Hardware Reference Guide HP MP4 Digital Signage Players
© Copyright 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft and Windows are trademarks of Microsoft Corporation in the U.S. and other countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
About This Book WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. NOTE: Text set off in this manner provides important supplemental information.
iv About This Book
Table of contents 1 Product features ............................................................................................................................................. 1 Standard features ................................................................................................................................. 1 Front panel components ....................................................................................................................... 1 Rear panel components ..............
Appendix D Digital signage player operation ............................................................................................... 25 Routine digital signage player care .................................................................................................... 25 Supported orientations ....................................................................................................................... 25 Non-supported orientation .........................................................
1 Product features Standard features Thank you for purchasing an HP digital signage player. We hope you have years of use from our HP MP4 Digital Signage Players. Our goal is to provide you with award-winning digital signage players that are easy to deploy and manage with the power and reliability you expect.
Rear panel components For more information, go to http://www.hp.com and search for your specific digital signage player model to find the model-specific QuickSpecs. Figure 1-2 HP MP4 Digital Signage Player rear panel components (1) DVI-I connector for DVI-D and VGA output (6) Serial connector (2) DisplayPort connector (7) PS/2 connectors (2) (3) Ethernet RJ-45 connector (8) Power cord retention slot (4) Universal serial bus (USB) connectors (2) 2.
3. Press each foot down securely onto a corner of the right side of the digital signage player. Figure 1-3 Installing the rubber feet Installing the stand If the digital signage player will be installed in an vertical orientation and it will not be mounted, the stand should be installed for stability. To install the stand: 1. Turn the unit upside down. 2. Locate the slots on the bottom of the unit into which the tabs on the stand fit. 3.
Removing the stand To remove the stand: 1. Turn the unit upside down. 2. Press the tab (1), and then slide the stand about 1.26 cm (1/2 inch) toward the back of the unit and lift the stand (2) off the unit . Figure 1-5 Removing the stand Using the power cord retention slot To prevent accidental disconnection, press a loop of the power cord into the power cord retention slot.
Using the keyboard Figure 1-7 Keyboard features (1) Caps Lock key Activates/deactivates the Caps Lock feature. (2) Scroll Lock key Activates/deactivates the Scroll Lock feature. (3) Num Lock key Activates/deactivates the Num Lock feature. (4) Ctrl key Use in combination with another key; its function depends on the application software you are using. (5) Windows® Logo Key1 Opens the Start menu in Windows. Use in combination with other keys to perform other functions.
Windows Logo Key Use the Windows Logo Key in combination with other keys to perform certain functions available in Windows operating systems. Windows Logo Key + Tab Switch between open items. Windows Logo Key + e Open My Computer. Windows Logo Key + f Search for a file or folder. Windows Logo Key + Ctrl + f Search for computers. Windows Logo Key + m Minimize all windows. Windows Logo Key + Shift + m Undo minimize all. Windows Logo Key + Break Display the System Properties dialog box.
2 Hardware changes General hardware installation sequence To ensure the proper installation of digital signage player hardware components: 1. Back up any data, if necessary. 2. If the digital signage player is powered on: a. Turn the unit and any other attached devices off. b. Disconnect the power cord from the wall outlet. c. Disconnect any external devices or cables, such as a cable lock.
11. Load any necessary drivers. NOTE: You can download select hardware drivers from HP at http://www.hp.com/country/us/ eng/support.html. 12. Reconfigure the digital signage player, if necessary. Removing and replacing the side access panel and metal side cover Removing the side access panel WARNING! Before removing the side access panel, ensure that the digital signage player is turned off and the power cord is disconnected from the electrical outlet. To remove the left or right access panel: 1.
4. Slide the access panel about 6.35 mm (1/4 inch) toward the bottom of the unit, and then lift the access panel up and off the chassis. Figure 2-2 Removing the side access panel Removing the left metal side cover NOTE: Do not remove the metal side cover to install a SODIMM. The SODIMM compartment is in the right side of the chassis. You must remove the metal side cover to access internal components such as the battery or to install a flash memory module. 1.
Replacing the left metal side cover 1. Place the metal side cover on the chassis, rear edge first, making sure to insert the two tabs of the rear edge into the notches in the chassis (1). 2. Align the tabs on both sides of the cover and press the front edge (2) down firmly until the latch closes. Figure 2-4 Replacing the metal side cover Replacing the side access panel To replace the access panel: 1. Place the access panel on the side of the unit, offset about 6.
3. Turn the chassis upside down. Align the hooks (1) on the underside of the bottom cover with the slots in the chassis and press the cover (2) down and then forward until it locks in place. Figure 2-6 Replacing the bottom cover 4. Replace the stand, if the digital signage player is to be used in the tower orientation.
2. To remove the battery, pull the metal clamp (1) extending above the battery aside and lift the battery (2) out. Figure 2-7 Removing and replacing the internal battery 3. To insert the replacement battery, position it with the positive side facing the chassis wall. Slide the battery down into the slot until the clamp snaps over the edge of the battery. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries.
The memory sockets on the system board can be populated with up to two industry-standard SODIMMs. These memory sockets are populated with at least one preinstalled SODIMM. To achieve the maximum memory support, you can populate the system board with up to 4 GB of memory. For proper system operation, the SODIMMs must be: ● industry-standard 204-pin ● unbuffered non-ECC PC3-12800 DDR3-1600 MHz-compliant ● 1.
2. Pull the front of the access plate up, and lift it off the digital signage player. Figure 2-8 Removing the SODIMM access plate 3. Align the notched edge of the SODIMM with the tab in the socket. CAUTION: To prevent damage to the SODIMM, hold it by the edges only. Do not touch the components on the SODIMM, and do not bend the SODIMM. 4. Hold the SODIMM at approximately a 20-degree angle, and then press the SODIMM into the socket (1) until it is seated.
6. If you are installing the SODIMM in the HP MP4 Digital Signage Player, place a thermal pad on the SODIMM. CAUTION: The thermal pad is required to help cool the SODIMM in the HP MP4 Digital Signage Player. Figure 2-10 Installing the thermal pad in the HP MP4 Digital Signage Player 7. Insert the tab on the front edge of the access plate into its slot (1) and press the plate down lightly to engage the latch (2). Figure 2-11 Replacing the SODIMM access plate 8.
Installing a flash memory module Before beginning the installation process, review General hardware installation sequence on page 7 for procedures you should follow before and after installing or replacing hardware. WARNING! You must remove the left side panel to access the system board. Before removing the side access panel, ensure that the digital signage player is turned off and the power cord is disconnected from the electrical outlet.
2. Align the connector on the flash memory module with the socket on the system board and press the flash memory module into the socket. NOTE: A flash memory module can be installed in only one way. Line up the hole in the flash memory module with the retention post on the system board. Figure 2-13 Inserting the flash memory module 3. Press the module connectors firmly into the flash memory module socket (1), making sure that the retention post on the system board is aligned with the hole in the module.
Installing external drives Various external USB drives are available as options for the MP4 Digital Signage Players. For more information about these drives, visit http://h10010.www1.hp.com/wwpc/us/en/sm/WF12a/ 12454-12454-321959.html, or refer to the instructions that accompany the option. For more information about available options, visit the HP website at http://h10010.www1.hp.com/ wwpc/us/en/sm/WF12a/12454-12454-321959.html.
A Specifications Table A-1 HP MP4 Digital Signage Player Dimensions Width (front to back) 220 mm 8.66 in. Height (top to bottom, without stand) 240 mm 9.45 in Depth (side to side) 40 mm 1.57 in. Approximate Weight 1.53 kg 3.37 lb 10° to 40° C 50° to 104° F -30° to 60° C -22° to 140° F Temperature Range (fanless design)* Operating** (max. rate of change is 10° C per hour or 18° F per hour) Nonoperating (max.
B Security provisions Securing the digital signage player The HP MP4 Digital Signage Players are designed to accept a security cable lock. This cable lock prevents unauthorized removal of the digital signage player, as well as locking the case. To order this option, visit the HP website at http://h30094.www3.hp.com/product.asp? sku=2563044&pagemode=ca. 1. Locate the cable lock slot on the back panel. 2. Insert the cable lock into the slot, and then use the key to lock it.
C Mounting the digital signage player HP Quick Release The HP MP4 Digital Signage Players incorporate four mounting points on one side of the unit. These mounting points follow the VESA (Video Electronics Standards Association) standard, which provides industry-standard mounting interfaces for Flat Displays (FDs), such as flat panel monitors, flat displays, and flat TVs.
To use the HP Quick Release with a VESA-configured digital signage player: 1. Using four 15 mm screws included in the mounting device kit, attach one side of the HP Quick Release to the digital signage player as shown in the following illustration. Figure C-2 Connecting the HP Quick Release to the digital signage player 2. Using four screws included in the mounting device kit, attach the other side of the HP Quick Release to the device to which you will mount the digital signage player.
3. Slide the side of the mounting device attached to the digital signage player (1) over the other side of the mounting device (2) on the device on which you want to mount the digital signage player. An audible 'click' indicates a secure connection. Figure C-4 Connecting the digital signage player NOTE: When attached, the HP Quick Release automatically locks in position. You only need to slide the lever to one side to remove the digital signage player.
Figure C-6 Digital signage player mounted under desk 24 Appendix C Mounting the digital signage player
D Digital signage player operation Routine digital signage player care Use the following information to properly care for your digital signage player: ● Never operate the digital signage player with the outside panel removed. ● Keep the digital signage player away from excessive moisture, direct sunlight, and extreme heat and cold. For information about the recommended temperature and humidity ranges for the digital signage player, see Specifications on page 19.
Figure D-2 Horizontal orientation ● You can lay the digital signage player under a monitor stand with at least one inch of clearance.
Non-supported orientation HP does not support the following orientation for the digital signage player. CAUTION: Non-supported placement of digital signage players could result in operation failure and/ or damage to the devices. CAUTION: Digital signage players require proper ventilation to maintain operating temperature. Do not block the vents. Do not put digital signage players in drawers or other sealed enclosures. Do not place a monitor or other object on top of the digital signage player.
E Electrostatic discharge A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. Preventing electrostatic damage To prevent electrostatic damage, observe the following precautions: ● Avoid hand contact by transporting and storing products in static-safe containers. ● Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.
F Shipping information Shipping preparation Follow these suggestions when preparing to ship the digital signage player: 1. Turn off the digital signage player and external devices. 2. Disconnect the power cord from the electrical outlet, then from the digital signage player. 3. Disconnect the system components and external devices from their power sources, then from the digital signage player. 4.
Index A access panel removing 8 replacing 10 altitude specifications 19 H hardware specifications 19 hardware, upgrades 7 headphone connector location HP Quick Release 21 humidity specifications 19 B battery, replacing 11 I installation sequence 7 installing cable lock 20 digital signage player onto HP Quick Release 21 flash memory module 16 hardware 7 HP Quick Release 21 rubber feet 2 stand 3 C cable lock, installing 20 cautions digital signage player orientation 25, 27 HP Quick Release 23 static elect
side access panel removing 8 replacing 10 side cover removing 9 replacing 10 SODIMM, replacing 12 specifications 19 altitude 19 digital signage player 19 dimensions 19 hardware 19 humidity 19 power output 19 power supply 19 rated output current 19 relative humidity 19 temperature 19 weight 19 stand installing 3 removing 4 supported mounting options 23 supported orientations 25 horizontal 25 under monitor stand 25 vertical 25 T temperature specifications 19 U USB ports location 1, 2 W warnings electric sho
