Specifications
Mechanical Drawings
62 Thermal/Mechanical Design Guide
Figure B-11. Reference Clip - Sheet 1 of 2
8 7 6 5 4 3 2
H
G
F
E
D
C
B
A
8 7 6 5 4 3 2 1
H
G
F
E
D
C
B
A
A
A
THIS DRAWING CONTAINS INTEL CORPORATION CONFIDENTIAL INFORMATION. IT IS DISCLOSED IN CONFIDENCE AND ITS CONTENTS
MAY NOT BE DISCLOSED, REPRODUCED, DISPLAYED OR MODIFIED, WITHOUT THE PRIOR WRITTEN CONSENT OF INTEL CORPORATION.
REVISION HISTORY
ZONE REV DESCRIPTION DATE APPROVED
-
01
PRODUCTION RELEASE 3/27/08
C KOEPSELL
D94152 1 01
DWG. NO SHT. REV
DEPARTMENT
R
CORP.
2200 MISSION COLLEGE BLVD.
P.O. BOX 58119
SANTA CLARA, CA 95052-8119
TITLE
RCBF5 HS CLIP, 35mm core
SIZE DRAWING NUMBER REV
A1 D94152 01
SCALE: NONE DO NOT SCALE DRAWING
SHEET
1
OF
2
SEE NOTESSEE NOTES
FINISHMATERIAL
03/19/07P.JOHNSON
DATEAPPROVED BY
03/16/07K.KOZYRA
03/16/07C. KOEPSELL
DATECHECKED BY
03/15/07M. BRAZEL
DATEDRAWN BY
03/15/07M. BRAZEL
DATEDESIGNED BY
UNLESS OTHERWISE SPECIFIED
INTERPRET DIMENSIONS AND TOLERANCES
IN ACCORDANCE WITH ASME Y14.5M-1994
DIMENSIONS ARE IN MILLIMETERS
ALL UNTOLERANCED LINEAR
DIMENSIONS ±0.1
ANGLES ±0.5
THIRD ANGLE PROJECTION
PARTS LIST
DESCRIPTIONPART NUMBERITEM NOQTY
CLIP, STEEL, STAMPEDD94152-002TOP
0.5 [.019] A B
0.5 [.019] A B
D
D
SQ 53.5 0.2
2.11 .00[]
4X 10 0.2
.394 .007[]
105.94
4.171[]
105.94
4.171[]
2 0.2
.079 .007[]
3.34 0.2
.132 .007[]
45.19
1.779[]
B
736.44 0.2
1.435
.007[]
A
7
7
NOTES:
1. THIS DRAWING TO BE USED IN CONJUNCTION WITH SUPPLIED 3D
DATABASE FILE. ALL DIMENSIONS AND TOLERANCES ON THIS
DRAWING TAKE PRECEDENCE OVER SUPPLIED FILE AND ARE
APPLICABLE AT PART FREE, UNCONSTRAINED STATE UNLESS
INDICATED OTHERWISE.
2. MATERIAL:
A) TYPE: AISI 1065 COLD DRAWN STEEL OR EQUIVALENT
1.6MM THICKNESS .02 [.063"]
B) CRITICAL MECHANICAL MATERIAL PROPERTIES
FOR EQUIVALENT MATERIAL SELECTION:
ELASTIC MODULUS > 206.8 GPA [29,900 KSI]
MIN TENSILE YIELD STRENGTH (ASTM D638) > 385 MPa [71KSI]
C) MASS - 38.6 GRAMS (REF)
3. SECONDARY OPERATIONS:
A) FINISH: NICKEL PLATE REQUIRED AFTER FORMING
4. ALL DIMENSIONS AND TOLERANCES ARE SHOWN AFTER PLATING
5 PUNCH DIRECTION
6. BREAK ALL SHARP CORNERS AND BURRS
7 CRITICAL TO FUNCTION DIMENSION
8 COINING REQUIRED AS SPECIFIED
9. SECONDARY UNIT TOLERANCES SHOULD BE CALCULATED FROM PRIMARY
UNITS TO AVOID ROUND OFF ERROR.
5
7
PERMANENTLY MARK PART
NUMBER AND REVISION LEVEL
APPROXIMATELY WHERE SHOWN
XXXXXX-XXX REV XX
REMOVE ALL BURRS OR SHARP EDGES AROUND
PERIMETER OF PART. SHARPNESS OF THE EDGES SUBJECT
TO HANDLING ARE REQUIRED TO MEET THE UL1439 TEST.
SEE DETAIL A
SECTION A-A
SEE DETAIL B
SEE DETAIL C
SEE DETAIL A
SEE DETAIL B
SEE DETAIL C