 2. Double-click System. 3. Click the Hardware tab. 4. In the Device Manager area, click the Device Manager button. 5. Double-click Modems. 6. Double-click Agere Systems PCI-SV92PP Soft Modem. 7. On the General tab, click Diagnostics. 8.
Solving Software Problems Most software problems occur as a result of the following: ● The application was not installed or configured correctly. ● There is insufficient memory available to run the application. ● There is a conflict between applications. ● Be sure that all the needed device drivers have been installed. ● If you have installed an operating system other than the factory-installed operating system, check to be sure it is supported on the system.
Interpreting Power LED and Beep Codes This section covers the audible codes that may occur before or during POST that do not necessarily have an error code or text message associated with them. WARNING! When the computer is plugged into an AC power source, voltage is always applied to the system board. To reduce the risk of personal injury from electrical shock and/or hot surfaces, be sure to disconnect the power cord from the wall outlet and allow the internal system components to cool before touching.
Resetting the Password Jumper HP Pro 3005/3085 To disable the power-on or setup password features, or to clear the power-on or setup passwords, complete the following steps: 1. Shut down the operating system properly, then turn off the computer and any external devices, and disconnect the power cord from the power outlet. 2. With the power cord disconnected, press the power button again to drain the system of any residual power.
HP Pro 3015 To disable the power-on or setup password features, or to clear the power-on or setup passwords, complete the following steps: 1. Shut down the operating system properly, then turn off the computer and any external devices, and disconnect the power cord from the power outlet. 2. With the power cord disconnected, press the power button again to drain the system of any residual power.
Resetting the CMOS Jumper HP Pro 3005/3085 1. Turn off the computer and any external devices, and disconnect the power cord from the power outlet. The power must be disconnected from the system to clear CMOS. 2. Disconnect the keyboard, monitor, and any other external equipment connected to the computer.
HP Pro 3015 1. Turn off the computer and any external devices, and disconnect the power cords from the power outlet. 2. Disconnect the keyboard, monitor, and any other external equipment connected to the computer. WARNING! To reduce the risk of personal injury from electrical shock and/or hot surfaces, be sure to disconnect the power cord from the wall outlet, and allow the internal system components to cool before touching.
Contacting Customer Support For help and service, contact an authorized reseller or dealer. To locate a reseller or dealer near you, visit http://www.hp.com. NOTE: If you take the computer to an authorized reseller, dealer, or service provider for service, remember to provide the setup and power-on passwords if they are set. Refer to the number listed in the warranty or in the Support Telephone Numbers guide for technical assistance.
D Specifications HP Pro 3005/3085 Table D-1 Specifications – HP Pro 3005/3085 Desktop Dimensions Height 15.14 in 38.46 cm Width 7.27 in 18.46 cm Depth 16.36 in 41.55 cm Approximate Weight 16.8 lb 7.62 kg Operating 50° to 95°F 10° to 35°C Nonoperating -22° to 140°F -30° to 60°C Operating 10-90% 10-90% Nonoperating (38.
Table D-1 Specifications – HP Pro 3005/3085 (continued) Heat Dissipation For 115V/60Mhz: For 230V/50Hz: Maximum 250W PFC+ HV: 250W PFC+ HV: 162.3W or 553.768 BTU/hr or 139.549Kg-cal/hr 160.3W or 546.602 BTU/hr or 137.744Kg-cal/hr 300W PFC+ HV: 300W PFC+ HV: 167.80W or 572.534 BTU/hr or 144.278Kg-cal/hr 164.20W or 560.250 BTU/hr or 141.183Kg-cal/hr 300W Non-PFC 300W Non-PFC 164.70W or 561.956 BTU/hr or 141.613Kg-cal/hr 163.0W or 556.156 BTU/hr or 140.
HP Pro 3015 Table D-2 Specifications – HP Pro 3015 Desktop Dimensions Height 15.14 in 38.46 cm Width 7.27 in 18.46 cm Depth 16.36 in 41.55 cm Approximate Weight 16.8 lb 7.62 kg Operating 50° to 95°F 10° to 35°C Nonoperating -22° to 140°F -30° to 60°C Operating 10-90% 10-90% Nonoperating (38.
Table D-2 Specifications – HP Pro 3015 (continued) For 115V/60Mhz For 230V/50Hz 250W PFC HV ATX: 250W PFC HV ATX: 48.5 W or 165.482 BTU/hr. 48.2 W or 164.4584 BTU/hr. 300W PFC HV ATX: 300W PFC HV ATX: 50.4W or 171.9648 BTU/hr. 50.3W or 171.6236 BTU/hr. 300W NPFC ATX: 300W NPFC ATX: 51.8W or 176.7416 BTU/hr. 52W or 177.424 BTU/hr. 300W 85% EFF ATX: 300W 85% EFF ATX: 43.1W or 147.0572BTU/hr. 43.2W or 147.3984 BTU/hr. 250W PFC HV TFX: 250W PFC HV TFX: 51.9W or 177.0828 BTU/hr. 51.
Index Symbols/Numerics 1394 connector 6 24-pin power pin assignments 83 4-pin power pin assignments 82 A access panel removal and replacement 33 access panel, locked 92 audio connectors 3, 5, 6 audio problems 102 B battery disposal 31 removal and replacement 73 beeps, error codes 88 C cable connections HP Pro 3005/3085 47 HP Pro 3015 48 cable management 46 cable pinouts SATA data 22 cautions AC power 24 cables 30 cooling fan 29 electrostatic discharge 24 keyboard cleaning 28 keyboard keys 29 CD-ROM or DVD
J jumper CMOS 123 password 121 K keyboard cleaning 28 keyboard connector 5 keyboard problems 105 L line-in audio pin assignments 82 line-in connector 5, 6 line-out audio pin assignments 82 line-out connector 5, 6 locks cable lock 76 HP Business PC Security Lock 77 padlock 76 M media card reader features 4 installing 56 removing 55 Media Card Reader problems 96 memory populating sockets 37 removal and replacement 36 specifications 36 memory problems 112 microphone connector 3, 5, 6 microphone pin assignments
setup utility HP Pro 3005/3085 9 HP Pro 3015 16 side channel audio connector 6 software problems 119 servicing computer 29 spare part number tamper-resistent wrench 30 Torx T-15 screwdriver 29 specifications computer 126 memory 36 static electricity 24 subwoofer audio connector 6 system board removal and replacement 71 SATA connectors 22 system board drive connections 51 T tamper-proof screws tool 30 temperature control 27 tools, servicing 29 Torx T15 screwdriver 29 U USB pin assignments 81 USB ports front
