Specifications
138
Updated
17/10/00
To access IBM information specific to your country via the World Wide Web, use address: http://www.pc.ibm.com
IBM Netfinity Rack Cabinet and Options
1. P/N 9306900 includes a glass front door and no side panels.
P/N 9306910 includes a perforated front door and side panels.
Direct Rack Mount
1
: Units Supported Examples
IBM Servers
Netfinity 4000R
All Models 1U
3
xSeries 330
All Models 1U
4
xSeries 340 / Netfinity 4500R
All Models 3U
xSeries 230 / Netfinity 5100
Rack Models 5U
xSeries 240 / Netfinity 5600
Rack Models 5U
Netfinity 6000R
All Models 5U
Netfinity 7100
Rack Models 8U
Netfinity 7600
All Models 8U
Netfinity 8500R
All Models 8U
2
IBM Storage Expansion Units
Netfinity EXP15
P/N SE2RXxx 3U
Netfinity EXP200
P/N 00N6xxx 3U
Netfinity EXP300
P/N 19K11xx 3U
IBM Fibre Solutions
RAID Controller Unit
P/N SFCU1xx 4U
FAStT500 Storage Server
P/N 00N69xx 4U
FAStT500 EXP500 Expansion Unit
P/N 00N71xx 3U
SAN FC Managed Hub
P/N 35L1647 1U
8-port Switch
P/N 2109S08 1U
16-port Switch
P/N 2109S16 2U
FAStT200 Storage Server
P/N 19K11xx 3U
IBM Tape Unit Enclosures
NetMEDIA Enclosure
P/N 03K8756 3U
IBM Networking Products
Dial-in Access to LANS
8235-03x 1U
1. Mounting hardware provided with product
2. Netfinity 8500R requires installation of extension kit P/N 36L9703
or 36L9702 when installed in a Rack 9306900/910 or NetBAY22
P/N 9306200 respectively for proper rear door closure clearance.
3. To provide adequate cooling, a blank filler panel should be placed on
the front of any unused rack space. If non-IBM racks are to be used,
assure that both front and rear doors offer approximately 60% open area
uniformly distributed and in line with installed servers. A clearance of 51
to 64-mm (2 to 2-1/2 inches) must be maintained between the front door
and the system unit’s front bezel. The rear door must maintain the same
or greater distance. Clearance between the EIA mounting rails and rack
side covers must be less than 13-mm (1/2-inch) to prevent air re-
circulation from back to front. Non-rack installations are not supported.
4. To provide adequate cooling, Blank Filler Panel Kit (P/N 94G6670)
should be placed on the front of any unused rack space. If non-IBM racks
are to be used, assure that both front and rear doors offer a minimum of
48% open area uniformly distributed and in line with installed servers. A
clearance of 51 to 64-mm (2 to 2-1/2 inches) must be maintained
between the front door and the system unit’s front bezel. The rear door
must maintain the same or greater clearance. Clearance between the EIA
mounting rails and the rack side covers must be less than 13-mm (1/2
inch) to prevent air re-circulation from back to front. Non-rack or
NetBAY3E installations are not supported.
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
31
30
32
33
34
35
36
37
39
40
41
42
38
10
C
1st Console
Switch, if no
monitor
compartment,
or 2nd PDU
1st PDU2nd PDU
42U
Vertical Rack Mount Area
22U
D
A
B
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
21
22
10
A
1st PDU
Special Side Wall
Compartments
D
Mounting Location
for Display and
Keyboard
NetBAY22
P/N 9306200
E
1st Console
Switch, if no
monitor
compartment
New Rack Options
09N4290 NetBAY 1x4 Console Switch
09N4291 NetBAY 2x8 Console Switch
09N4293 NetBAY 7-foot Console Cable Set
37L68xx
1
NetBAY Server Dual Cord Power Distribution Unit
37L68xx
2
NetBAY Rack Power Distribution Unit
37L6885 NetBAY Single Phase Front-End Power Distribution Unit
37L6883 NetBAY Single Phase Front-End Power Distribution Unit with 120V Line Cord
37L6887 NetBAY Three Phase Front-End Power Distribution Unit
1. Where xx provides a country line cord: 65=US, 67=EUR, 69=Den/Switz, 71=Israel, 73=Italy,
65=Saudi Arabia, 75=S/Africa, and P/N 06P6027=UK.
2. Where xx provides a country line cord: 66=US, 68=EUR, 70=Den/Switz, 72=Israel, 74=Italy,
66=Saudi Arabia, 76=S/Africa, and P/N 06P6028=UK.
Note: For a robust rack configurator application access URL http://www.pc.ibm.com/europe/configurators
Rack Enclosure
P/N 9306900
1
,
P/N 9306910
1