Specifications

61
Updated
17/10/00
Internal SCSI Cabling
Netfinity 3000 models 71xxxxx to 77xxxxx have a PCI Fast/Wide Ultra SCSI Adapter while models 78xxxxx and up have a PCI Wide Ultra2 SCSI Adapter. All models support up
to four internal SCSI devices through the 16-bit internal connector or 15 external SCSI devices through the 16-bit external 68-pin High Density connector; however, when internal
SCSI devices are installed to the internal connector, only one SCSI device can be supported from the external connector. All models are cabled internally with a four-drop, 16-bit
wide SCSI cable (models 78xxxxx and up have an Ultra2 SCSI cable), with a built-in active terminator at one end. The other end is attached to the internal 68-pin single-ended
connector of the SCSI adapter. On the standard disk drive models, the hard disk drive (HDD) is attached to the cable connector closest to the active terminator. On open bay models
the first disk drive installed should be attached in the same manner. In the event the standard four drop cable is attached to a RAID controller and a dedicated removable media
attachment to the onboard controller is required, an optional, terminated, 16-bit cable is available (Netfinity Two-Drop Internal SCSI Cable P/N 36L9636). This is not an Ultra2
cable, therefore attached devices will operate at Ultra (or slower) speeds. If connecting narrow devices to this cable, additional 68-pin to 50-pin converters (P/N 32G3925) must be
ordered. Some narrow devices include a converter in their ship group.
Netfinity 3000 Internal Hard Disk Drive Configurator
Open Bay Examples
2
Total
Internal
Storage
1
7200RPM Hard Disk Drives (HDDs)
9.1 GB
(P/N 00N8204)
18.2 GB
(P/N 00N8205)
36.4 GB
(P/N 00N8206)
9.1 GB
Note: 9.1GB disk is
standard in models
7x1UExx
- -
18.2 GB 2 1 -
27.3 GB 3 - -
36.4 GB 4 2 1
45.5 GB
-
- -
54.6 GB - 3 -
72.8 GB - 4 2
91 GB - - -
109.2 GB - - 3
145.6 GB
(max)
--4
This table does not represent all possible hard drive configurations.
1. Total Internal Storage listed is within +/- 0.2 GB unless otherwise noted.
2. Select a total storage row and then select the quantity of HDDs from a column corresponding to the appropriate
hard disk drive. When configuring models which include a single 9.1 GB HDD, use the 9.1 GB column and order
one less HDD than the table indicates.
Bay Form
Factor
Height Front
Access
Usage Part
Number
Description RPM Height Bays
Supported
Max.
Qty.
1
133 mm
(5.25”)
HH yes
IDE CD-
ROM
Ultra160 Hard Disk Drives (HDD)
1
2
133 mm
(5.25”)
1
HH yes open 00N8204 9.1GB Ultra160 SCSI HDD 7200 SL 2,3,5,6 4
3
89 mm
(3.5”)
SL yes open 00N8205 18.2GB Ultra160 SCSI HDD 7200 SL 2,3,5,6 4
4
89mm
(3.5”)
SL yes diskette 00N8206 36.4GB Ultra160 SCSI HDD 7200 SL 2,3,5,6 4
5
89mm
(3.5”)
SL
2
no
HDD on drive
models
External Storage Expansion Units
2
Form Factor
6
89 mm
(3.5”)
SL
2
no open 00N6xxx
4
EXP200 Storage Expansion Unit
3
Rack (3U)
1. A 3.5” conversion kit is standard in Bay 2 for installation of 3.5” hard
disk drives.
2. Two slim-line bays can be combined to support a single half-high (HH)
device.
37L5857
EXP200 Rack-to-Tower
Conversion Kit
3
-
37L0xxx
5
EXP200 350 W Redundant Power Supply -
1. Netfinity 3000 models P/N 771UExx and earlier contain an Ultra SCSI controller and cable which limits Ultra2 and Ultra160
HDDs to Ultra bus speeds. Netfinity 3000 models P/N 780UExx and later contain an Ultra2 SCSI controller which limits
Ultra160 HDDs to Ultra2 bus speeds.
2. Not supported by the onboard external SCSI port. Select an optional SCSI controller then refer to see Appendix D: Cables-
Storage Units-Controllers to confirm the controller supports the desired External Storage Expansion Unit and to select a
supported cable. For HDD or other expansion unit options, see the specific expansion unit section.
3. EXP200 includes a single 2 M Ultra2 SCSI cable and a single hot-swap 350W power supply and standard country power cord.
Optional hot-swap EXP200 350W Redundant Power Supply P/N 37L0xxx includes an additional standard country power cord.
To convert an EXP200 to match the system’s tower form factor, EXP200 Rack-to-Tower Conversion Kit P/N 37L5857 is
required.
4. Where ‘xxx’ represents a specific country code: 899=US/French, 900=European/English, 901=European/Spanish,
902=European/French, 903=European/German, 904=Danish/English, 905=Israel/English, 906=Italian/Italian, 907=South Africa/
English, 908=Swiss/English, 909=Swiss/French, 910=Swiss/German, 912=UK/English - Line Cords/ Publication Country Kits
are included throughout.
5. Where ‘xxx’ represents a country specific code:076=Euro/English , 077=Danish/English, 078=Israel/English, 079=Italy/
English, 080=South Africa/English, 081=Swiss/English, 082=UK/English. Line Cords/Publication Kits are included throughout.
Diskette
CD-ROM
Bay 2
Bay 3
Bay 5
Bay 6