Management Agents Events Reference

Event DescriptionEvent SeverityEvent ID
No Cabinet Start, Insufficient IO Fans. Probable Cause: The number of IO fans required
is a hard number. It is not dependent upon the number of entities installed in a
Cabinet. The Utilities Subsystem is not allowing the cabinet to power up due to an
insufficient number of installed IO fans. Recommended Action: Install missing IO
fans, or if proper number installed, troubleshoot IO fan presence detection. SNMP
Trap: hpevtAbortStartIofan - 7784 in HPIFPTRAP.MIB.Error7784
AC power to the PDCA was removed. Data Byte 3 specifies PDCA number. Probable
Cause: Power source supplying AC to the PDCA has failed. Recommended Action:
Troubleshoot AC power problem. SNMP Trap: hpevtAcDeleted - 7786 in
HPIFPTRAP.MIB.Warning7786
Cabinet Main Blower Failed. Probable Cause: Cabinet Blower Failed. Recommended
Action: Replace failed blower module as soon as possible following the Blower
Module Remove and Replace Procedures. SNMP Trap: hpevtBlowrFail - 7791 in
HPIFPTRAP.MIB.Warning7791
48 Volt Converter Failed. Data Byte 3 specifies PDCA number. Probable Cause: The
PDCA identified has failed. This will be evident by many BPS_FAIL codes and
probably a AC_DELETED code in the Event Log. Recommended Action: Contact HP
Support personnel to troubleshoot problem SNMP Trap: hpevtBpsFail48flt - 7793 in
HPIFPTRAP.MIB.Warning7793
Fan failed in designated Bulk Power Supply. Probable Cause: Fan failure or fan
obstructed. Recommended Action: If fan is obstructed, remove obstruction. If no
obstruction, Contact HP Support personnel to troubleshoot problem. SNMP Trap:
hpevtBpsFailFanflt - 7795 in HPIFPTRAP.MIB.Warning7795
1 Side Converter Over Temp. Probable Cause: If this code is not accompanied by
other codes pointing to the same Bulk Power Supply, then it is an internal component
failure. Recommended Action: Contact HP Support personnel to troubleshoot
problem. SNMP Trap: hpevtBpsFailOt - 7796 in HPIFPTRAP.MIB.Warning7796
Bulk Power Supplies are not Redundant. Probable Cause: Entities were added to the
cabinet, increasing the estimated Power Consumption. Or, a non-functional GSP bus
entity has become functional, providing previously missing power consumption
information. Recommended Action: Purchase and install a Bulk Power Supply, if
redundancy is desired. SNMP Trap: hpevtBpsNotRedundant - 7798 in
HPIFPTRAP.MIB.Warning7798
+48V DC has exceeded its upper limit. Probable Cause: The cabinet's 48V power has
exceeded an acceptable upper threshold. Recommended Action: Contact HP Support
personnel to troubleshoot problem. SNMP Trap: hpevtBpsOvervoltage - 7799 in
HPIFPTRAP.MIB.Error7799
+48V DC has fallen below its lower limit. Probable Cause: The cabinet's 48V power
has fallen below an acceptable lower threshold. Recommended Action: Contact HP
Support personnel to troubleshoot problem. SNMP Trap: hpevtBpsUndervoltage -
7803 in HPIFPError7803
Cabinet Fan Failed. Probable Cause: Cabinet Fan Failed. Recommended Action:
Replace failed cabinet fan module as soon as possible following the Cabinet Fan
Module Remove and Replace Procedures. SNMP Trap: hpevtCabFanFail - 7806 in
HPIFPTRAP.MIB.Warning7806
Housekeeping power has exceeded expected levels. Probable Cause: The cabinet's
housekeeping power has risen above an acceptable upper threshold. Recommended
Action: Contact HP Support personnel to troubleshoot problem. SNMP Trap:
hpevtHkpOvervoltage - 7822 in HPIFPTRAP.MIB.Error7822
Housekeeping power has fallen below expected levels. Probable Cause: The cabinet's
housekeeping power has fallen below an acceptable upper threshold. Recommended
Action: Contact HP Support personnel to troubleshoot problem. SNMP Trap:
hpevtHkpUndervoltage - 7823 in HPIFPTRAP.MIB.Error7823
42 Management Agents Event Tables