Setup Guide

ManualsBrandsHP ManualsAll in One PrinterHP Photosmart C4599 All-in-One Printer

*Q8400-90052*

Q8400-90052

HP Photosmart C4500 All-in-One series

Abaissez le bac d’alimentation du papier

et ouvrez la porte d’accès aux cartouches

d’impression.

Retirez l’autocollant apposé sur l’écran. Retirez

tout le matériel d’emballage et le ﬁ lm protecteur

du périphérique.

Fermez la porte d’accès aux cartouches

d’impression.

Commencez ici

IMPORTANT : Ne connectez pas le câble USB avant

d’y être invité.

Ce câble est utilisé pour la conﬁ guration USB

et sans ﬁ l.

Comience aquí

Baje la bandeja de papel y la puerta

de los cartuchos de impresión.

Retire la pegatina de la pantalla. Extraiga

todo el material de embalaje y la película

protectora del dispositivo.

Cierre la puerta de los cartuchos

de impresión.

IMPORTANTE: No conecte el cable USB hasta que

se indique.

El cable se utiliza tanto para la conﬁ guración

inalámbrica, como para la USB.

Start Here

Lower both the paper tray and the print

cartridge door.

Remove the sticker from the display. Remove

all packing material and protective ﬁ lm from

the device.

Close the print cartridge door.

IMPORTANT: Do not connect the USB cable until

prompted.

The cable is used for both Wireless and USB setup.

FREN

abc

Summary of content (12 pages)

PAGE 1
HP Photosmart C4500 All-in-One series EN Start Here ES Comience aquí FR Commencez ici 1 EN ES FR 2 a EN ES b a. Lower both the paper tray and the print cartridge door. b. Remove the sticker from the display. Remove all packing material and protective film from the device. c. Close the print cartridge door. IMPORTANT: Do not connect the USB cable until prompted. The cable is used for both Wireless and USB setup. IMPORTANTE: No conecte el cable USB hasta que se indique.
PAGE 2
3 HP Photosmart C4400 series EN Basics Guide ES * 4 FR EN a ES b 5 EN ES • If a prompt appears asking you to set the language and country/region, use the arrows to select your language from the list of languages, and press OK to confirm. Select your country/region, then and OK to confirm. • If a prompt appears asking you to install print cartridges, go to the next step in this guide. FR FR Verify the box contents. The contents of your box may differ.
PAGE 3
6 EN ES FR 7 EN ES FR Open the print cartridge door. Make sure the print carriage moves to the right. If it does not move to the right, turn the device off, then turn it back on again. IMPORTANT: The device must be turned on to insert cartridges. Abra la puerta del cartucho de impresión. Asegúrese de que el carro de impresión se mueve hacia la derecha. Si no se desplaza hacia la derecha, apague el dispositivo y vuélvalo a encender.
PAGE 4
8 a. Hold the cartridges with the HP logo on top. b. Insert the tri-color cartridge in the left cartridge slot and the black cartridge in the right cartridge slot. c. Make sure you push the cartridges in firmly until they snap into place. d. Close the print cartridge door. e. Press OK when prompted to confirm the installation of genuine HP print cartridges. EN a. Sostenga los cartuchos de forma que el logotipo de HP quede situado en la parte superior. b.
PAGE 5
10 EN ES a. Follow the instructions on the display to print the alignment page. b. Lift the lid. Place the top of the alignment page face down in the front right corner of the glass. Close the lid. c. Press OK. FR a. Suivez les instructions qui s’affichent à l’écran pour imprimer la page d’alignement. b. Soulevez le capot. Placez le haut de la page d’alignement, face vers le bas, dans l’angle avant droit de la vitre. Fermez le capot. c. Appuyez sur OK. a.
PAGE 6
12 EN A - 802.11 ES FR B - USB Choose only ONE connection type (A - 802.11/Wireless or B - USB). Go to page 6 for instructions on wireless installation. Go to page 11 for instructions on USB installation. Seleccione sólo UN tipo de conexión (A - 802.11/inalámbrica o B - USB). Vaya a la página 6 para obtener instrucciones sobre la instalación inalámbrica. Vaya a la página 11 para obtener instrucciones sobre la instalación USB. Choisissez UN type de connexion (A - 802.11/Sans fil ou B - USB).
PAGE 7
A2 - 802.11 Windows: EN ES a. Follow the software onscreen instructions, and continue to the next step. b. On the Connection Type screen, make sure to select through the network. IMPORTANT: For the first time install only, no printers will be found during the network search. Click Next to configure your printer on the network. Do not connect the USB cable until prompted. c. When asked, connect your HP All-in-One to your computer using the supplied USB cable.
PAGE 8
A2 - 802.11 Cont’d. Windows: EN ES e. Type the WEP key or WPA passphrase, as requested. You will see a dialog box that confirms that the wireless connection has been established. f. When prompted, disconnect the USB cable. g. If you have additional computers on your network, refer to the Basics Guide for instructions. FR e. Saisissez la clé WEP ou la phrase secrète WPA, comme indiqué. Une boîte de dialogue confirmant l’établissement de la connexion réseau s’affiche. f.
PAGE 9
A2 - 802.11 Mac: EN ES Cont’d. f. When the Select Device screen appears, select your device and then click Continue. The software installation begins, which will take a few minutes. g. When the Setup Assistant appears, click Continue. h. Select Configure Wireless Networking Settings and click Continue. i. When the Network Setup screen appears, select your wireless network name (SSID) and click Continue. j. If the Network Security Setting screen appears, type the WEP key or WPA passphrase.
PAGE 10
EN Wireless Troubleshooting ES Solución de problemas inalámbricos FR Dépannage du mode sans fil www.hp.com/support EN If you are having problems with wireless network setup, you can run the wireless network test, which performs a series of diagnostic tests to determine whether network setup is successful. If an issue is detected, a recommendation on how to correct the issue is included on the printed report. To run the wireless network test and print the report a.
PAGE 11
B1 - USB Windows: EN ES a. Once the USB prompt appears, connect the USB cable to the port on the back of the HP All-in-One, and then to any USB port on the computer. b. Follow the onscreen instructions to complete the software installation. c. To change from USB to wireless, insert the CD again. In the dialog box that is displayed, click Add a device. FR a.
PAGE 12
EN ES USB Troubleshooting Solución de problemas USB FR Dépannage du mode USB www.hp.com/support EN ES FR EN ES FR Problem: (Windows) The Microsoft Add Hardware screen appears. Action: Cancel all screens. Unplug the USB cable, and then insert the HP All-in-One CD. Problema: (Windows) Aparece la pantalla Agregar hardware de Microsoft. Acción: Cierre todas las pantallas. Desconecte el cable USB y, a continuación, introduzca el CD de HP All-in-One.