McDATA® 4Gb SAN Switch for HP p-Class BladeSystem installation guide Part number: AA–RW1XC–TE Third edition: November 2006
Legal and notice information © Copyright 2006 Hewlett-Packard Development Company, L.P. © Copyright 2006 McDATA Corporation. © Copyright 2006. This software includes technology under a license from QLogic Corporation. All rights reserved. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Contents About this guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Intended audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upgrading the interconnect switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing the SAN Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connect the management workstation to the switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Start McDATA Web Server or Element Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Declaration of conformity for products marked with the FCC logo, United States only . . . . . . . . . . . Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Regulatory compliance identification numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures 1 2 3 4 5 6 7 8 9 10 11 12 13 14 McDATA 4Gb SAN Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Front panel switch controls and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switch LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fibre Channel ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About this guide This guide provides information about: • Becoming acquainted with the switch features and capabilities • Installing and configuring a McDATA® 4Gb SAN Switch • Planning a fabric including devices, device access, performance, multiple chassis fabrics, switch services, fabric security, and fabric management. • Diagnosing and troubleshooting switch problems Intended audience This guide is intended for individuals who are responsible for installing and servicing storage area network equipment.
Document conventions and symbols Table 1 Document conventions Convention Element Medium blue text: Figure 1 Cross-reference links and e-mail addresses Medium blue, underlined text (http://www.hp.
HP technical support Telephone numbers for worldwide technical support are listed on the HP support web site: http://www.hp.com/support/.
1 General description This section describes the features and capabilities of the McDATA 4Gb SAN Switch in an HP p-Class BladeSystem server blade chassis. The following topics are described: • Switch LEDs and controls, page 12 • Fibre Channel ports, page 14 • Ethernet port, page 16 • Switch management, page 16 Fabrics are managed with the McDATA Web Server™ switch management application, the Element Manager™ switch management application, and the Command Line Interface (CLI).
Switch LEDs and controls The switch LEDs provide information about the switch’s operational status. These LEDs include the Identifier LED, System Fault LED, and Power LED. The Maintenance button shown in Figure 2 is the only front panel switch control and is used to reset a switch or to recover a disabled switch. Maintenance button Switch LEDs Figure 2 Front panel switch controls and LEDs Switch LEDs The switch LEDs shown in Figure 3 provide status information about switch operation.
System Fault LED (amber) The System Fault LED illuminates to indicate an over temperature condition or a Power-on Self Test (POST) error. Also illuminated on an internal firmware error (heartbeat blink 2), voltage fault, or corrupt configuration error (heartbeat blink 4). Heartbeat LED (green) The Heartbeat LED indicates the status of the internal switch processor and the results of the POST.
Fibre Channel ports The switch has 2 external Fibre Channel ports through which to connect to devices or other switches, and 8 internal ports connecting to the server backplane. Each of the external Fibre Channel ports is served by a Small Form-Factor Pluggable (SFP) optical transceiver and is capable of 1-Gb/s, 2-Gb/s, or 4-Gb/s transmission. SFPs are hot-pluggable. External ports can self-discover both the port type and transmission speed when connected to public devices or other switches.
Port Logged-in LED (green) The Logged-in LED indicates the logged-in or initialization status of the connected devices. After successful completion of the POST, the switch extinguishes all Logged-in LEDs. Following a successful loop initialization or port login, the switch illuminates the corresponding Logged-in LED. This shows that the port is properly connected and able to communicate with its attached devices. The Logged-in LED remains illuminated as long as the port is initialized or logged in.
Ethernet port The Ethernet port shown in Figure 6 is an RJ-45 connector that provides a connection to a management workstation through a 10/100 Base-T Ethernet cable. A management workstation can be a Windows® or a Linux® workstation that is used to configure and manage the switch. You can manage the switch over an Ethernet connection using the McDATA Web Server, CLI, or Simple Network Management Protocol (SNMP). The Ethernet port has two LEDs: the Status LED (green) and the Activity LED (green).
Element Manager IMPORTANT: Element Manager is available only with the Element Manager PFE key. See ”Installing Product Features Enablement keys” on page 35 for more information about installing a PFE key. To obtain the McDATA 4Gb SAN Switch serial number and PFE key, follow the step-by-step instructions on the firmware feature entitlement request certificate for the PFE key. You can obtain a PFE key from the web at: www.webkey.external.hp.com.
General description
2 Planning Consider the following when planning a fabric: • Devices, page 19 • Device access, page 19 • Performance, page 20 • Multiple switch fabrics, page 21 • Switch services, page 23 • Fabric security, page 24 • Fabric management, page 26 Devices When planning a fabric, consider the number of public devices and the anticipated demand. This will determine the number of ports that are needed and in turn the number of switches. See the HP StorageWorks SAN Design Guide for more information.
Each switch has a zoning database that includes the active zone set, all zones, and all zone members. Table 2 describes the zoning database limits.
Latency Switch latency is a measure of how fast a frame travels through the switch from one switch port to another. The factors that affect latency include transmission rate and the source/destination port relationship as shown in Table 3. Table 3 Port-to-port latency Source Rate Destination Rate 1 Gb/s 1 2 4 1 < 0.6 µsec < 0.8 µsec1 < 0.8 µsec1 2 < 0.5 µsec < 0.4 µsec < 0.4 µsec1 4 < 0.4 µsec < 0.3 µsec < 0.3 µsec Based on minimum frame size of 36 bytes.
Domain ID, principal priority, and domain ID lock The following switch configuration settings affect multiple switch fabrics: • Domain ID • Principal priority • Domain ID lock The domain ID is a unique number that identifies each switch in a fabric. The valid domain ID range depends on the interoperability mode: • For Standard, the domain ID can be 97–127. The default is 97. • For McDATA Fabric Mode, the domain ID can be 1–31. The default is 1.
Switch services You can configure your switch to suit the demands of your environment by enabling or disabling a variety of switch services. Familiarize yourself with the following switch services and determine which ones you need. IMPORTANT: The SSL and SSH services can be managed only with Element Manager, which requires the Element Manager PFE key, and the CLI. See ”Installing Product Features Enablement keys” on page 35 for more information about installing a PFE key.
Fabric security An effective security profile begins with a security policy that states the requirements. A threat analysis is needed to define the plan of action, followed by an implementation that meets the security policy requirements. Internet portals, such as remote access and e-mail, usually present the greatest threats. Fabric security should also be considered when defining the security policy.
Switch and port binding IMPORTANT: Switch binding is available only with the McDATA SANtegrity Enhanced PFE key. Switch binding and port binding can be managed only with the CLI and Element Manager. Element Manager also requires a PFE key. See ”Installing Product Features Enablement keys” on page 35 for more information about installing a PFE key.
User account security User account security consists of the administration of account names, passwords, expiration date, and authority level. If an account has Admin authority, all management tasks can be performed by that account in McDATA Web Server, Element Manager, and the Telnet CLI. Otherwise only monitoring tasks are available. The default account name, admin, is the only account that can create or change account names and passwords.
3 Installation The McDATA 4Gb SAN Switch for HP p-Class BladeSystem provides integrated Fibre Channel switch connectivity for single and dual density p-Class blade servers. The switch is compatible with any combination of server blade models in the HP BladeSystem enclosure that connects to the Ethernet Interconnect switch. The Fibre Channel signal conditioning cards provide Fibre Channel signal pass-through connectivity to ProLiant Blade servers.
Fabric management workstation Table 4 lists the requirements for fabric management workstations running McDATA Web Server. Table 4 Management workstation requirements Component Requirement Operating System Windows® Server 2000, Windows Server 2003 SP1, Windows XP® Red Hat® Enterprise Linux® 3 and 4 Memory 256 MB or more Processor 500 MHz or faster Hardware RJ-45 Ethernet port Internet Browser Microsoft Internet Explorer® 5.0 or later Netscape® Navigator® 4.72 or later Mozilla™ 1.
Installing the SAN Switch Remove the protective foam from the prongs on the back of the SAN Switch. Install the SAN Switch into the back of the Interconnect switch. The handle of the SAN Switch should always be on the left.
Connect the management workstation to the switch Connect the management workstation to the switch in one of the following ways: • Indirect Ethernet connection from the management workstation to the switch RJ-45 Ethernet connector through an Ethernet switch or a hub. This requires a 10/100 Base-T straight cable as shown in Figure 8. With this method, you can manage the switch with the McDATA Web Server application or the CLI.
Configure the switch You can configure the switch using the McDATA Web Server application, the Element Manager application, or the CLI. Using McDATA Web Server or Element Manager, select the Open Configuration Wizard option in the Initial Start Dialog. Click Proceed to configure the switch.
Cable devices to the switch Two 4-Gb SFPs ship with each McDATA 4Gb SAN Switch. It is recommended that you use these SFPs rather than the 2-Gb SFPs that ship with the BladeSystem. Connect cables to the SFP transceivers and their corresponding devices as shown in Figure 9, and then energize the devices. Device HBAs can have SFP (or Small Form-factor Fixed (SFF)) transceivers or GigaBit Interface Converters (GBIC).
Using McDATA Web Server or Element Manager to install firmware Installing firmware involves loading, unpacking, and activating the firmware image on the switch. McDATA Web Server and Element Manager do this in one operation. To provide consistent performance throughout the fabric, ensure that all McDATA 4Gb SAN Switch for HP p-Class BladeSystem switches are running the same version of firmware. Verify that this version of firmware is compatible with the firmware of other McDATA switch models in the fabric.
Using the CLI to install firmware To install firmware using the CLI when a FTP server is present on the management workstation, use the Firmware Install command. See the McDATA 4Gb SAN Switch for HP p-Class BladeSystem command line interface guide for information about this command. This command disrupts fabric traffic. 1. Enter the firmware install command to download the firmware from a remote host to the switch, install the firmware, then reset the switch to activate the firmware.
Installing Product Features Enablement keys A PFE key is a password that you can purchase from your switch distributor or authorized reseller to enable particular features in your switch. The following features are available with a PFE key: • SANtegrity Enhanced: Enables device security on the switch. • Element Manager: Enables the Element Manager switch management application through HAFM.
Installation
4 Diagnostics and troubleshooting Diagnostic information about the switch is available through the switch LEDs and the port LEDs. Diagnostic information is also available through the McDATA Web Server and CLI event logs and error displays. This section describes the following types of diagnostics: • ”Switch diagnostics” on page 37 describes the Power LED and System Fault LED indications. • ”Power-on Self Test diagnostics” on page 38 describe the Heartbeat LED and the port Logged-in LED indications.
Power-on Self Test diagnostics The switch performs a series of tests as part of its power-on procedure. The POST diagnostic program performs the following tests: • Checksum tests on the boot firmware in Programmable Read Only Memory (PROM) and the switch firmware in flash memory • Internal data loopback test on all ports • Access and integrity test on the Application Specific Integrated Circuit (ASIC) During the POST, the switch logs any errors encountered. Some POST errors are critical, others are not.
Configuration file system error blink pattern A configuration file system error blink pattern is 4 blinks followed by a two second pause. The 4-blink error pattern indicates that a configuration file system error has occurred, and that the switch configuration file must be recreated. See ”Recovering a switch using maintenance mode” on page 43 for more information. 2 seconds To recreate the configuration file: CAUTION: Recreating the configuration file deletes all switch configuration settings. 1.
or telnet switchname xxx.xxx.xxx.xxx is the switch IP address and switchname is the switch name associated with the IP address. f. Enter an account name and password when the Telnet window prompts you for a login. The default account name is admin. The default password is password. g. Enter the following command to open an Admin session to acquire the necessary authority. McDATA4GbSAN $>admin start h. Enter the following command to restore the configuration file.
E_Port isolation E_Port isolation can be caused by the following: • Security failure • Port type is F_Port or FL_Port and is connected to another switch (should be configured as G or GL) • Conflicting domain IDs • Incompatible fabric interop modes • Conflicting timeout values • Conflicting zone membership between active zone sets See the McDATA 4Gb SAN Switch for HP p-Class BladeSystem user guide or the McDATA 4Gb SAN Switch for HP p-Class BladeSystem command line interface guide for information about how t
Excessive port errors The switch can monitor a set of port errors and generate alarms based on user-defined sample windows and thresholds. These port errors include: • Cyclic Redundancy Check (CRC) errors • Decode errors • ISL connection count • Excessive device logins • Excessive device logouts • Loss-of-signal errors Port threshold alarm monitoring is disabled by default.
Recovering a switch using maintenance mode A switch can become inoperable or unmanageable for the following reasons: • Firmware becomes corrupt • IP address is lost • Switch configuration becomes corrupt • Forgotten password In these specific cases, you can recover the switch using maintenance mode. Maintenance mode temporarily returns the switch IP address to 10.0.0.1 and provides opportunities to perform the following procedures: • Unpack a firmware image file.
Exiting maintenance mode (option 0) The Exit option ends the current login session. Enter the maintenance mode account name and password (prom, prom) to log in again. Momentarily press and release the Maintenance button, or power cycle the switch to return to normal operation. Unpacking the firmware image file in maintenance mode (option 1) The Image Unpack option unpacks and installs new firmware when the current firmware has become corrupt.
Recreating the switch file system in maintenance mode (option 6) The Remake Filesystem option resets the switch to the factory default values including user accounts and zoning. In the event of a loss of power, the switch configuration may be corrupted, in which case the file system on which the configuration is stored must be re-created.
Diagnostics and troubleshooting
A Specifications This appendix contains the specifications for the McDATA 4Gb SAN Switch. See ”General description” on page 11 for the location of all connections, switches, controls, and components. Fibre Channel specifications Table 5 Fibre Channel specifications Item Specification Fibre Channel protocols FC-PH Rev. 4.3 FC-PH-2 FC-PH-3 FC-AL Rev 4.6 FC-AL-2 Rev 7.0 FC-FLA FC-GS FC-GS-2 FC-GS-3 FC-FG FC-Tape FC-VI FC-SW-2 FC Element MIB RFC 2837 Fibre Alliance MIB Version 4.
Table 5 Fibre Channel specifications (continued) Item Specification System processor Integrated IBM™ PowerPC® PPC405 core Fabric Latency (intra-switch) • 1-Gb/s to 1-Gb/s < 0.6 µsec • 2-Gb/s to 2-Gb/s < 0.4 µsec • 4-Gb/s to 4-Gb/s < 0.2 µsec Bandwidth • Point-to-point 212 MB, Full Duplex @ 1-Gb/s 425 MB, Full Duplex @ 2-Gb/s 850 MB, Full Duplex @ 4-Gb/s • Aggregate (single switch) Up to 8.
Dimensions Table 8 Dimensional specifications Item Specification Width 1.5” (38.1 mm) Height 4.75” (120.65 mm) Depth 3.4” (86.4 mm) Weight 1.94 lb (0.88 kg) Electrical Table 9 Electrical specifications Item Specification Operating voltage 3.3 VDC Power source loading (maximum) 3.75 A Heat output (maximum) 12.
Regulatory certifications Table 11 Regulatory certifications Item Specification Safety standards UL60950:2000 CSA C22.2 No.
B Factory configuration defaults This appendix describes the factory default configurations.
Factory port configuration The Show Config Port command displays port configuration values.
Factory port threshold alarm configuration The Show Config Threshold command displays threshold alarm configuration values. If the ThresholdMonitoringEnabled parameter is disabled (False), none of the individual threshold monitoring parameter settings can be applied.
Factory zoning configuration The Show Config Zoning command displays zoning configuration values. Table 15 Factory zoning configuration Parameter Default InteropAutoSave True DefaultZone1 False 1. Available only when InteropMode is McDATA Fabric Mode. Factory SNMP configuration The Show Setup SNMP command displays SNMP configuration values.
Factory RADIUS configuration The Show Setup Radius command displays RADIUS configuration values. Table 17 Factory RADIUS configuration Parameter Default DeviceAuthOrder Local UserAuthOrder Local TotalServers 0 DeviceAuthServer False UserAuthServer False AccountingServer False ServerIPAddress 10.0.0.1 ServerUDPPort 1812 Timeout 2 seconds Retries 0 SignPackets False Factory switch service configuration The Show Setup Services command displays switch service configuration values.
Factory system configuration The Show Setup System command displays system configuration values. Table 19 Factory system configuration Parameter Default Ethernet network discovery Static Ethernet network IP address 10.0.0.1 Ethernet network IP mask 255.0.0.0 Ethernet gateway address 10.0.0.254 Admin timeout 30 minutes Inactivity timeout 0 LocalLogEnabled True RemotelogEnabled False RemoteLogHostAddress 10.0.0.254 NTPClientEnabled False NTPServerAddress 10.0.0.
C Regulatory compliance and safety This appendix contains the regulatory compliance and safety information for the McDATA 4Gb SAN Switch. Regulatory compliance Federal Communications Commission notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum.
Declaration of conformity for products marked with the FCC logo, United States only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions regarding your product, visit http://www.hp.com.
Laser product label The optional label in Figure 14 or equivalent may be located on the surface of the HP supplied laser device. This optional label indicates that the product is classified as a CLASS 1 LASER PRODUCT. This label may appear on the laser device installed in your product.
Japanese notice Korean notices Safety Power cords The power cord set must meet the requirements for use in the country where the product was purchased. If the product is to be used in another country, purchase a power cord that is approved for use in that country. The power cord must be rated for the product and for the voltage and current marked on the product electrical ratings label. The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product.
Japanese power cord notice Electrostatic discharge To prevent damage to the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
Waste Electrical and Electronic Equipment directive Czechoslovakian notice Danish notice Bortskaffelse af affald fra husstande i den Europæiske Union Hvis produktet eller dets emballage er forsynet med dette symbol, angiver det, at produktet ikke må bortskaffes med andet almindeligt husholdningsaffald. I stedet er det dit ansvar at bortskaffe kasseret udstyr ved at aflevere det på den kommunale genbrugsstation, der forestår genvinding af kasseret elektrisk og elektronisk udstyr.
English notice Disposal of waste equipment by users in private household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for recycling of waste electrical and electronic equipment.
French notice Élimination des appareils mis au rebut par les ménages dans l'Union européenne Le symbole apposé sur ce produit ou sur son emballage indique que ce produit ne doit pas être jeté avec les déchets ménagers ordinaires. Il est de votre responsabilité de mettre au rebut vos appareils en les déposant dans les centres de collecte publique désignés pour le recyclage des équipements électriques et électroniques.
Hungarian notice Készülékek magánháztartásban történ selejtezése az Európai Unió területén A készüléken, illetve a készülék csomagolásán látható azonos szimbólum annak jelzésére szolgál, hogy a készülék a selejtezés során az egyéb háztartási hulladéktól eltér módon kezelend . A vásárló a hulladékká vált készüléket köteles a kijelölt gy jt helyre szállítani az elektromos és elektronikai készülékek újrahasznosítása céljából.
Lithuanian notice Nolietotu iek rtu izn cin šanas noteikumi lietot jiem Eiropas Savien bas priv taj s m jsaimniec b s Š ds simbols uz izstr d juma vai uz t iesai ojuma nor da, ka šo izstr d jumu nedr kst izmest kop ar citiem sadz ves atkritumiem. J s atbildat par to, lai nolietot s iek rtas tiktu nodotas speci li iek rtotos punktos, kas paredz ti izmantoto elektrisko un elektronisko iek rtu sav kšanai otrreiz jai p rstr dei.
Slovakian notice Slovenian notice Spanish notice Eliminación de residuos de equipos eléctricos y electrónicos por parte de usuarios particulares en la Unión Europea Este símbolo en el producto o en su envase indica que no debe eliminarse junto con los desperdicios generales de la casa. Es responsabilidad del usuario eliminar los residuos de este tipo depositándolos en un "punto limpio" para el reciclado de residuos eléctricos y electrónicos.
Swedish notice Bortskaffande av avfallsprodukter från användare i privathushåll inom Europeiska Unionen Om den här symbolen visas på produkten eller förpackningen betyder det att produkten inte får slängas på samma ställe som hushållssopor. I stället är det ditt ansvar att bortskaffa avfallet genom att överlämna det till ett uppsamlingsställe avsett för återvinning av avfall från elektriska och elektroniska produkter.
Glossary Active zone set The zone set that defines the current zoning for the fabric. Active firmware The firmware image on the switch that is in use. Activity LED A port LED that indicates when frames are entering or leaving the port. Administrative state State that determines the operating state of the port, I/O blade, or switch. The configured administrative state is stored in the switch configuration. The configured administrative state can be temporarily overridden using the CLI.
Fabric security The functions that provide security for fabric users and devices including user account security, and fabric services. Fabric services A component of fabric security that provides for the control of inband management and SNMP on a switch. Fabric view file A file containing a set of fabrics that were opened and saved during a previous McDATA Web Server session. FDMI See Fabric Device Management Interface.
Power On Self Test (POST) The diagnostics that the switch chassis performs at start up. Principal switch The switch in the fabric that manages domain ID assignments. Product Feature Enablement (PFE) key A password that you can purchase from your switch distributor or authorized reseller to enable particular features in your switch. Simple Network Management Protocol (SNMP) An application protocol that manages and monitors network communications and functions.
Index Numerics conventions document 8 text symbols 8 cord.
ESD (electrostatic discharge) (continued) types of damage from 61 Ethernet connection 30 direct connection 30 indirect connection 30 port 16 Status LED 16 European Union, regulatory compliance notice 59 external ports 14 F F_Port 15 fabric management 26, 48 management switch 16 management workstation 28 point-to-point bandwidth 48 port 15 security 24 factory defaults 44 FCC (Federal Communications Commission) Class A Equipment, compliance notice 57 Class B Equipment, compliance notice 57 declaration of con
M maintainability 48 maintenance exit 44 menu 43 mode 13, 38, 43 Maintenance button 12, 13, 43 management server 23 workstation 16, 30 marking 50 McDATA Web Server 16, 23 install firmware 33 start 30 media type 47 memory flash 13 workstation 28 multiple chassis fabrics 21 N Network Time Protocol 23 noise declaration, German 60 non-critical error 38 non-disruptive activation 32 NTP - See Network Time Protocol O operating systems 28 over temperature 40 P parts proper handling 61 storing 61 transporting 61
security (continued) database limits 25 device 25 fabric 24 user account 26 series number, regulatory compliance 58 server blade 14 SFP - See Small Form-Factor Pluggable shock 49 Simple Network Management Protocol description 17 service 23 small form-factor pluggable 15 SNMP - See Simple Network Management Protocol SSH - See Secure Shell SSL - See Secure Socket Layer static electricity 61 static-dissipating work mat 61 static-safe containers storing products 61 transporting products 61 static-sensitive devi
zoning database 20 limits 20 McDATA® 4Gb SAN Switch for HP p-Class BladeSystem installation guide 77
