HP NetServer LH 3000/3000r Installation Guide
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Contents 1 Setting Up the HP NetServer LH 3000r and LH 3000.................................. 1 Installation Guidelines.................................................................................... 1 Rack Mount Installation ................................................................................. 2 Pedestal Installation ...................................................................................... 4 Configuring the HP NetServer...........................................................
Contents Removing the LH 3000 Covers .................................................................... 36 Replacing the HP NetServer LH 3000 Covers.............................................. 38 4 Installing Mass Storage Devices............................................................... 39 Introduction ................................................................................................. 39 Duplex Board ....................................................................................
Contents 7 Installing Additional Processors............................................................... 71 Introduction ................................................................................................. 71 Configuration Guidelines.............................................................................. 71 Tools Required ............................................................................................ 72 Installing the Processor..............................................
Contents Configuration Assistant...........................................................................111 Express Configuration ............................................................................111 Custom Configuration.............................................................................114 Replicate Configuration ..........................................................................115 NOS Installation ..............................................................................
Contents DiagTools...............................................................................................139 Error Messages ..........................................................................................140 Clearing the System Configuration..............................................................140 Password Problems....................................................................................142 13Alternative Rack Mounting......................................................
Contents Declaration of Conformity (US, EU, Australia) .........................................162 Regulatory Notices - Product Safety ...........................................................163 CD-ROM and Laser Safety Statements...................................................163 Battery Statements .................................................................................165 Noise and Ergonomic Safety Statements ................................................166 C Service and Support........
1 Setting Up the HP NetServer LH 3000r and LH 3000 Installation Guidelines This Installation Guide is for the LH 3000r rack-mount HP NetServer and the LH 3000 pedestal HP NetServer. Rack-mount Orientation LH 3000r Pedestal Orientation LH Figure 1-1. HP NetServers l Observe all warnings and cautions. l Read this chapter before taking the HP NetServer out of its box. It lists what to do and in what order.
Chapter 1 Setting Up the HP NetServer LH 3000r and LH 3000 l Use the removable and reusable rack-mounting handles to move and place the LH 3000r in the rack. Remove them only when you have secured the NetServer to the rack. The LH 3000 has a locked bezel; the LH 3000r does not. Rack Mount Installation Follow the setup steps in the exact order shown below for a successful rack installation. Skip any steps that do not apply to your installation. Figure 1-2. LH 3000r and Bezel 1.
Chapter 1 Setting Up the HP NetServer LH 3000r and LH 3000 3. If you have optional items to add to the HP NetServer (memory, accessory boards, mass storage, or processors), remove covers and the bezel. If not, skip to step 8. Refer to Chapter 3, "Opening and Closing the HP NetServer." 4. If you have items such as a processor and DIMMs to install, HP recommends that you remove the system board assembly from the server chassis and install them at this time.
Chapter 1 Setting Up the HP NetServer LH 3000r and LH 3000 14. Install the Cable Management Arm to the rear of the rack-mounted HP NetServer. Refer to Chapter 8, "Mounting the HP NetServer in the Rack System/E or Rack System/U." 15. Hook up the monitor, keyboard, mouse, and power supplies, if any. Refer to Chapter 9, "Connecting Monitor, Keyboard, Mouse, and Power Supplies," and to the power supply installation guide. 16. Connect external cables. 17. Power up the HP NetServer.
Chapter 1 Setting Up the HP NetServer LH 3000r and LH 3000 Store the empty boxes and packing material in a safe place. This is especially important if you plan to ship the HP NetServer elsewhere for final installation. CAUTION The HP NetServer LH 3000r and LH 3000 each weigh up to 165 pounds (75 kgs). More than one person is required to lift a server. Do not attempt to lift the HP NetServer by yourself. Failure to observe this warning could result in serious injury or damage to the HP NetServer. 2.
Chapter 1 Setting Up the HP NetServer LH 3000r and LH 3000 10. Replace covers and the bezel. Refer to Chapter 3, "Opening and Closing the HP NetServer." 11. Connect the monitor, keyboard, mouse and power supplies. Refer to Chapter 9, "Connecting Monitor, Keyboard, Mouse, and Power Supplies." 12. Connect external cables. 13. Power up the HP NetServer. Refer to Chapter 2, "Controls, Ports, and Indicators." Go to the next section, "Configuring the HP NetServer.
Chapter 1 Setting Up the HP NetServer LH 3000r and LH 3000 2. On your first use of the CD, HP Navigator prompts you to set the time and date and gives you an opportunity to change the display language. NOTE You might also be asked to update your system BIOS. Follow the instructions to do so. 3. Read the Readme File: Select "Readme File" from the HP Navigator Main Menu. The Readme file contains the latest information to help you install your HP NetServer. 4.
Chapter 1 Setting Up the HP NetServer LH 3000r and LH 3000 9. Choose a NOS: Select the NOS to install and the version, if necessary. 10.
Chapter 1 Setting Up the HP NetServer LH 3000r and LH 3000 ◊ Follow the instructions on the screen and in the network operating system’s installation instructions to perform the manual NOS installation. ◊ For Manual NOS Installation Only: Before you perform a manual NOS installation, print out instructions and create NOS-specific driver diskette(s), as follows: a.
Chapter 1 Setting Up the HP NetServer LH 3000r and LH 3000 Shipping the fully-configured HP NetServer Label each cable and component to facilitate re-assembly. l If racked, remove all components from the rack, including external mass storage. l For both rack-mounted and pedestal NetServers, repack the components in the original packing material and prepare them for shipment. CAUTION 10 It is critical to disassemble and repackage all electronic components before reshipment.
2 Controls, Ports, and Indicators Introduction Before installation, familiarize yourself with the controls, ports, and indicators. Front of the Chassis Use the front panel console from the front of the HP NetServer. Front Panel Console Figure 2-1. LH 3000r Bezel and Front Panel Console Reset Front Panel Console Figure 2-2.
Chapter 2 Controls, Ports, and Indicators Front Panel Console Figure 2-3 shows the HP NetServer LH 3000’s Front Panel Console (the HP NetServer LH 3000r is similar, but has no lock). Door reveals this panel Power Switch Lock Power-on LED Reset Switch Secure Mode Switch Reset Secure Mode LED Server Status LEDs Status Screen Escape Enter Scroll Scroll Down Up Figure 2-3. Front Panel Console Table 2-1.
Chapter 2 RESET Or Controls, Ports, and Indicators RESET Resets the NetServer. This switch may be disabled by Secure mode. Secure Mode Indicator Locks system keyboard, monitor display, and control panel to prevent unauthorized use. Go to the Setup utility security menu to configure this feature. Secure Mode LED illuminates when Secure Mode is enabled. Status screen Reports system status. For details, see the following section: "Viewing System Information.
Chapter 2 Controls, Ports, and Indicators Viewing System Information Use the HP NetServer’s status screen and buttons to view system configuration information, a log of current and past conditions, replaceable parts information, adjust screen contrast, and more. NOTE The small door over the Power and Reset buttons prevents someone from accidentally powering down or resetting the NetServer. Open it to use the Power and Reset buttons. Table 2-2.
Chapter 2 Controls, Ports, and Indicators NOTE The status screen displays two lines of an entire menu at a time. This is the entire Main Menu: ***Main Menu**** >Event Log >FW Info >System Info >Component Info >Service >Adjust Contrast Menus beginning with a greater-than symbol (>) indicate sub-menu selections. 2. Use the arrow buttons to move the cursor to your selection and press the Enter button. A cursor highlights the currently selected line. 3.
Chapter 2 Controls, Ports, and Indicators This is a sample event log: ****EventLog**** >008^ POST Error >007^ TempError >006 CPU Failure >005 POST Error >004 Volt Error >003 CPU Failure >002^ POST Error >001 System Boot Each line includes a brief summary of a log entry, including the log entry number. An "^" on a log entry means the problem is current. 3. To read the complete log for an event, use the arrow keys to select the entry and press Enter.
Chapter 2 Controls, Ports, and Indicators FW Info (Firmware Information) Menu The FW Info menu displays the versions of all firmware components in the system. 1. Select FW Info from the Main Menu. A display similar to the one shown below appears on the NetServer’s front panel display. **FW Info*** 2. Use the arrow buttons to scroll down through the rest of the information.
Chapter 2 Controls, Ports, and Indicators Component Info Menu To see the chassis’ part numbers and serial numbers: 1. Select Component Info from the Main Menu. A display similar to the one shown below appears on the status screen: *Component Info* Asset Tag: 2. Use the down-arrow button to scroll through the rest of the information. An example of a full screen display appears below.
Chapter 2 Controls, Ports, and Indicators Adjust Contrast Menu This is the Adjust Contrast display. *Adjust Contrast == {XXXXXXXX}== 1. To decrease contrast, press (Left Arrow). 2. To increase contrast, press (Right Arrow). 3. To save the contrast setting, press Enter. Hard Disk Drive LED Indicators Each disk drive module has two LEDs: one for status and one for activity. You can view these LEDs on the LH 3000 and the LH 3000r with the bezel open.
Chapter 2 Controls, Ports, and Indicators Eject Button Headphone Jack Activity LED CD ROM Drive Flexible Disk Drive Activity LED Access Button Volume Control Internal Drive Bays (Non-hot-swap) Status LED Activity LED Figure 2-4. CD-ROM, Flexible Disk Drive, and Hard Disk Drive LEDs Rear of the Chassis The HP NetServer’s rear panel includes communication ports, the AC power inlet, and the NetServer’s two power supplies cages.
Chapter 2 Controls, Ports, and Indicators Serial Port Remote Management Port Parallel Port Mouse Port Keyboard Port Hot-Plug PCI LEDs LAN Port Monitor Port 1 2 3 4 Power Supplies Power Supply Status LEDs Power Connectors Figure 2-5. Rear Panel of the HP NetServer The optional Redundancy Kit provides a third power supply. Since the HP NetServer requires two power supplies to run, a third power supply helps to prevent service interruptions.
Chapter 2 Controls, Ports, and Indicators LEDs at the Rear of the Chassis PCI Attention LEDs If a hot-plug board needs attention, its LED glows amber. 1 2 3 4 5 6 7 8 Slot 5 needs attention Figure 2-6. Amber Attention LED When an amber PCI LED appears, you must remove the cover to see the power LEDs for each hot plug PCI slot (see Chapter 3, "Opening and Closing the HP NetServer"). PCI Power LEDs Four pairs of very small LEDs are on the I/O board above left of each hot-plug PCI slot.
Chapter 2 Controls, Ports, and Indicators Onboard LEDs Green (Power) LED Amber (Attention) LED Figure 2-8. Light Pipes Display PCI LEDs Table 2-4. PCI Hot Plug LEDs Amber Green Status Indicated Your Action Power to the slot is on, and the slot is operating normally. Do not remove the board from the slot. The slot needs attention, but power to the slot is on. Do not remove the board from the slot. Off The slot needs attention, and power to the slot is off.
Chapter 2 Controls, Ports, and Indicators LAN LEDs The LH 3000 has two LEDs on either side of the RJ-45 connection. Interpret the LEDs in this way: Table 2-6. Local Area Network LED Status Green LED Yellow LED LAN Status: ON/Flashing OFF The LAN is connected and data is being transferred at 10Mbps. ON/Flashing ON The LAN is connected and data is being transferred at 100Mbps. OFF OFF The LAN is not connected or is not operational (see Chapter 12, "Troubleshooting").
Chapter 2 Controls, Ports, and Indicators NOTE Each 16-amp PDU can accommodate a maximum of two NetServers. When the proper power supply is available, connect the NetServer to the AC power source. Power-On Tests The HP NetServer runs a set of diagnostic tests when it is first connected to a power source. If the LH 3000r passes the tests, you will see: HP NetServer LH 3000r If the HP NetServer does not pass the tests, you will see: Display now? Press Enter to view the error message.
Chapter 2 Controls, Ports, and Indicators 2. Follow instructions in your network operating system (NOS) documentation to gracefully shut down all networking software and applications. 3. Press the Power switch to shut down the HP NetServer. See Figure 2-3. Normally, this completes the procedure. Sleep States (ACPI) The sleep states are available if your NOS supports power management based on the ACPI (Advanced Configuration and Power Interface). Sleep state is one of reduced power use.
Chapter 2 Controls, Ports, and Indicators ◊ To go to a fully powered-down state, press the front panel Power switch for more than 4 seconds. ◊ To go to a fully powered-up state, press the power switch for less than 4 seconds (default) and full operation is restored, including the status screen display and the power LED.
3 Opening and Closing the HP NetServer Introduction Use this chapter to see how to open and close the HP NetServer to add components. Components such as DIMMs and processors are on the system board shown outlined below. LH 3000r LH 3000 Figure 3-1. System Board Assembly Location WARNING Before removing covers, disconnect the power cords and unplug telephone cables. If possible, shut down the operating system.
Chapter 3 NOTE Opening and Closing the HP NetServer If the backlight on the LCD display is on, standby power is also on. Tools Required l Torx 15 Driver l Torx 25 Driver (rack-mount only) l An anti-static service kit (3M 8501/8502/8503 or equivalent). This kit includes a static-dissipating work surface, a chassis clip lead, and a wrist strap. Removing the LH 3000r Covers 1. Extend the anti-tip foot from under the front of the rack.
Chapter 3 Opening and Closing the HP NetServer 2. Remove the bezel from the front of the HP NetServer by swinging the bezel open (past 90 degrees) until it releases from the three posts on the bezel hinge. The bezel has three clips that mount onto a hinge assembly, which is secured to the HP NetServer chassis. Figure 3-3. Removing the HP NetServer LH 3000r Bezel 3. Use a Torx 15 screwdriver to unscrew the four screws, as shown in Figure 3-4. 4.
Chapter 3 Opening and Closing the HP NetServer Remove the two screws securing the NetServer to the rack. Cover 1 Remove two screws Securing the Netserver to the rack. Do not remove the two screws securing the bracket to the NetServer. Cover 2 Cover 3 Do not remove the three screws securing the hinge to the Netserver. 4 Figure 3-4. Front of LH 3000r Screw and Cover Locations 1 2 3 Z-Bracket Remove the two screws holding the NetServer to the bracket. Figure 3-5. Remove Z-bracket 5.
Chapter 3 Opening and Closing the HP NetServer 6. At the front of the NetServer, pull the NetServer forward from the rack until you hear the lockout device engage with a click. Locking Latch Figure 3-6. Locking Latch CAUTION The HP NetServer covers are heavy. Support them as you remove them, and allow room to move them away from the HP NetServer and for storage. 7. Remove Cover 1 by loosening the thumbscrew and sliding the cover forward to disengage it. Lift it up and away from the chassis.
Chapter 3 Opening and Closing the HP NetServer Cover 1 Thumbscrew Cover 2 Thumbscrew Cover 3 Figure 3-7. HP NetServer LH 3000r Covers 8. Remove Cover 2 by supporting it with your hand, then loosening the thumbscrew and pulling the cover forward to disengage it. Lift it away from the chassis (see Figure 3-7). 9. Remove Cover 3 by supporting it with your hand, and loosening the thumbscrew with the other hand. Pull the cover forward to disengage it and catch it as it falls away from the chassis.
Chapter 3 Opening and Closing the HP NetServer Replacing the LH 3000r Covers CAUTION Do NOT operate the NetServer for more than thirty minutes with any cover (including power supplies and disk drives) removed. Otherwise, damage to system components may result due to improper cooling airflow. The two large covers (Covers 1 and 3) with handles are interchangeable. To replace them: 1.
Chapter 3 Opening and Closing the HP NetServer Removing the LH 3000 Covers 1. Unlock the bezel, using the supplied key. The bezel connects to the chassis with two snap-in connectors inside its top left and right corners and two tabs that fit into two slots on the bottom of the chassis. 2. Remove the bezel. a. Pull bezel toward you until it unsnaps. b. Lift the bezel forward and upward from the chassis face.
Chapter 3 Opening and Closing the HP NetServer 3. Once you have removed the bezel, remove Cover 1 by loosening the thumbscrew and then pulling the cover forward to disengage it. Lift it outward and away from the chassis (see Figure 3-9). 4. Remove Cover 2 by loosening the thumbscrew, pulling the cover forward and then slightly sideways to disengage it. Lift it up and away from the chassis. 5. Remove the right cover (Cover 3) by loosening the thumbscrew and pulling the cover forward to disengage it.
Chapter 3 Opening and Closing the HP NetServer Replacing the HP NetServer LH 3000 Covers CAUTION Do NOT operate the NetServer for more than thirty minutes with any cover (including power supplies and disk drives) removed. Otherwise, damage to system components may result due to improper cooling airflow. 1. For each of the side covers, insert the two metal tabs, at the end opposite the handle, into the two openings at the top and bottom corners of the chassis.
4 Installing Mass Storage Devices Introduction The HP NetServer standard configuration is: l One hot-swap mass storage cage (primary) ◊ Configured with a single SCSI bus ◊ Installed with requested drives ◊ With filler panels in the slots not occupied by drives l An enclosure for a second hot-swap mass storage cage (secondary) l A flexible disk drive l A CD-ROM 32x drive l Non-hot-swap mass storage shelves Flexible disk drive CD-ROM drive Non-hot-swap drive shelf Secondary hot-swap cage (requires upg
Chapter 4 Installing Mass Storage Devices Duplex Board Preinstalled A small number of systems have a duplex board preinstalled. The duplex board supports dual-bus mass storage configurations. Duplex hot-swap drive configurations and SCSI IDs are later in this chapter. Upgrade If you are installing the duplex board, refer to the HP NetServer Duplex Kit Installation Guide that came with the Duplex Board Accessory Kit for other information.
Chapter 4 Installing Mass Storage Devices SCSI Termination Make sure that SCSI devices you install in both hot-swap and non-hot-swap bays do not have termination. Hot-Swap Cage and Drive Configurations This section describes mass storage configurations. NOTE In the tables below, the absence of a number in the disk drive row indicates a spacer or filler panel is present in a slot. Primary Cage - SCSI A This is a block diagram of the standard LH 3000r cage configuration.
Chapter 4 Installing Mass Storage Devices Secondary Cage - SCSI B This is a block diagram of an optional LH 3000r cage configuration. I/O Board SCSI A PCI Slots SCSI B Secondary Hot-Swap Mass Storage Cage Figure 4-4. Secondary Cage Configuration – Single Bus B NOTE This configuration requires the mass storage upgrade kit. These are hot-swap drive configurations for the secondary cage.
Chapter 4 Installing Mass Storage Devices Primary Cage Dual Bus - SCSI A and B This is a block diagram of the LH 3000r cage duplexed. I/O Board Channel A: Used for Top Half SCSI A of Cage PCI Slots Duplex Boa rd Channel B: SCSI B Used for Bottom Half of Cage Backplane of Primary Hot-Swap Mass Storage Cage Center Line Figure 4-6. Primary Cage Duplexed These are the drive configurations and SCSI IDs for the primary cage duplexed.
Chapter 4 Installing Mass Storage Devices Primary and Secondary Cages Duplexed I/O Board shown with a DAC in PCI slot 5 (Channel X) and 6 (Channel Y) SCSI A SCSI A to Top Half SCSI B Dup lex Boa rd Primary Cage SCSI B to Bottom Half C Channel D to Bottom Half D uplex B oard D Secondary Cage Channel C to Top Half Figure 4-8.
Chapter 4 Installing Mass Storage Devices Pedestal Primary Cage Duplexed I/O Board SCSI A PCI Slots Channel B: Used for Bottom Half of Cage Duplex Boa rd Channel A: Used for Top Half of Cage Backplane of Primary Hot-Swap Mass Storage Cage (Right Drive Bay) Figure 4-10.
Chapter 4 Installing Mass Storage Devices NOTE Once you have configured the HP NetServer, change this boot order using Setup. See Chapter 10, "Configuring the HP NetServer." Use the Symbios Configuration Utility to configure the HP NetServer to use a PCI slot for boot devices. Refer to the Symbios Configuration Utility on the Information Assistant CD-ROM under LH 3000r/Configure/Hardware Configuration Utility/SCSI Configuration Utility.
Chapter 4 Installing Mass Storage Devices CAUTION When installing more than one drive, do not stack drives on your work surface. Hard disk drives are very susceptible to mechanical shock and can be damaged by a drop as short as one-quarter of an inch. Take care when unpacking and handling the drive. If the drop would crack an egg, it will damage the drive. 3. Drive spacers attach to the disk drive module with four small feet. Drive Spacer Figure 4-13.
Chapter 4 Installing Mass Storage Devices Locking tab pivots when the ejector handle is open Light Pipes (fragile) Drive ejector handle Locking Latch Figure 4-14. Readying Drive Module for Installation 5. With the drive ejector handle open, gently slide the module into the cage. Stop when you feel resistance. 6. With even pressure, gently close the ejector handle until the locking latch clicks shut. Figure 4-15.
Chapter 4 Installing Mass Storage Devices NOTE Closing the ejector handle engages the drive with the electrical connector in the hot-swap mass storage cage and seats the drive. 7. If the drive is unseated in the cage after closing the ejector handle, repeat steps 5 and 6. 8. Configure mass storage devices according to Chapter 10, "Configuring the HP NetServer." Removing a Hot-Swap Hard Disk Drive Module CAUTION You must remove the drive slowly to ensure the drive heads are parked prior to removal.
Chapter 4 Installing Mass Storage Devices Installing Non-Hot-Swap Mass Storage Follow this procedure to install a flexible disk drive, CD-ROM, tape backup, or non-hot-swap hard disk drive. Non-hot-swap shelves Figure 4-16. Non-Hot-Swap Shelves CAUTION 50 Leave the drive in its anti-static bag until you are ready to install it. Before handling the drive, touch any unpainted metal surface to discharge static electricity. When you remove the drive from the anti-static bag, handle it only by the frame.
Chapter 4 Installing Mass Storage Devices Follow the setup steps in the exact order shown below for a successful installation. Skip any steps that do not apply to your installation. 1. Log off all users and gracefully shut down the network operating system according to directions in your NOS documentation. 2. Power down the HP NetServer according to the instructions in Chapter 2, "Controls, Ports, and Indicators." 3.
Chapter 4 Installing Mass Storage Devices Connecting SCSI Sub-Systems The second LVD SCSI connector, bus B, can be used to connect to peripheral sub-systems such as the HP RS/12 or DLT tape libraries. NOTE SCSI channel B has SE and LVD connectors. CAUTION Do not mix high voltage differential (HVD) driver and receiver devices with the SE, LVD (Ultra2), or multimode devices on the same SCSI bus.
5 Installing Additional Memory Introduction This chapter describes adding memory to the HP NetServer LH 3000r and LH 3000. The standard configuration ships with one 128 MB DIMM in slot 0. DIMM Socket DIMM Socket DIMM Socket DIMM Socket 0 1 2 3 Figure 5-1. DIMM Sockets on System Board Assembly Memory Guidelines l Add DIMMs of these sizes: ◊ 128 Mb ◊ 256 Mb ◊ 512 Mb ◊ 1 GB l Add memory in any order to the four slots. l You can mix DIMM sizes. For example, you may place a 1 GB DIMM next to a 128 Mb DIMM.
Chapter 5 Installing Additional Memory Tools Required l An anti-static service kit (3M 8501/8502/8503 or equivalent). This kit includes a static-dissipating work surface, a chassis clip lead, and a wrist strap. Installing Memory in the LH 3000r and LH 3000 CAUTION Extend the anti-tip foot prior to any work on a rack-mount server. The installation procedure is the same for the rack-mount and the pedestal HP NetServers once you gain access to the system board assembly. 1.
Chapter 5 Installing Additional Memory LH 3000r LH 3000 Figure 5-2. Location of System Board Assembly WARNING Always disconnect the power cord before removing the covers to avoid exposure to high energy levels that may cause burns when parts are short-circuited by metal objects such as tools or jewelry. Disconnect any telephone cables to avoid exposure to shock hazard from telephone ringing voltages. 5. Unlatch the blue retaining latches to release the board. Blue Retaining Latches Figure 5-3.
Chapter 5 Installing Additional Memory CAUTION The system board assembly weighs approximately 15 lbs. (7 kgs). Removing the board assembly with the assistance of another person is advised. 6. Pull the board out until it clears the chassis guides (see Figures 5-3 and 5-4). Rotate retaining latches and lift system board assembly up and out of the chassis. Figure 5-4.
Chapter 5 Installing Additional Memory 7. Slide the system board assembly from the chassis and place it metal plate side down on an anti-static pad. 8. Install the DIMMs: a. Spread the latches outward on each socket to receive a DIMM. b. Remove a DIMM from its anti-static bag, handling the module by its edges. c. Align the notches on the DIMM with the slot keys on the socket. CAUTION Do not rock the DIMM into place, but apply firm and even pressure.
Chapter 5 Installing Additional Memory Repeat step 8 to install all of the DIMMs for your memory configuration. 9. Carefully reinsert the system board assembly into its guides until the blue latches return to the flat, locked position. Figure 5-6. Install the System Board Assembly 10. Follow the procedure in Chapter 3, "Opening and Closing the HP NetServer," for closing up the server. 11. Reconnect power and cables. 12. Restore HP NetServer to normal operation. This completes the DIMM installation.
6 Installing Additional PCI Boards Introduction This chapter describes how to install accessory boards, during initial installations, into the I/O board. The I/O board is under Cover 1 on the top of the LH 3000r and under the left cover of the LH 3000. If you want to do a "hot" add or "hot" replacement (with the HP NetServer powered up), go to Hot Adding or Replacing Hot-Plug PCI Boards at the end of this chapter.
Chapter 6 Installing Additional PCI Boards The I/O board comprises: • Eight PCI board slots l Four pairs of PCI hot-plug LEDs l Four rectangular separators to ease hot-plug board replacement • Two SCSI connectors, A and B for hot-swap drives l The SE SCSI connector for non-hot-swap drives • The I/O Memory slot, which contains memory used by the Intel i960RD I/O processor for embedded RAID • The Remote Management connector, linking the I/O board to the external connector on the rear panel l Hot-plug c
Chapter 6 Installing Additional PCI Boards l Consider the boot priority prior to installing accessory boards, but after configuring the HP NetServer. l Some accessory board outputs may exceed U.S. National Electrical code (NFPA 70) Class 2 or power source limits and must use appropriate interconnecting cabling in accordance with the National Electrical Code. (All Hewlett-Packard boards comply with Class 2.) l You can configure the NetServer to boot from a PCI-based DAC inserted into a PCI slot.
Chapter 6 Installing Additional PCI Boards Boot Priority Some boards have preferred slot locations. If not, consider the boot order when choosing the accessory board slot in which to install the accessory board. This is the default boot priority for the LH 3000r and LH 3000: 1. IDE CD-ROM drive with a bootable CD-ROM 2. Flexible disk drive with a bootable flexible disk 3. HP NetRAID controller or integrated Embedded SCSI controller 4.
Chapter 6 Installing Additional PCI Boards 1. Read the documentation included with each board and follow any special instructions provided. 2. If necessary, log off all users and gracefully shut down the network operating system according to directions in your NOS documentation. 3. Make sure the HP NetServer is powered off according to the instructions in Chapter 2, "Controls, Ports, and Indicators." 4. Disconnect the power cord and cables, and label each one to support reassembly.
Chapter 6 Installing Additional PCI Boards 8. Release the front board hold-down and remove it. Front board hold-down Figure 6-2. Remove Front Board Hold-Down 9. Remove the slot cover from the target slot (number 3 in this example) by rotating the solid latch first and the latch with the small opening second. NOTE 64 The PCI non-hot-plug slot covers use a black retainer and a blue locking lever to hold the slot cover and board in place, instead of a screw commonly used on HP NetServers.
Chapter 6 Installing Additional PCI Boards Retainer 2 1 Locking Lever 1 3 Non Hot-Plug Slot 3 Figure 6-3. Remove the Slot Cover NOTE After removing the slot cover, leave the retainer and locking lever open so that you can install the board. 10. Install the PCI non-hot-plug board in the slot, which is number 3 in this example.
Chapter 6 Installing Additional PCI Boards Figure 6-4. Install Non-Hot-Plug Board 11. Align the board with its slot along its full length, and push it into the slot with even pressure along the top edge of the board until it is fully seated in its connector. NOTE To prevent EMI problems, ensure each unused PCI slot has a PCI slot cover. If a PCI board is removed and not re-installed, you must install a PCI slot cover. 12. Close the PCI hold-down latch, by reversing the procedure in step 9.
Chapter 6 Installing Additional PCI Boards 15. Follow the procedure in Chapter 3, "Opening and Closing the HP NetServer," for closing up the server. 16. Reconnect power and cables. 17. Power on the HP NetServer according to the respective NOS power-up instructions. NOTE All PCI slots (with the PCI hold-down latch closed) power on and all new boards are recognized by the HP NetServer when it reboots, regardless of the presence of a driver or a PCI Hot-Plug Utility.
Chapter 6 Installing Additional PCI Boards Removing a Hot-Plug Board If you want to remove or replace a hot-plug PCI board, go to "Hot Adding or Replacing Hot-Plug PCI Boards" in the following section. To remove a hot-plug board from the HP NetServer which is not running: 1. Make sure power is off and follow the instructions for accessing the I/O board. 2. Pull the brown plastic slot separator out until you feel resistance (about three-eighths of an inch, or 10mm).
Chapter 6 Installing Additional PCI Boards Hot Adding or Replacing Hot-Plug PCI Boards The PCI Hot-Plug option is NOS-dependent. To use the Hot-Plug option, the PCI board must have a hot-plug compliant driver and a Hot-Plug Utility for the respective NOS. The Hot-Plug Utility is used to turn power off/on to the PCI slot, while the HP NetServer continues to operate normally. Refer to the PCI Hot-Plug Replacement procedures in Information Assistant for the NOS you are using.
7 Installing Additional Processors Introduction The HP NetServer LH 3000/3000r supports two processors in primary and secondary slots. The NetServer ships with one processor and an accompanying VRM in the primary slots. The processor and VRM are on the system board. Primary VRM Configuration Switches Primary Processor Secondary Processor Secondary VRM Figure 7-1. System Board Configuration Guidelines CAUTION Do not remove the processor from its bag until you are ready to install it.
Chapter 7 Installing Additional Processors CAUTION Do not change the processor speed switches as this can result in unreliable or intermittent performance, and data integrity may also be at risk. l Use only processor upgrade kits with the same HP product number. This ensures the processor type, clock speed, and cache size match, and that processor steppings are compatible. l Be sure that the VRM and the processor module associated with it are both in either the primary or the secondary pair of slots.
Chapter 7 Installing Additional Processors 2. If you are installing a processor in a new HP NetServer, skip to step 4; otherwise, shut down the network operating system according to directions in your NOS documentation and power down the HP NetServer according to the instructions in Chapter 2, "Controls, Ports, and Indicators." 3. Disconnect the power cord and cables and, if necessary, label each one to support re-assembly.
Chapter 7 Installing Additional Processors Rotate retaining latches and lift system board assembly up and out of the chassis. ‘ Figure 7-3.
Chapter 7 Installing Additional Processors 7. Slide the system board assembly from the chassis and place it metal plate side down on an anti-static pad. 8. Remove the processor cage cover by releasing the thumbscrew. Set the cover aside. Thumbscrew Figure 7-4.
Chapter 7 Installing Additional Processors 9. Slide the blue plastic release levers forward to free the terminator. 10. Hold the terminator by its edges and lift straight up to remove it. 11. Save the terminator for future use. Terminator Release Levers Figure 7-5. Remove the Terminator 12. Remove the processor from the sealed bag.
Chapter 7 Installing Additional Processors 13. Align the additional processor over the secondary slot so that the heat sink faces towards the center of the enclosure like the processor already installed. Figure 7-6. Install Processor 14. Gently push down on the additional processor until the blue latches return to their closed position. 15. Align the VRM card with the secondary VRM slot. Note that the component side should face away from the VRM already installed.
Chapter 7 Installing Additional Processors 16. Holding the VRM by its edges, insert it into the socket. Figure 7-7. Handle VRM by Edges Figure 7-8.
Chapter 7 Installing Additional Processors 17. Processor speed switches are set for the processor speed that ships with your system. NOTE Only the first four switches set the processor speed. After installing processors, verify that the configuration switches are set correctly. If the switches are not correct, set them accordingly. To set the configuration switches: 18. Locate the configuration switches on the system board. Not Used Clear Config Clear Password CPU Speed CPU Speed CPU Speed 19.
Chapter 7 Installing Additional Processors Table 7-1.
Chapter 7 Installing Additional Processors Figure 7-10. Replace Processor Cage Cover 22. If you removed the system board assembly, re-install the assembly now. CAUTION Processor modules are designed to operate at their stated speed. Do not set the configuration switches to a different speed. Setting the processor speed to another speed may result in unreliable or intermittent performance.
Chapter 7 Installing Additional Processors Figure 7-11. Install the System Board Assembly CAUTION Do not operate the HP NetServer without first installing all covers and the front bezel. Operating the system without all covers in place reduces critical cooling airflow over some components, such as hard disk drives and processors. Operating the system without all covers in place may result in failure of these components. 23.
Chapter 7 Installing Additional Processors Upgrading the Firmware Load the HP NetServer Navigator CD-ROM. It will advise you if the BIOS version on the CD is newer than the BIOS on the HP NetServer and ask you if you want to update the BIOS. Choose Continue, and then NetServer Utilities to update the BIOS if necessary. Testing the Processor After you power on the NetServer, check boot messages to see whether or not the system detects the additional processor.
8 Installing the HP NetServer in the HP Rack System/E or Rack System/U Introduction This chapter describes how to mount the HP NetServer in an HP System/E or /U rack. If you have an older HP System rack, see Chapter 13, "Alternative Rack Mounting," for instructions. (If you are mounting the HP NetServer in a non-HP rack, refer to the separate rack-mounting guide for third-party racks. It is packed in the accessories tray in the HP NetServer’s shipping box.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U NOTE The pedestal HP NetServer LH 3000 cannot be rack-installed without a conversion kit. Contact your HP reseller for information about the HP NetServer LH 3000 to LH 3000r Conversion Kit.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U ◊ Use HP Rack Assistant to plan the rack configuration and to check power, weight, and stability of the configured rack. Download HP Rack Assistant from: http://netserver.hp.com/netserver/support/ Anti-tip Foot Leveler Feet Figure 8-2. Anti-tip Foot and Leveler Feet l Install components such as DIMMs and processors into the system board assembly before rack-mounting the NetServer.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U • Reduced Air Flow - As you mount equipment in the rack, make sure that you allow enough air flow for safe operation of the equipment. Observe the minimum clearance dimensions listed in Appendix A, "Specifications." • Circuit Overloading - Make sure that the total configuration of equipment in the rack does not overload the supply circuit. To this end, check the nameplate ratings on all equipment.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U HP NetServer Rack Mount Parts List Make sure that the rack-mount kit that accompanies the HP NetServer contains the following parts: Table 8-1. Parts for Rack Mount Kit Quantity Description 2 Slides 8 Rack Nuts 8 Rack Nut Screws (M5 x 16mm) 6 Screws for Slides (8-32 x ¼ inch) 1 Template Rack-Mounting the HP NetServer Install the slides, which hold the HP NetServer in the rack.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U Installing Bezel Rack Nuts Facing the front of the rack: 1. Install the bezel-latch rack nuts on the right front column (holes 11 and 15 up from the baseline). 2. Install the bezel-hinge rack nuts on the left front column (holes 6 and 19 up from the baseline). Template Install the bezel latch rack nuts at the 11th and 15th holes up from the baseline (front right column). Top is 8 EIA units from the baseline.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U Installing Bar Nuts The "bar nut" is a two-hole metal bar used to secure the mounting flanges of the slide to the rack columns. All four mounting brackets on the slides attach behind the outside faces of the columns using bar nuts. Use the template (or if you no longer have it, count) and mark the twentieth and twenty-second holes up from the baseline on each column.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U The bar nut is placed behind the outside face of the column, at the height determined with the template, or by counting. 1. Insert two screws through the marked holes on the front columns. 2. Start (but do not tighten) two screws through the face of the bar nut. Install the bar nuts on all four rack columns. Place bar nut behind outside face of column. Start two screws in bar nut but do not tighten. Figure 8-6.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U Attaching the Slides The slides have mounting flanges at each end (see Figure 8-7). The mounting flange is inserted between the column and the bar nut. The slots in the mounting flange allow you to insert the flange in place behind the outside face but in front of the bar nut. The mounting flanges are then positioned behind the column face, but in front of the bar nuts.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U 1. Hold the slide so the slide members can extend out the front of the rack. 2. Insert the slide front and rear mounting flanges between the column and bar nuts. Press the slide firmly against each rack column. Insert Mounting Flange between bar nut and rear of column. Press slide tightly against column and tighten screws to hold slide in place. Figure 8-8. Securing Slide to the Rack Column 3.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U Installing the HP NetServer The following steps require lifting the HP NetServer with the mounting handles, placing it in front of the slide members, and sliding the slide members underneath the handles to secure it to the slides installed in the rack. WARNING Extend the anti-tip foot from the front of the rack and lower all leveler feet to stabilize the rack before mounting rack components.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U 3. Extend the slides until you hear a click, indicating they are locked. Note that slides do not come apart. NOTE The slide members cannot be removed. 4. Remove power supplies and hard disk drives from the server to reduce the total weight to be lifted. WARNING Two people are required to move or lift the NetServer. The HP NetServer LH 3000r weighs up to 176 pounds (80 kg.) when fully loaded. 5.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U 7. Reset the HP NetServer handles on the slides and then line up the mounting holes in the HP NetServer chassis with the screw holes in the slides (see Figure 8-11). Figure 8-11. Securing the HP NetServer to the Slides 8. Insert three screws through each slide member into the HP NetServer. Tighten all screws securely. 9. Remove the two screws from each handle and remove.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U Figure 8-12. Removing Mounting Handles Securing the HP NetServer to the Rack Complete the following steps to secure the HP NetServer to the rack and install the front bezel. 1. Attach the bezel hinge to the HP NetServer with three screws through the right edge of the bezel hinge and into the left front of the HP NetServer (see Figure 8-13). 2. Attach the bezel latch to the right side of the HP NetServer with two screws. 3.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U Lockout Latch Bezel Latch Bezel Hinge Figure 8-13. Slide Lockout Releases, Bezel Latch, and Bezel Hinge 4. Install two screws through the bezel hinge into the rack nuts on the left column. 5. Install two screws through the bezel latch into the rack nuts on the right column (see Figure 8-14).
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U Bezel Latch Bezel Hinge Figure 8-14. Securing the HP NetServer to the Rack 6. Snap the bezel on the bezel hinge and close the bezel on the bezel latch. The bezel swings open to access the HP NetServer internal mass storage cage (see Figure 8-15).
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U Figure 8-15. Installing the Bezel 7. Slide the anti-tip foot into the rack. 8. Return to the HP Rack Installation Road Map to complete the rack installation. Attaching the Cable Management Arm The Cable Management Arm for the HP NetServer LH 3000r can only be mounted on HP Systems racks.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U Rear of NetServer Left Rear Rack Column Cable Management Arm Figure 8-16. Attaching the Cable Management Arm 1. Ensure the HP NetServer is pushed all the way into the rack. 2. At the rear of the NetServer, place rack nuts on the left column in the 17th and 18th holes above the baseline of the HP NetServer. See Figure 8-16. 3. Install the two 6-32 pan head Torx 15 screws in the two threaded holes on the rear of the NetServer.
Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U Each of the HP NetServer’s two front flanges has two slots, which should line up with the rack nuts previously mounted on the rack columns. 10. Plug the HP NetServer’s power cable and all available data cables into the back of the HP NetServer. Refer to the HP NetServer LH 3000r Rack Cabling Reference Guide for information about cable dressing and routing.
9 Connecting Monitor, Keyboard, Mouse, and Power Supplies Connect the monitor, keyboard, and mouse cables to the appropriate connectors on the rear of the chassis. Serial Port Remote Management Port Parallel Port Mouse Port Keyboard Port Hot-Plug PCI LEDs LAN Port Monitor Port 1 2 3 4 Power Supplies Power Supply Status LEDs Power Connectors Figure 9-1.
Chapter 9 Connecting Monitor, Keyboard, Mouse, and Power Supplies Power Supplies You can install the third power supply in slot three or four. If you have an uninterruptible power supply (UPS), refer to the instructions supplied with it. NOTE If you have installed your HP NetServer LH 3000r into a rack, refer to the HP NetServer LH 3000r Rack Cabling Reference Guide for instructions on how to cable the NetServer to external connections.
10 Configuring the HP NetServer Introduction This chapter describes configuring the HP NetServer: l Configure mass storage as either: ◊ NetRAID (default) ◊ LVD SCSI l Updating the BIOS l Selecting a language (for example, French) l Installing the Network Operating System (NOS) NOTE The HP NetServer ships with NetRAID as the default. If you plan to configure mass storage as LVD SCSI, change the default using the Setup Utility prior to installing the NOS.
Chapter 10 Configuring the HP NetServer If the autorun feature is on, your Navigator CD-ROM program will run automatically. If the autorun feature is turned off on your computer, do this: a. Access the CD-ROM with your NOS. b. Run launch32.exe. 2. Choose the HP NetServer you are installing. 3. Choose the NOS of the server you are configuring. 4. Review "What’s New on the CD." You can save to a flexible diskette and print information for later reference.
Chapter 10 Configuring the HP NetServer • Release date • Part number of the HP Navigator CD-ROM • Document Number Status Report The Status Report for your specific Navigator CD-ROM version describes in detail any software updates between the version and the previous version. To obtain a Release History or a Status Report, go to one of these sites: • http://netserver.hp.com/netserver/ or l ftp://ftp.hp.com/pub/servers For a release history, use document number 6005.
Chapter 10 Configuring the HP NetServer Check the Readme File First This file includes the most recent information that was not included in the printed installation documentation. Follow these steps to view the file. 1. Press the power-on button. 2. Press the CD-ROM drive eject button. 3. Place the Navigator CD-ROM in the drive, and press the eject button again to close the drive. NOTE Using the low profile CD-ROM drive is slightly different than full-height units.
Chapter 10 Configuring the HP NetServer Installation Assistant HP Installation Assistant guides you through the NOS installation and configures the NOS with the appropriate drivers for the HP-bundled configuration. If Configuration Assistant detects that a newer version of the BIOS is available on the HP Navigator CD-ROM it will prompt you to update the BIOS. Configuration Assistant Configuration Assistant guides you through the steps necessary to configure the HP NetServer.
Chapter 10 Configuring the HP NetServer configure your NOS with appropriate drivers for HP-bundled configurations. This installation also loads the Local Support Tool onto Windows NT or NetWare systems. The Local Support Tool is a stand-alone support tool accessed directly from the NetServer. It gives you information to help you manage the NetServer.
Chapter 10 Configuring the HP NetServer • Show System Information: Use this screen to display information about standard and accessory boards and devices in the system, as well as the used and available system resources. ◊ Select View Hardware Inventory on the Show System Information screen to display information about standard and accessory boards and devices in the system.
Chapter 10 Configuring the HP NetServer Custom Configuration Select Custom if you are experienced in NetServer configuration and have a preferred sequence of steps, or if you prefer to configure your system one component at a time. In Custom configuration mode, you perform the same configuration steps as provided in Express configuration mode, but these can be done in any order.
Chapter 10 Configuring the HP NetServer • Show NOS Installation Instructions: Select this option to save a copy of NOS installation instructions to diskette and to print it out. Replicate Configuration In Replicate configuration mode, you can save a copy of your current system configuration or load a previously saved configuration. This method saves time when configuring multiple, identical systems. Select Replicate on the Configuration Assistant menu.
Chapter 10 Configuring the HP NetServer HP Management Solutions HP Management Solutions is a comprehensive suite of utilities, applications, and built-in features to manage multiple HP NetServers locally or from remote locations. If you are unfamiliar with these products or concepts: l To view information on HP TopTools and all HP NetServer management options for your NetServer, go to the Management Web site on the HP Web Site at http://www.hp.
Chapter 10 Configuring the HP NetServer • Easy linkage with leading management platforms including HP OpenView Network Node Manager and Workgroup Node Manager • Support for DMI 2.0, which provides the same Desktop Management Interface inventory information for NetServers as for desktop PCs Install TopTools to help your service provider troubleshoot your system. TopTools is located on HP TopTools CD-ROM included with the system.
Chapter 10 Configuring the HP NetServer PcANYWHERE32 pcANYWHERE32 is remote-control graphics-redirection software from Symantec Corporation that allows you to take control of Microsoft Windows NT Servers across the network or over a modem. Refer to the HP NetServer Online Documentation CD-ROM for details, or the HP TopTools Remote Control User Guide.
Chapter 10 Configuring the HP NetServer Setup Utility The HP NetServer has a Setup Utility (BIOS) in read-only memory. The utility features several system configuration and housekeeping options, including security, and system console characteristics. The following sections tell how to access the Setup Utility, and how to perform selected tasks. Starting the Setup Utility To reach the Setup Utility, boot or reboot the system.
Chapter 10 Configuring the HP NetServer ◊ I20 Settings – Use this menu to set the maximum number of I20 drives (4), the message timeout multiplier (1 to 1000), the pause interval during POST, or start the IRTOS (I20 Real Time Operating System) manually. ◊ Embedded LAN and SCSI Settings – Use this menu to: ∗ Change between HP NetRAID (default) and LVD SCSI modes ∗ set the Embedded NIC to enable, disable, or enable as a boot device (Boot ROM Enabled).
Chapter 10 Configuring the HP NetServer • Exit – Exit the Setup Utility by saving changes or exit without saving changes, which reverts to previous settings. When you exit, the HP NetServer reboots. Using the Setup Screens Online help explains the settings displayed on the Setup Utility screens. Instructions are also provided for navigating between the screens and entering or changing the setup data. • Press the right-arrow and left-arrow keys to move between selections on the menu bar.
Chapter 10 Configuring the HP NetServer 3. If necessary, use the up-arrow key to move to the System Time field. The "System Time" field is highlighted by default when the "Configuration" menu is selected. This field actually consists of three sub-fields, enclosed in brackets [xx:xx:xx]: hours to the left (24-hour clock), minutes in the middle, and seconds to the right. 4. Type in the hour and press Enter to move to the minutes field. 5.
Chapter 10 Configuring the HP NetServer 2. Use the right-arrow or left-arrow key to select Security from the menu bar. As soon as it is selected, the selections for the Security menu appear as shown below. Power-On Password Hardware Security The arrowhead indicates there is a submenu to select from. 3. If necessary, use the arrow key to move to the Power-On Password menu selection and press Enter. The Power-On Password is highlighted by default when the Security menu is selected.
Chapter 10 Configuring the HP NetServer 6. If necessary, enter the new password in the "Enter New Password: [ field. ]" 7. Enter the new password again in the "Re-Enter New Password: [ field. ]" After re-entering the new password a pop-up menu displays asking you to confirm your selection. NOTE To leave the pop-up menu without entering a password, press the Esc key at any time. 8. Choose Yes and then press the Enter key.
Chapter 10 Configuring the HP NetServer 16. Press Enter to toggle [Disabled] to "Enabled" in the Video Blanking [Disabled] field. Setting this feature only provides a blank screen on the HP NetServer’s Monitor, when the Keyboard Lock or Network Server Mode are also enabled. The screen remains blank until the password is typed and only applies to the monitor connected to the HP NetServer’s embedded video connection.
Chapter 10 Configuring the HP NetServer Changing Internal Device Boot Priority You can change the boot priority of the HP NetServer’s internal mass storage devices: the CD-ROM, the flexible disk drive (or other removable device), and hard drives connected to the HP NetServer’s internal SCSI ports. To do this: 1. Select "Boot Settings" from the Configuration menu, using the down-arrow or up-arrow key, and press Enter.
Chapter 10 Configuring the HP NetServer boards) installed. The system attempts to boot the NOS on the first hard disk drive (or DAC or SCSI board) found in this list. If no NOS is found, the system tries the next hard drive in the list until a NOS is found. 1. [Bootable Cards] 2. [#30 ID01 LUN0 HP 3. [#30 ID02 LUN0 HP 4.26GB A] 4.26GB A] 6. Use the plus (+) or minus (-) keys to move the desired hard drive (or DAC or SCSI board) to the top of the list.
Chapter 10 Configuring the HP NetServer Clearing CMOS The Setup Utility does not provide a method of clearing CMOS from within the Utility. To clear the CMOS of the configuration settings, you must use the configuration switch on the system board. 1. Power down the HP NetServer and gain access to the system board. Refer to Chapter 3, "Opening and Closing the HP NetServer." 2. On the system board, reset switch 5 on the configuration switch block from Off (open) to On (closed).
Chapter 10 Configuring the HP NetServer SCSI Configuration Utility NOTE The Symbios Configuration Utility is not available if you leave the NetRAID default unchanged. It is only available for LVD SCSI mode. If you need to verify or modify SCSI host adapter settings, or if you need to low-level format SCSI disks or verify SCSI disk media, run the Symbios Configuration utility: 1. Turn on or reboot your system. 2.
11 Information Assistant Introduction The HP NetServer Online Documentation CD-ROM includes "Information Assistant," which contains the entire set of documentation for your HP NetServer.
Chapter 11 Information Assistant Select a topic from the Map. Displays a window with an outline of every module and topic in Information Assistant for the selected product. The Map enables you to view the contents of the Information Assistant in outline format, and to then select a topic. Search for a word or phrase using Search. Search performs full-text searches for topic text. You can use search operators such as AND, OR, NOT, and NEAR to further narrow your search.
Chapter 11 Information Assistant You can also navigate between topics by using hot spots and by using the History button to revisit previously viewed topics. For example: • Jump to other topics. Click on hot spots in graphics and text that link to other topics or to more information about the current topic. Hot spot text appears as bold green text. Identify hot spots on graphics by moving the pointer over the graphic. When you point to a hot spot, the pointer changes to a hand.
Chapter 11 Information Assistant Installing from the CD-ROM To install Information Assistant onto a Windows PC from the HP NetServer Online Documentation CD-ROM, perform these steps: 1. Turn on your computer. 2. Insert the HP NetServer Online Documentation CD-ROM into the CD-ROM drive. 3. If you have the Autorun feature enabled, the CD-ROM starts automatically. 4. If you have Autorun disabled, at the command prompt, type the following: drive: \infoasst\setup where drive is the letter of the CD-ROM drive.
12 Troubleshooting Troubleshooting Tools If you are having problems installing your HP NetServer, a number of different tools are available for troubleshooting: • HP NetServer Information Assistant (see Chapter 11) contains the following tools: ◊ Troubleshooting Information ◊ Parts Information ◊ List of Error and Beep Error Messages WARNING Before removing the top cover, always disconnect the power cord and unplug telephone cables.
Chapter 12 Troubleshooting ◊ More NetServer Utilities>>Diskette Library: Enables you to conveniently generate a flexible diskette for any utility available on the HP NetServer Navigator CD-ROM. For example, you can create diskettes for the following utilities: BIOS Update, NOS Drivers, and DiagTools. CAUTION Replace all covers before operating the HP NetServer, even for a short time. Otherwise, overheating can damage chips, boards, and mass storage devices.
Chapter 12 Troubleshooting • Ensure the HP NetServer is configured properly. Most HP NetServer problems are the result of incorrect system and SCSI subsystem configurations. ◊ Check the Setup Utility, and the SCSI Configuration Utility. ◊ If the HP NetServer is configured with a disk array, check the disk array utility. • If the error is a network-related problem, determine if the server has enough memory and hard disk drive capacity. Consult your network operating system manual.
Chapter 12 Troubleshooting If the System Does Not Power On Follow these steps: 1. Check that all cables and power cords are firmly plugged into their proper receptacles. 2. Check that all parts of the system are turned on and properly adjusted. 3. If the server is plugged into a switched multiple-outlet box, make sure the switch on the outlet box is turned on. 4. Plug a different electrical device (such as a printer) into the power outlet, and turn it on. 5.
Chapter 12 Troubleshooting b. Check that all accessory boards are firmly seated in their slots. c. Ensure that all disk drive power and data cables are securely and properly connected. Verify the mass storage configuration with the cabling and switch diagrams. d. Verify that the DIMMs are firmly seated on the System Board. Verify that added DIMMs are HP DIMMs. e. Replace the HP NetServer covers and lock the system. f. Replace all power cords and cables. g. Turn on the monitor. h. Turn on the server. i.
Chapter 12 Troubleshooting • Display "PASSED" or "FAILED" overall results of basic tests. • Record detailed test results of basic system tests. • Display a menu of advanced tests. • Select and run one or a series of advanced tests. • Add the record of results of advanced tests to the record of basic tests. • View a list to locate the meaning of a specific error code. • View one or more steps to help confirm and isolate error conditions.
Not Used Clear Config Clear Password Troubleshooting CPU Speed CPU Speed CPU Speed Chapter 12 ON Not Used Clear Password 1 2 3 4 5 6 7 8 Clear Config CPU Speed CPU Speed CPU Speed Configuration Switch ON 1 2 3 4 5 6 7 8 Figure 12-1. System Assembly Board and System Switches 3. Move the configuration memory switch, switch 5 on the system board, to the "ON = CLEAR CONFIG" position. Refer to Figure 12-1.
Chapter 12 Troubleshooting 4. Plug in the power cord and turn on power to the HP NetServer. The following message appears: The configuration has been cleared. Set the Clear Config switch to the OFF position before rebooting. 5. Turn off power to the HP NetServer and unplug the power cord. 6. Return switch 5 on the system board to the OFF position. 7. Replace the top cover and the front bezel, then plug in the power cord. 8. Turn on power to the HP NetServer.
13 Alternative Rack Mounting Introduction This chapter provides the instructions for mounting the HP NetServer in an HP Systems rack. Bar Column Nut Inside Face Outside Face Handles NetServer Slide Bezel Latch Rack Template Leveler Feet Bezel Slide Member Anti-Tip Foot Bezel Hinge Figure 13-1. Installation Hardware If you have the newer HP System/E or System/U racks, go to Chapter 8, "Installing the HP NetServer in the HP Rack System/E or Rack System/U.
Chapter 13 Alternative Rack Mounting NOTE The pedestal HP NetServer LH 3000 cannot be rack installed without a conversion kit. Contact your HP reseller for information about the HP NetServer LH 3000 to LH 3000r Conversion Kit. Rack-mounting Guidelines and Precautions Observe the following guidelines and safety precautions during the rack-mount installation. l Extend the rack’s anti-tip foot prior to any work on the rack to prevent rack tip-over, equipment damage, and injury.
Chapter 13 Alternative Rack Mounting Always keep the following safety and environmental issues in mind, especially if you install the HP NetServer in a non-HP rack environment: • Maximum Recommended Ambient Temperature - The maximum recommended ambient temperature of the room is 35°C (95°F). • Elevated Operating Ambient Temperature - The ambient operating temperature within a closed or multi-unit rack assembly is likely to exceed the room’s ambient temperature.
Chapter 13 Alternative Rack Mounting Tools Required The following tools are required to install the NetServer: • Small adjustable open-end wrench • Torx 15 and 25 drivers • Phillips head screwdriver • Hewlett-Packard Systems Rack template • Tape or a marker pen to mark mounting locations Installing the Slides The following steps and illustrations describe how install slides for mounting a NetServer.
Chapter 13 Alternative Rack Mounting Marking Rear Columns 5. Mark the slide mounting holes on the inside faces of the rear columns. 6. Mark the baseline (bottom) of the NetServer at an EIA unit mark on the column. 7. Hold the bottom of the rack template at the baseline. Mark the top of NetServer (8 EIA units counted up from the baseline). 8. Mark the slide mounting hole (hole 21 counted up from the baseline). 9. Mark the second rear column by repeating steps 5 through 8.
Chapter 13 Alternative Rack Mounting Installing Rack Nuts Rack nuts are installed on the front columns to secure the bezel latch and hinge. Use the rack template to locate the mounting holes. 10. Install the bezel latch rack nuts on the right front column (holes 11 and 15 counted up from the baseline). 11. Install the bezel hinge rack nuts on the left front column (holes 6 and 19 counted up from the baseline).
Chapter 13 Alternative Rack Mounting Installing Bar Nuts The "bar nut" is a two-hole metal bar used to secure the mounting flanges of the slide to the front columns. Place bar nut behind outside face of column. Start two screws in bar nut but do not tighten. Figure 13-4. Installing Bar Nuts 12. Hold the bar nut behind the outside face of the front column, at the slide screw holes marked earlier. Start (but do not tighten) two screws through the face of the into the bar nut. 13.
Chapter 13 Alternative Rack Mounting Attaching the Slides The following steps describe how to attach the slides to the columns. 14. Remove the removable mounting flange. A large, flat-blade screwdriver inserted between the flange and the slide from the end of the slide may help in removal. This mounting flange is not required when installing a slide in an HP systems rack. 15. Remove hex nuts and lock washers securing the removable mounting flange to the slide. Save the hex nuts and lock washers. 16.
Chapter 13 Alternative Rack Mounting 17. Insert the slide fixed mounting flange between the column and bar nuts. Press the slide firmly against the front column (see Figure 13-6). 1. Insert mounting flange of slides between bar nut and rear side of column face. 2. Press slide tightly against column and tighten screws to hold slide in place. Figure 13-6. Securing the Slide to the Front Column NOTE The slide members cannot be removed. 18. Tighten both screws in the mounting flanges of the slide. 19.
Chapter 13 Alternative Rack Mounting Completing the NetServer Installation Installing the HP NetServer on the slides, securing it to the rack, and installing the cable management arm completes the installation of the NetServer in the HP Systems rack. Follow the steps beginning in the section "Installing the HP NetServer" in Chapter 8 to complete the installation.
A Specifications The specifications listed below vary if you install a mass storage device in your server that has more stringent environmental limits. Make sure that the operating environment for your server is suitable for all the mass storage devices that you are using.
Appendix A Specifications Weight and Dimensions NOTE Use one person for every 40 pounds of NetServer weight when lifting it. LH 3000r LH 3000 Height 354.7 mm (14 in) 494.8 mm (19.5 in) Width 482.6 mm (19 in) 350.5 mm (13.8 in) Depth 749.2 mm (29.5 in) 724.2 mm (28.5 in) 35 - 50 kg (77 - 110 lbs.) 35 - 50 kg (77 - 110 lbs.) Weight Empty Power Requirements Power Supply Specifications: Power supply type Auto-Ranging Input voltages: Nominal: 100 to 127 VAC ~ 8.3 A at 50Hz 200 to 240 VAC ~ 3.
Appendix A Specifications Video The video memory used for the HP LH 3000 or HP LH 3000r NetServer is a 16Mbit (2MB) SGRAM, with architecture of 256K x 32 bit x 2 banks. 2D Video Modes The LH 3000 supports these 2D video configurations: Resolution 256 Colors 65K Colors 16.
B Regulatory Information Regulatory Notices - Electromagnetic Compliance Electromagnetic Compatibility (EMC) requirements have been established in many countries to regulate the radio frequency energy generated by Information Technology Equipment (ITE). This energy is generated during the normal and intended use of this equipment and so it is limited by country regulations to levels intended to minimize potential interference to other electrical equipment, including public safety services.
Appendix B Regulatory Information • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/television technician for help. Hewlett-Packard’s system certification tests were conducted with HP-supported peripheral devices and HP shielded cables, such as those you receive with your computer.
Appendix B Regulatory Information Notice for Japan The configuration of the NetServer you have purchased may be in either the class A or class B category. For products labeled as Class B: This equipment is in the Class B category information technology equipment based on the rules of Voluntary Control Council For Interference by Information Technology Equipment (VCCI). Although aimed for residential area operation, radio interference may be caused when used near a radio or TV receiver.
Appendix B Regulatory Information Notice for Korea The configuration of the NetServer you have purchased may be in either the class A or class B category. Class A Equipment: Please note that this equipment has been approved for business purposes with regards to electromagnetic interference, if purchased in error for use in residential area, you may wish to exchange the equipment where you purchased it.
Appendix B Regulatory Information Notice for Taiwan Class A Warning Statement Notice for European Union For Class A Products WARNING Class A Products: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Radio Frequency Emissions Warning for Accessories This product has been found to comply with CISPR 22 Class B EMC emission limits.
Appendix B Regulatory Information Declaration of Conformity (US, EU, Australia) DECLARATION OF CONFORMITY According to ISO/IEC Guide 22 and EN 45014 Manufacturer’s/Supplier Name: Hewlett-Packard Company Manufacturer’s/Supplier Address: 10955 Tantau Avenue Cupertino, CA 95015 USA Declares, that the product Product Name: Model Number(s): Product Options: Network Server HP NetServer LH 3000/LH 3000r ALL Conforms to the following Product Specifications: Safety: IEC 950: 1991+A1, A2, A3, A4 / EN 60950:
Appendix B Regulatory Information Regulatory Notices - Product Safety The following information applies only to servers with factory-installed components. CD-ROM and Laser Safety Statements The following information applies only to servers with factory-installed drives. CD-ROM Electrical Safety Statement – United States WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Appendix B Regulatory Information LASER Safety - Finland LASERTURVALLISUUS LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT HP NetServer LH 3000r/LH 3000 - verkkopalvelimeen voidaan asentaa lisävarusteena laitteensisainen CD-ROM-lukulaite, joka on laserlaite. Kyseinen CD-ROM-lukulaite on käyttäjän kannalta turvallinen luokan 1 laserlaite. Normaalissa käytössä lukulaitteen suojakotelo estää laseräteen pääsyn laiteen ulkopuolelle. Laitteen turvallisuusluokka omn määritetty standardin EN 60825 (1991) mukaisesti.
Appendix B Regulatory Information CLASS 1 LASER PRODUCT This CD-ROM Drive Unit is classified as a CLASS 1 LASER PRODUCT. LASSER KLASSE 1 PRODUKT The CLASS 1 LASER PRODUCT label is located on the top of the drive. Bei diesem CD-ROM-Laufwerk CDU56S handelt es sich um ein Laser-Produkt der Klasse 1. Ein entsprechender Aufkelber mit der Beschriftung LASER KLASSE 1 PRODUKT befindet sich der Obersiete des Geräts. Battery Statements This product uses a lithium battery.
Appendix B Regulatory Information Noise and Ergonomic Safety Statements Noise Declaration and Ergonomics - Germany Sound Pressure: LpA < 58 dB (A) am Arbetsplatz, Beobachter Position (workplace, bystander position) normaler Betrieb (normal operation) nach DIN 45635 T. 19 (per ISO 7779) This product has not been evaluated for compliance with the ZH1/618/ISO 9241 ergonomic requirements.
C Service and Support For all Service and Support information, see the HP NetServer Warranty and Service/Support Booklet included with your product.
D Warranty and Software License Warranty See the HP NetServer Warranty and Service/Support Booklet included with your product for all warranty and service/support information. HP Software Product License Agreement ATTENTION: USE OF THE SOFTWARE IS SUBJECT TO THE HP SOFTWARE LICENSE TERMS SET FORTH BELOW. USING THE SOFTWARE INDICATES YOUR ACCEPTANCE OF THESE LICENSE TERMS. IF YOU DO NOT ACCEPT THESE LICENSE TERMS, YOU MAY RETURN THE SOFTWARE FOR A FULL REFUND.
Appendix D Warranty and Software License If your Computer was shipped with a Recovery CD, (i) the Recovery CD and/or Support Utility software may be used only for restoring the hard disk of the HP computer system with which the Recovery CD originally was provided, and (ii) if separate EULA(s) are included with your Computer for any other Microsoft products which are included on the Recovery CD, those Microsoft products are subject to the terms of their respective EULA(s). No Disassembly or Decryption.
Index 2 2D display modes, 155 3 3D Display Modes, 155 B BIOS update, 111 Boot device priority changing boot priority for internal mass storage, 126 remove built-in SCSI channels from boot order, 129 Boot password setting, 122 C CAUTION NetServer covers are heavy, 36 Change flexible disk type, 120 Changes system date:, 121 time:, 121 CMOS clearing, 128 Configuration custom, 114 Express, 111 Replicate, 115 Configuration Advisories, 112 Configuration Assistant express configuration, 111 connecting to AC power
Index Front Panel Console display navigation buttons, 14 H handles removing after mounting, 97 hard disk drive Symbios Configuration formatting, 110 Hard disk drive hot-swap formatting, 110 NetRAID, 52 hardware support, 167 Hot add PCI board, 68 hot swap hard disk drive installing, 46 removing, 49 Hot swap hard disk drive changing boot priority for internal mass storage, 126 removing internal drives from boot order, 129 Hot-Plug Utility, 69 Hot-swap hard disk drive NetRAID, 52 HP Management Solutions, 116
Index PCI boards installing, 59 Power button protective cover, 14 Power Switch, 12 Power-on Tests, 25 Precautions, 135 problem notification TopTools, 116 Processor steppings, 72 Product Safety, 163 R Rack removing LH 3000r from the rack, 33 rack mount kit parts list, 89 rack, installing HP NetServer in, 88 rack, installing NetServer in alternative, 143 RAID, 52 Readme file, 110 Regulatory Notices - Electromagnetic Compliance, 157 Regulatory Notices - Product Safety, 163 Remote control, 118 removing a drive
Index U Utilities BIOS Update, 118 Configuration Assistant utilities, 111 DiagTools, 118 event log report, 118 hard drive formatting, 110 HP NetServer Assistant, 118 Information Assistant, 131 Navigator CD-ROM utilities, 118 on Navigator CD-ROM, 135 PowerWise Assistant, 118 SCSI configuration utility, 129 Setup, 110 Setup Utility, 119 174 Symbios Configuration, 110 Utility partition, installation, 114 V video memory, 155 video resolution, 155 VRM installation, 77, 83 W WARNING Lift HP NetServer with two
