HP ProLiant ML330 Generation 3 Server Maintenance and Service Guide January 2004 (Fourth Edition) Part Number 322375-004
© 2003, 2004 Hewlett-Packard Development Company, L.P. Microsoft, Windows, and Windows NT are U.S. registered trademarks of Microsoft Corporation. Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein.
Contents About This Guide Audience Assumptions............................................................................................................................... vii Technician Notes........................................................................................................................................ vii Where to Go for Additional Help.............................................................................................................. viii Telephone Numbers ...........
Contents System Board ...........................................................................................................................................2-35 Re-entering the Server Serial Number .....................................................................................................2-37 Chapter 3 Diagnostic Tools Automatic Server Recovery-2....................................................................................................................3-1 Insight Manager 7 .........
Contents Integrated Dual Channel Ultra ATA/100 Adapter with Integrated ATA RAID 0, 1, and 1+0 (ATA Models)......................................................................................................................................................
About This Guide This maintenance and service guide can be used for reference when servicing the HP ProLiant ML330 Generation 3 server. WARNING: To reduce the risk of personal injury from electric shock and hazardous energy levels, only authorized service technicians should attempt to repair this equipment. Improper repairs can create conditions that are hazardous. Audience Assumptions This guide is for service technicians.
About This Guide CAUTION: To properly ventilate the system, you must provide at least 7.6 cm (3.0 in) of clearance at the front and back of the server. CAUTION: The computer is designed to be electrically grounded (earthed). To ensure proper operation, plug the AC power cord into a properly grounded AC outlet only. NOTE: Any indications of component replacement or printed wiring board modifications may void any warranty.
1 Illustrated Parts Catalog Mechanical Components HP ProLiant ML330 Generation 3 Server Maintenance and Service Guide 1-1
Illustrated Parts Catalog Table 1-1: Mechanical Components Item Description Spare Part Number Chassis 1 Front bezel 324713-001 2 Access panel 307549-001 a) Hood panel (right) — b) Access panel (left) — Miscellaneous 3 4 Hardware kit 325036-001 a) Hard drive compartment — b) Media bay drive tray — c) Expansion board knockout — d) Hard drive screws — e) Processor retention brackets* — Miscellaneous plastics kit 176617-001 a) Air baffle — b) Expansion slot retainer* — c) Rubbe
Illustrated Parts Catalog System Components HP ProLiant ML330 Generation 3 Server Maintenance and Service Guide 1-3
Illustrated Parts Catalog Table 1-2: System Components Item Description Spare Part Number Mass Storage Devices 5 IDE CD-ROM drive, 48X 288894-001 6 Diskette drive 233409-001 7 Hard drive a) 36-GB Wide Ultra3 hard drive, 10K RPM (SCSI model) 177986-001 b) 40-GB ATA hard drive (ATA model)* 232008-001 c) 18-GB Wide Ultra3 hard drive, 10K RPM (SCSI model)* 152191-001 d) 80-GB ATA hard drive (ATA model)* 287685-001 e) 160-GB ATA hard drive (ATA model)* 326510-001 Boards 8 PC2100 ECC Registe
Illustrated Parts Catalog Table 1-2: System Components continued Item Description Spare Part Number Miscellaneous 17 Enhanced keyboard* 244000-001 a) European keyboard—UK* 244000-031 b) European keyboard—GR* 244000-041 c) European keyboard—FR* 244000-051 d) Spacesaver keyboard—JP* 244000-291 Signal cable kit* 253826-001 a) ATA ribbon cable assembly — b) Diskette drive cable assembly — c) CD cable assembly — 19 Ultra3 SCSI cable* 289229-001 20 Rack enabling kit* 302569-001 21 Co
2 Removal and Replacement Procedures To service the server, you might need the following: • Torx T-15 screwdriver • Flat-blade screwdriver • Phillips screwdriver • Diagnostics software from the SmartStart CD Safety Considerations Before performing service procedures, review all the safety information. Electrostatic Discharge Information An electrostatic discharge (ESD) can damage static-sensitive devices or microcircuitry.
Removal and Replacement Procedures Rack Warnings and Cautions WARNING: Because the rack allows stacking of computer components on a vertical rather than horizontal plane, be sure that precautions have been taken to provide for rack stability and safety. It is important to follow these precautions providing for rack stability and safety, and to protect both personnel and property. Heed all cautions and warnings throughout the installation instructions provided with the device.
Removal and Replacement Procedures WARNING: Be sure that the AC power supply branch circuit that provides power to the rack is not overloaded. Not overloading AC power to the rack power supply circuit reduces the risk of personal injury, fire, or damage to the equipment. The total rack load should not exceed 80 percent of the branch circuit rating. Consult the electrical authority having jurisdiction over your facility wiring and installation requirements.
Removal and Replacement Procedures System Power Down WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment, remove the power cord to remove power from the system. The front panel Power On/Standby button does not completely shut off system power. Portions of the power supply and some internal circuitry remain active until AC power is removed. CAUTION: Failure to follow these directions could result in damage to equipment or loss of data.
Removal and Replacement Procedures Front Bezel CAUTION: To prevent equipment damage or data loss, be sure that the server is powered down, all cables are disconnected from the back of the server, and the power cord is disconnected from the grounded (earthed) AC outlet before removing the front bezel. To remove the component: 1. Power down the server. Refer to “System Power Down” in this chapter. 2. Pull up on the bezel locking latch until it disengages. 3.
Removal and Replacement Procedures Bezel Blanks WARNING: To reduce the risk of personal injury and to prevent damage to the equipment, before removing the front bezel, be sure that the server is powered down, all cables are disconnected from the back of the server, and the power cord is disconnected from the grounded AC outlet. NOTE: It is not necessary to remove a bezel blank when installing a hard drive into a removable media bay. To remove the component: 1. Power down the server.
Removal and Replacement Procedures Access Panel WARNING: To reduce the risk of injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: Do not operate the server for long periods without the access panel. Operating the server without the access panel results in improper airflow and improper cooling that can lead to thermal damage. NOTE: The interior of the access panel contains labels with information about the server system board.
Removal and Replacement Procedures Air Baffle To remove the component: 1. Power down the server. Refer to “System Power Down” in this chapter. 2. Remove the front bezel. Refer to “Front Bezel” in this chapter. 3. Remove the access panel. Refer to “Access Panel” in this chapter. 4. Remove the air baffle. To replace the component, reverse the removal procedure.
Removal and Replacement Procedures DIMMs To remove the component: 1. Power down the server. Refer to “System Power Down” in this chapter. 2. Remove the front bezel. Refer to “Front Bezel” in this chapter. 3. Remove the access panel. Refer to “Access Panel” in this chapter. 4. Remove the air baffle. Refer to “Air Baffle” in this chapter. 5. Remove the DIMM: a. Press outward on both latches of the memory module socket at the same time to release the DIMM and push it partially out of the socket. b.
Removal and Replacement Procedures Processor and Heatsink/Fan Assembly CAUTION: To reduce the risk of personal injury from hot surfaces, allow the internal server components to cool before touching them. To remove the component: 6. Power down the server. Refer to “System Power Down” in this chapter. 7. Remove the front bezel. Refer to “Front Bezel” in this chapter. 8. Remove the access panel. Refer to “Access Panel” in this chapter. 9. Remove the air baffle. Refer to “Air Baffle” in this chapter. 10.
Removal and Replacement Procedures 13. Remove the heatsink/fan assembly. 14. Open the processor socket locking lever and remove the processor. To replace the component, reverse the removal procedure.
Removal and Replacement Procedures Processor Retention Brackets To remove the components: 1. Power down the server. Refer to “System Power Down” in this chapter. 2. Remove the front bezel. Refer to “Front Bezel” in this chapter. 3. Remove the access panel. Refer to “Access Panel” in this chapter. 4. Remove the air baffle. Refer to “Air Baffle” in this chapter. 5. Remove the processor and heatsink/fan assembly. Refer to “Processor and Heatsink/Fan Assembly” in this chapter. 6.
Removal and Replacement Procedures System Fan To remove the component: 1. Power down the server. Refer to “System Power Down” in this chapter. 2. Remove the front bezel. Refer to “Front Bezel” in this chapter. 3. Remove the access panel. Refer to “Access Panel” in this chapter. 4. Remove the air baffle. Refer to “Air Baffle” in this chapter. 5. Disconnect the fan power cable from the system board fan connector.
Removal and Replacement Procedures 6. Remove the system fan: a. Use a Torx T-15 screwdriver to remove the four mounting screws from the rear of the server. b. Pull the fan out and away from the chassis. To replace the component, reverse the removal procedure.
Removal and Replacement Procedures Power Supply WARNING: To reduce the risk of electric shock or damage to the equipment: • Unplug the power cord before removing the power supply from the server. • Install the power supply before connecting the power cord to the power supply. CAUTION: When sliding the power supply out of the chassis, use one hand to support the weight of the power supply. To remove the component: 1. Power down the server. Refer to “System Power Down” in this chapter. 2.
Removal and Replacement Procedures Media Devices Cable Routing Diagrams SCSI Device Cabling NOTE: Air baffle removed for clarity.
Removal and Replacement Procedures ATA Device Cabling NOTE: Air baffle removed for clarity.
Removal and Replacement Procedures ATAPI Tape Drive Cabling NOTE: Air baffle removed for clarity.
Removal and Replacement Procedures CD-ROM Drive To remove the component: 1. Power down the server. Refer to “System Power Down” in this chapter. 2. Remove the front bezel. Refer to “Front Bezel” in this chapter. 3. Remove the access panel. Refer to “Access Panel” in this chapter. 4. Remove the CD-ROM drive: a. Disconnect the cables from the rear of the drive. Refer to “Cable Routing Diagrams” in this chapter. b. Press the release latches. c. Slide the drive out of the bay.
Removal and Replacement Procedures Media Bay Drive Tray NOTE: The drive trays in the removable media bays can be used to mount internal 3.5-inch devices. The rails mounted inside the drive trays can be removed and used to mount other devices in the removable media bays. To remove the component: 1. Power down the server. Refer to “System Power Down” in this chapter. 2. Remove the front bezel. Refer to “Front Bezel” in this chapter. 3. Remove the access panel. Refer to “Access Panel” in this chapter. 4.
Removal and Replacement Procedures Hard Drive Compartment To remove the component: 1. Power down the server. Refer to “System Power Down” in this chapter. 2. Remove the front bezel. Refer to “Front Bezel” in this chapter. 3. Remove the access panel. Refer to “Access Panel” in this chapter. 4. Disconnect any cabling attached to the drives in the compartment. Refer to “Cable Routing Diagrams” in this chapter. 5. Remove the drive compartment: a. Remove the three shipping screws. b.
Removal and Replacement Procedures Diskette Drive To remove the component: 1. Power down the server. Refer to “System Power Down” in this chapter. 2. Remove the front bezel. Refer to “Front Bezel” in this chapter. 3. Remove the access panel. Refer to “Access Panel” in this chapter. 4. Remove the hard drive compartment. Refer to “Hard Drive Compartment” in this chapter. 5. Remove the diskette drive: a. Disconnect the cables from the rear of the drive. Refer to “Cable Routing Diagrams” in this chapter. b.
Removal and Replacement Procedures Hard Drives To remove the component: 1. Power down the server. Refer to “System Power Down” in this chapter. 2. Remove the front bezel. Refer to “Front Bezel” in this chapter. 3. Remove the access panel. Refer to “Access Panel” in this chapter. 4. Disconnect any cabling attached to the drives in the compartment. Refer to “Cable Routing Diagrams” in this chapter. 5. Remove the hard drive compartment. Refer to “Hard Drive Compartment” in this chapter. 6.
Removal and Replacement Procedures ATA Drive Failure Scenarios IMPORTANT: This section applies only to ATA models of the server. When a drive fails: • Insight Manager notifies you of the drive failure. • If applicable to the operating system, the RAID status icon changes from green to red to indicate that a problem exists. The icon is represented as a round figure wearing sunglasses and is located in the tray bar at the lower right of the screen.
Removal and Replacement Procedures When an online spare is not configured, you must rebuild the array. To rebuild the array: 1. Replace the failed drive. Refer to “Hard Drives” in this chapter. 2. Reboot the server. 3. Use one of the following methods to rebuild the array: — Run the Integrated ATA RAID Configuration Utility by pressing the F8 key, and then run Rebuild. — Let the auto-rebuild take place when the operating system is up and running.
Removal and Replacement Procedures Array Information The Array Information window of the setup screen displays all configured drive arrays. Use this section to create, delete, or edit the existing configurations. The window displays the drive arrays as a node in a tree, like Microsoft® Windows® Explorer. Open the node to display the properties of the array. Press the up arrow and down arrow keys to navigate the properties, and then press the Enter key to edit your selection.
Removal and Replacement Procedures — Stripe Size—changes the stripe size. This field applies only to RAID 0 arrays. The default stripe size is 64 KB. IMPORTANT: RAID configurations do not support a stripe size less than 32 KB. You cannot change the stripe size of an array that has been configured already. — Drive Size—displays the size of the array and cannot be edited. If the array type is stripe, then the drive size is the total of all the drives selected.
Removal and Replacement Procedures Removable Media Bay Devices To remove the component: 1. Power down the server. Refer to “System Power Down” in this chapter. 2. Remove the front bezel. Refer to “Front Bezel” in this chapter. 3. Remove the access panel. Refer to “Access Panel” in this chapter. 4. Remove the air baffle, as needed to access cabling. Refer to “Air Baffle” in this chapter. 5. Disconnect any cabling attached to the drives in the compartment. Refer to “Cable Routing Diagrams” in this chapter.
Removal and Replacement Procedures Power Button/LED Assembly To remove the component: 1. Power down the server. Refer to “System Power Down” in this chapter. 2. Remove the front bezel. Refer to “Front Bezel” in this chapter. 3. Remove the access panel. Refer to “Access Panel” in this chapter. 4. Disconnect the power button cable from the system board. NOTE: Air baffle removed for clarity.
Removal and Replacement Procedures 5. Remove the LED shield: a. Press the locking levers. b. Pull the shield away from the chassis.
Removal and Replacement Procedures 6. Disengage the power button: a. From the front of the chassis, squeeze the sides of the power button to disengage the two retainer clips from the chassis. b. Gently remove the power button from the chassis. 7. Disengage the LEDs: a. Squeeze the sides of the LED to disengage the two retainer clips from the chassis. b. Gently remove the LED from the chassis. c. Repeat for the other LEDs. To replace the component, reverse the removal procedure.
Removal and Replacement Procedures SCSI Controller To remove the component: 1. Power down the server. Refer to “System Power Down” in this chapter. 2. Remove the front bezel. Refer to “Front Bezel” in this chapter. 3. Remove the access panel. Refer to “Access Panel” in this chapter. 4. Remove the SCSI controller: a. Disconnect the SCSI cable attached to the SCSI controller. b. Remove the screw that secures the SCSI controller to the slot. c. Slide the SCSI controller out of the slot.
Removal and Replacement Procedures Expansion Slot Retainer To remove the component: 1. Power down the server. Refer to “System Power Down” in this chapter. 2. Remove the front bezel. Refer to “Front Bezel” in this chapter. 3. Remove the access panel. Refer to “Access Panel” in this chapter. 4. Disconnect any cabling attached to the drives in the compartment. Refer to “Cable Routing Diagrams” in this chapter. 5. Remove the expansion slot retainer: a. Loosen the screw. b.
Removal and Replacement Procedures Battery If the server no longer automatically displays the correct date and time, you may need to replace the battery that provides power to the real-time clock. Always use a battery from the approved spare parts list in Chapter 1, “Illustrated Parts Catalog.” WARNING: The system board contains a lithium battery. A risk of fire and chemical burn exists if the battery is improperly handled.
Removal and Replacement Procedures IMPORTANT: Positive (+) polarity must be positioned up. IMPORTANT: Replacing the system board battery resets the system ROM to its default configuration. After replacing the battery, reconfigure the system through RBSU. Refer to the setup and installation guide. System Board To remove the component: 1. Power down the server. Refer to “System Power Down” in this chapter. 2. Remove the front bezel. Refer to “Front Bezel” in this chapter. 3. Remove the access panel.
Removal and Replacement Procedures 10. Remove the system board: a. Remove the nine screws securing the system board to the chassis. b. Slide the system board toward the front of the server to clear the four alignment standoffs. c. Gently pull the system board out of the chassis. To replace the component, reverse the removal procedure. IMPORTANT: The server serial number must be re-entered through RBSU after replacing the system board.
Removal and Replacement Procedures Re-entering the Server Serial Number After replacing the system board or clearing the NVRAM, the server serial number must be re-entered. 1. During the server startup sequence, press the F9 key to access RBSU. 2. Select the System Options menu. 3. Select Serial Number. The following warning is displayed: WARNING! WARNING! WARNING! The serial number is loaded into the system during the manufacturing process and should NOT be modified.
3 Diagnostic Tools Automatic Server Recovery-2 ASR-2 is a feature that causes the system to restart when a catastrophic operating system error occurs, such as a blue screen, ABEND (abnormal end), or panic. A system fail-safe timer, the ASR-2 timer, starts when the System Management driver, also known as the Health Driver, is loaded. When the operating system is functioning properly, the system periodically resets the timer.
Diagnostic Tools • Multiple drive rebuilding • Special handling of error log, spare drive, and rebuilding After all hard drives have been installed and connected, press the F8 key during startup to run the Integrated ATA RAID Configuration Utility and view the setup screen. ROM will automatically configure drives to RAID 0 if you do not run the F8 utility. To turn off the Integrated ATA RAID Management: • In Microsoft operating systems, right-click on the tray icon and select Quit Spy.
Diagnostic Tools Management Agents The server is equipped with the latest Management Agents, allowing easy manageability of the server through Insight Manager 7 software, and third-party SNMP management platforms. Management agents monitor key subsystems that are instrumental in making health, configuration, and performance data available to the agent software. The agents act upon that data by initiating alarms in the event of faults.
Diagnostic Tools To make selections within RBSU, use the following keys: • Access RBSU by pressing the F9 key when prompted during startup. • Use the arrow keys navigate through the menu system. • Make selections by pressing the Enter key. • Cancel selections by pressing the Esc key. • Save selections and changes by pressing the F10 key. For information on RBSU not found in this guide, refer to the HP ROM-Based Setup Utility User Guide on the Documentation CD.
Diagnostic Tools To install the SmartStart software: 1. Press the F9 key to run RBSU and configure the primary operating system. 2. Locate the SmartStart CD in the HP ProLiant Essentials Foundation Pack. 3. After you power up the server, press the CD-ROM drive eject button. 4. Insert the SmartStart CD into the CD-ROM drive with the labeled side up. Handle the CD by its edges, not by the flat surfaces of the disc. 5. When the busy indicator turns green, the SmartStart sequence begins.
Diagnostic Tools Survey Utility Survey Utility gathers critical hardware and software information on servers running Microsoft Windows NT®, Novell NetWare, SCO OpenServer, or SCO UnixWare operating systems. IMPORTANT: This utility supports operating systems that may not be supported by the server. For operating systems supported by the server, refer to the HP FTP site (ftp://ftp.compaq.com/pub/products/servers/os-support-matrix-310.pdf).
4 Component Identification Front Panel Components Table 4-1: Front Panel Components Item Description 1 CD-ROM drive eject button 2 Diskette drive eject button 3 Power On/Standby button IMPORTANT: The Power On/Standby button does not remove all power from the system. The Standby mode removes power from most of the electronics and the drives, but portions of the power supply and some internal circuitry remain active.
Component Identification Front Panel LEDs Table 4-2: Front Panel LEDs Item LED Description Status 1 CD-ROM drive activity On = Drive activity exists. 2 Diskette drive activity Off = No drive activity exists. 3 System power Green = Server is on. Amber = Server is in standby mode. Off = Server is off; power cord is disconnected. 4 Hard drive activity Green or flashing green = Hard drive activity exists. Off = No hard drive activity exists. 5 NIC link/activity Green = Network link exists.
Component Identification Media Components Table 4-3: Media Components Item Description Location Dimensions 1 IDE CD-ROM drive Media bay 1 13.34 × 4.06 cm 2 Available removable media bay Media bay 2 (5.25 × 1.60 in) 3 Available removable media bay Media bay 3 4 Available removable media bay Media bay 4 5 Diskette drive Hard drive bay 1 8.90 × 2.54 cm 6 Hard drive bay Hard drive bay 2 (3.5 × 1.
Component Identification Rear Panel Components Table 4-4: Rear Panel Components 4-4 Item Description 1 Power connector 2 Mouse connector 3 Keyboard connector 4 Serial connector 5 Video connector 6 USB connectors 7 RJ-45 connector 8 Parallel connector HP ProLiant ML330 Generation 3 Server Maintenance and Service Guide
Component Identification Rear Panel LEDs Table 4-5: Rear Panel LEDs Item LED Description Status 1 Network activity Flashing green = Network activity exists. Off = No network activity exists. 2 Network link Green = Network link exists. Off = No network link exists.
Component Identification System Board Components Table 4-6: System Board Components Item Description Item Description 1 Power supply connectors 12 Remote Insight connector (30-pin) 2 DIMM slot 4 13 System configuration switch 3 DIMM slot 3 14 Expansion slot 4 4 DIMM slot 2 15 Expansion slot 3 5 DIMM slot 1 16 Expansion slot 2 6 Diskette drive connector 17 Expansion slot 1 7 IDE connector (ATAPI devices) 18 Processor fan connector 2 8 ATA/100 RAID primary connector 19 Pro
Component Identification System Configuration Switch CAUTION: Clearing nonvolatile RAM (NVRAM) deletes the system configuration. For instructions on configuring the server, refer to the setup and installation guide.
Component Identification System ID Switch The system ID switch is reserved for use by authorized service providers only. Do not change the indicated default settings. Jumper Settings SCSI Device Jumper Settings No two SCSI devices connected to the same SCSI controller can have the same SCSI ID. If another SCSI device is connected to the controller, check its SCSI ID before beginning the installation procedure for the additional device. Jumpers located on each device set the SCSI ID.
Component Identification System Board LEDs Table 4-8: System Board LEDs Item LED Description Status 1 System fan failure Amber = The system fan has failed or is not installed. Off = The system fan is functioning. 2 Processor 1 failure Amber = Processor 1 has failed or is not installed. Off = Processor 1 is functioning. 3 Processor fan 1 failure Amber = Processor fan 1 has failed or is not installed. Off = Processor fan 1 is functioning.
Component Identification Table 4-8: System Board LEDs continued Item LED Description Status 12 Processor fan 2 failure Amber = Processor fan 2 has failed or is not installed. Off = Processor fan 2 is functioning. 13 AC power Green = The power supply is attached to AC power. Off = The AC power cord is not connected to the power supply, the power supply connector is not attached to the system board, or the power supply has failed.
Component Identification SCSI Cable Components Before performing SCSI cabling procedures, identify the SCSI cable components. The SCSI cable supports up to five SCSI devices and comes with a terminator on the end. One cable is included with SCSI models of the server.
Component Identification ATA Cable Components Before performing ATA cabling procedures, identify the ATA cable components. The type of ATA cable that ships with the server supports up to two ATA devices. Two cables are included with ATA models of the server.
5 Specifications Server Unit Table 5-1: Server Unit Specifications Specification Value Dimensions Height 42.7 cm (16.8 in) Width 19.1 cm (7.5 in) Depth 48.5 cm (19.1 in) Approximate weight (depending on options) 18.18 kg (40 lb) Input specifications Rated input voltage 100 VAC to 199 VAC (U.S.
Specifications Environmental Specifications Table 5-2: Environmental Specifications Specification Value Temperature range* Operating 50°F to 95°F (10°C to 35°C) Shipping -40°F to 158°F (-40°C to 70° C) Maximum wet bulb temperature 82.4°F (28°C) Relative humidity (noncondensing) Operating 10% to 90% Non-operating 5% to 95% * All temperature ratings shown are for sea level. The specification uses an altitude derating of 1°C per 300 m to 3,000 m (1.8°F p er 1,000 ft to 10,000 ft).
Specifications Diskette Drive Table 5-4: 1.44-MB Diskette Drive Specifications Specification Value Size 8.89 cm (3.5 in) LEDs (front panel) Green Read/write capacity per diskette (high/low density) 1.
Specifications Table 5-5: IDE CD-ROM Specifications continued Specification Value Dimensions Height 42.9 mm (1.69 in) Width 208.0 mm (8.2 in) Depth 150.1 mm (5.91 in) Weight 0.950 kg (2.09 lb) Data transfer rate Sustained 150 KBps (single), 1,500 to 4,800 KBps (10X to 32X) Burst 150 KBps to 4,800 KBps Interface IDE (ATAPI) Access times (typical) Full stroke <150 ms Random <100 ms Diameter 12 cm, 8 cm (4.7 in, 3.15 in) Center hole 15 mm (0.6 in) Thickness 1.2 mm (0.
Specifications ATA Hard Drives Table 5-6: ATA Hard Drive Specifications Specification 40 GB 7.2K rpm 80 GB 7.2K rpm 160 GB 7.2K rpm Capacity 40,020.0 MB 80,020.0 MB 160,040.0 MB Height 26.1 mm (1.028 in) 26.1 mm (1.028 in) 26.1 mm (1.028 in) Width 101.6 mm (4 in) 101.6 mm (4 in) 101.6 mm (4 in) Interface Ultra ATA/100 Ultra ATA/100 Ultra ATA/100 Transfer rate synchronous (max) 100 MBps 100 MBps 100 MBps Single track 1.2 ms 3.0 ms 3.0 ms Average <9.00 ms <9.00 ms <9.
Specifications Wide Ultra3 SCSI Hard Drives Table 5-7: Wide Ultra3 SCSI Hard Drive Specifications Specification 18.2 GB 10 K rpm 36.4 GB 10 K rpm Capacity 18,209.3 MB 36,419.2 MB Height 25.4 mm (1 in) 25.4 mm (1 in) Width 101.6 mm (4.0 in) 101.6 mm (4.0 in) Interface Wide Ultra3 SCSI Wide Ultra3 SCSI Transfer rate synchronous (max) 160 MBps 160 MBps Single track 0.7 ms 0.7 ms Average 5.4 ms 5.4 ms Full stroke 11.0 ms 11.
Specifications NC7760 PCI Gigabit Server Adapter (Integrated/Embedded) Table 5-8: NC7760 PCI Gigabit Server Adapter (Integrated/Embedded) Specifications Specification Value Network interface 1000Base-T/100Base-TX/10Base-T Compatibility IEEE 802.3am, 802.3u, 802.3 Data transfer method 32-bit, 33-MHz PCI bus master Network transfer rate 10/100/1000 MBps Connector RJ-45 Compliance PCI 2.2 OS support For specific OS support, refer to www.hp.
Specifications Integrated Dual Channel Ultra ATA/100 Adapter with Integrated ATA RAID 0, 1, and 1+0 (ATA Models) Table 5-10: Integrated Dual Channel Ultra ATA/100 Adapter Specifications Specification Value Protocol UDMA Mode (0-5) PIO Mode (0-4) 5-8 Drives supported Up to 4 ATA (2 devices per channel) Data transfer method 32-bit/33-MHz PCI bus-master Maximum transfer rate per PCI Bus (peak) 133 MBps per channel ATA 100 Cable 80-conductor cable ATA channel transfer rate 100 MBps per channel A
Index A C AC power LEDs 4-10 access panels airflow caution 2-7 part number 1-2 removing and replacing 2-7 air baffle part number 1-2 removing and replacing 2-8 ATA cable assembly, part number 1-5 components 4-12 ATA cable routing 2-17 ATA devices ID, setting 4-8 jumper settings 4-8 ATA drive failure scenarios 2-24 ATA ribbon cable assembly, part number 1-5 ATA/100 RAID connectors 4-6 ATAPI tape drive cabling 2-18 Automatic Server Recovery-2 (ASR-2) 3-1 Autorun Menu 3-5 cable clips, part number 1-2 cable
Index D H devices, jumper settings 4-8 diagnostic tools 3-1 diagnostics utility 2-1, 3-5 DIMM slots, location 4-6 DIMMs part numbers 1-4 removing and replacing 2-9 specifications 5-2 types supported 2-9 diskette drive cable assembly, part number 1-5 connector, system board 4-6 dimensions 4-3 eject button 4-1 LED 4-2 locating 4-3 part number 1-4 specifications 5-3 drive failure scenarios, ATA 2-24 drive tray See media bay drive tray hard drive ATA, specifications 5-5 bays 4-3 LEDs 4-2 part number 1-4 rem
Index L LED shield part number 1-2 removing and replacing 2-30 LEDs front panel 4-2 rear panel 4-5 system board 4-9 M management agents 3-3 mechanical components 1-1 media bay drive tray part number 1-2 removing and replacing 2-20 media bays See removable media bays media components 4-3 memory module See DIMMs miscellaneous plastics kit, part number 1-2 mouse connector 4-4 N NIC LEDs 4-2, 4-5 specifications 5-7 O Online ROM Flash Component Utility 3-6 Option ROM Configuration for Arrays (ORCA) 3-3 overt
Index rubber bumpers, part number 1-2 S safety considerations 2-1 SCSI cable components 4-11 SCSI controller components 4-10 part number 1-4 specifications 5-7 SCSI devices jumper settings 4-8 setting the ID 4-8 SCSI ID, setting 4-8 serial connector 4-4 serial number 2-37 server warnings 2-2 shipping temperatures 5-2 signal cable kit, part number 1-5 slots, locations 4-6 SmartStart installing 3-5 overview 3-4 SmartStart Autorun Menu 3-5 SmartStart Scripting Toolkit 3-5 specifications CD-ROM drive 5-3 DIMM
