Setup Guide

ManualsBrandsHP ManualsAll in One PrinterHP Officejet 5610xi All-in-One Printer

HP Photosmart 2600/2700 series all-in-one

User Guide

HP Photosmart 2600/2700 series all-in-one

User Guide

Start Here

Important: Do not connect the USB cable until

Step 16 or software may not install properly.

Remove cardboard and tape

Locate components

Windows CD

Macintosh CD

User Guide

print cartridges

power cord and

adapter

USB cable*

HP Ofﬁ cejet 5600 All-in-One series Setup Guide

*Purchased separately.

The contents of your box may differ.

Follow the steps in order. If you have problems during setup, see Troubleshooting in the last section.

phone cord

bottom paper tray

top (output) tray

Make sure to remove all tape and cardboard on the inside of

the device.

control panel

faceplate (may be

attached)

Summary of content (8 pages)

PAGE 1
Start Here Important: Do not connect the USB cable until Step 16 or software may not install properly. 1 Follow the steps in order. If you have problems during setup, see Troubleshooting in the last section. 2 Remove cardboard and tape Make sure to remove all tape and cardboard on the inside of the device.
PAGE 2
4 Attach the control panel faceplate (if not attached) a 1 b 2 3 a Align the control panel faceplate with the device. b Moving from left to right, press down each of the areas shown in graphic b until you securely attach the faceplate. c Make sure that all buttons are visible and that the edges of the faceplate are even with the device.
PAGE 3
6 Connect the power cord and adapter Important: Do NOT connect the USB cable until Step 16 or software may not install properly. 7 Connect the supplied phone cord Connect one end of the supplied phone cord to the phone port on the left (1-LINE) and the other to a wall jack. To connect an answering machine or use your own phone cord, see the User Guide. 8 On 9 Press the On button and configure a After you press the On button, the green light flashes, and then becomes solid.
PAGE 4
10 Remove tape from both cartridges Pull the pink tab to remove the tape from both print cartridges. Do not touch the copper-colored contacts or retape the cartridges. 11 Insert the tri-color print cartridge a b The device must be On before you can insert the print cartridges. a Slide the tri-color print cartridge into the left slot as shown. b Push the top part of the cartridge firmly up and into the slot until it snaps into place.
PAGE 5
13 a b c Align the print cartridges After you insert the cartridges, a message appears that the device is ready for alignment. a Press OK to print the alignment page. b The alignment page prints. (This may take a few minutes.) c Lift the lid. Place the top of the alignment page face down in the left front corner of the scanner glass. Close the lid. d Press the OK button again to begin alignment. After the On light stops blinking, a message appears on the display to indicate alignment is complete.
PAGE 6
14 Turn on your computer a Turn on your computer, login if necessary, and then wait for the desktop to appear. b Close any open programs. 15 Insert the correct CD Windows Users: Macintosh Users: a Insert the green HP All-in-One Windows CD. b Follow the onscreen instructions to install the software. c On the Connection Type screen, make sure to select directly to this computer. Continue to the next page.
PAGE 7
16 Connect the USB cable Windows Users: a Follow the onscreen instructions until you see the prompt to connect the USB cable. (This may take several minutes.) Once the prompt appears, connect the USB cable to the port on the back of the HP All-in-One, and then to any USB port on your computer. Macintosh Users: a Connect the USB cable to the port on the back of the HP All-in-One, and then to any USB port on your computer. b Double-click the HP All-in-One Installer icon.
PAGE 8
Troubleshooting *Q5610-90132* *Q5610-90132* Q5610-90132 Problem: The Carriage jam message appears on the display. Action: Turn the device off. Check the tray area for cardboard and tape. Make sure the print carriage can move freely. Press the ON button after you have removed all packing materials. Problem: The Remove and check print cartridges message appears after you insert print cartridges. Action: Remove print cartridges. Make sure you remove all tape from the copper contacts.