OSM Service Connection User's Guide HP Part Number: 527274-044 Published: February 2014 Edition: J06.03 and subsequent J-series RVUs and H06.03 and subsequent H-series RVUs.
© Copyright 2014 Hewlett-Packard Development Company, L.P. Legal Notice Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor’s standard commercial license. The information contained herein is subject to change without notice.
Table of Contents What's New in This Guide...........................................................................33 About This Guide........................................................................................41 Related Reading..........................................................................................43 1 Introducing OSM......................................................................................45 OSM Interfaces.........................................................
Summary Menu.................................................................................................................59 Tools Menu.......................................................................................................................60 Windows Menu.................................................................................................................60 Help Menu...................................................................................................................
Using the Physical Configuration Tool........................................................................................79 9 Viewing Summary Reports.........................................................................81 Viewing a Problem Summary...................................................................................................81 Viewing a Summary of Actions.................................................................................................81 Actions Not Displayed......
Battery..................................................................................................................................91 Attributes..........................................................................................................................91 Battery.........................................................................................................................91 Physical..................................................................................................
PAL/SAL Firmware.......................................................................................................101 Actions...........................................................................................................................101 Blade System Board..............................................................................................................101 Attributes.................................................................................................................
CLIMs.................................................................................................................................108 Attributes........................................................................................................................108 Actions...........................................................................................................................109 Collect CLIM Logs ........................................................................................
Attributes........................................................................................................................117 Disk..........................................................................................................................117 Logical......................................................................................................................117 Backup Path............................................................................................................
Responsive Test...........................................................................................................123 Save as System Load Configuration...............................................................................123 Spin Down.................................................................................................................124 Spin Up.....................................................................................................................
Attributes........................................................................................................................129 Enclosure...................................................................................................................129 Physical.....................................................................................................................129 Physical Location........................................................................................................
Abort Backup Path.......................................................................................................136 Abort Disk..................................................................................................................136 Abort Primary Path......................................................................................................136 BLINK LED Off............................................................................................................
Physical.....................................................................................................................141 Logical......................................................................................................................141 Actions...........................................................................................................................141 Replace.................................................................................................................
FCDM Collection........................................................................................................147 Path B........................................................................................................................147 Path A.......................................................................................................................147 Actions...........................................................................................................................
Attributes........................................................................................................................155 G4SA........................................................................................................................155 Physical.....................................................................................................................155 Logical..................................................................................................................
Rediscover.................................................................................................................162 Hard Disk (CLIM)..................................................................................................................162 Attributes........................................................................................................................163 Hard Disk............................................................................................................
Prepare to Power Off...................................................................................................169 Replace.....................................................................................................................169 Storage ASIC Initialization Test......................................................................................170 Test Verify..................................................................................................................170 LIF.......
Actions...........................................................................................................................177 Rediscover.................................................................................................................177 Redundant Power Scrub...............................................................................................177 Set Physical Location........................................................................................................
Configure LIF..............................................................................................................184 Start..........................................................................................................................184 Stop..........................................................................................................................184 PMCU........................................................................................................................
Configuration.............................................................................................................194 Actions...........................................................................................................................194 Configure Power Source as AC.....................................................................................194 Configure Power Source as UPS....................................................................................
Enable PE Reintegration...............................................................................................201 Enable Serial ZX1 I/O Link..........................................................................................201 Power Down LSU.........................................................................................................201 Reintegrate PE............................................................................................................201 Replace LSU..........
Firmware Update........................................................................................................209 Replace.....................................................................................................................209 Set LED State..............................................................................................................209 SAS Disk Enclosures..............................................................................................................
Attributes........................................................................................................................215 ServerNet Switch Board...............................................................................................215 Physical.....................................................................................................................216 Logical......................................................................................................................
Process Pair................................................................................................................223 SCSI Interface.............................................................................................................223 Actions...........................................................................................................................223 Responsive Test...........................................................................................................
External Loopback Test.................................................................................................230 Start DLC Task............................................................................................................230 Stop DLC Task............................................................................................................230 SWAN Path.........................................................................................................................
Update Running Core License.......................................................................................238 Verify Power Fail Configuration.....................................................................................238 Related System and Processor-Level Recovery Actions............................................................239 Tape Collection....................................................................................................................239 Attributes..............
Responsive Test...........................................................................................................246 Test Verify..................................................................................................................246 VIO G4SA...........................................................................................................................247 Attributes................................................................................................................
Service State...................................................................................................................257 Tape Types......................................................................................................................258 Topology........................................................................................................................259 12 Managing a ServerNet Cluster...............................................................
ServerNet Path Test on Y Fabric.....................................................................................272 Set ServerNet Cluster State...........................................................................................272 External ServerNet Fabric......................................................................................................272 Attributes........................................................................................................................
Logical......................................................................................................................279 Firmware....................................................................................................................279 Configuration.............................................................................................................280 Actions..........................................................................................................................
Physical.....................................................................................................................286 Logical......................................................................................................................286 Actions...........................................................................................................................286 Blink LED Off...........................................................................................................
Updating to the Tri-Star Topology.......................................................................................298 Cable Connections in a Layered Topology...............................................................................298 Connections Between Layers Within a Switch Group.............................................................298 X Fabric Connections Between Two Zones...........................................................................
What's New in This Guide This version of the OSM Service Connection (T0682 H02 ADH), released in conjunction with the H06.28/J06.17 RVUs, adds: • • Support for HP Integrity NonStop NS2300 servers and NS2400 series servers, including new Processor Type values of NSE-AG for NS2300 and NSE-AH for NS2400 series. Removed all occurrences of the Enable Memory Snapshot action, as it is not valid for H- and J-series systems. Recent OSM History At H06.27/J06.
• • • The OSM Event Viewer now allows you view events time-stamped in the same time zone as the system on which they were logged. For more information, see the OSM Event Viewer online help. The Register CLIMs with Key Managers Guided Procedure now supports 2048 bit certificates. Apache OpenOffice can be installed on NonStop system consoles as part of the OSM Console Tools product on NSC Installer DVD, Update 19 or later.
• • Collect CLIM Logs action has been added to the CLIM object (was previously on just the CLIMs object). A new Prepare for Down System CLIM Firmware Update action on the CLIMs object, to be used in conjunction with the Down System CLIM Firmware Update Tool, a new component of OSM Console Tools T0634 G06 ABB and later. OSM Console Tools T0634 G06 ABB and later also includes the NonStop Maintenance LAN DHCP DNS Configuration Wizard, which replaces the CLIM Boot Service Configuration Wizard.
At H06.21/J06.10, OSM Service Connection (T0682 H02 ACE) added support for: • G6 CLIMs, including the display of two new subcomponent objects in the OSM Service Connection, Motherboard and Smart Array Controller, as well as some changes to these existing CLIM subcomponents: — DIMM — Hard Disk — PCI Riser — SAS Card • You can now specify an optional process priority for the Validate Checksum and Clear Data actions that are available under supported disk types.
• • See the OSMINIO file for examples, and the OSM Configuration Guide for more information on creating or editing a customized OSMCONF file. The Verify Power Fail Configuration action on the System object now checks the validity of these two variables. Onboard Administrator firmware version is now displayed for NonStop BladeSystem Enclosures as Bay 1 and Bay 2 OA Firmware Version attributes, located under Logical attributes.
At H06.14/J06.03, the OSM Service Connection (T0682 H02 ABI) added support for J-series in addition to H-series RVUs. This version of the OSM Service Connection User's Guide was updated to include support for J06.
At H06.07, the OSM Service Connection Suite was updated to T0682 H02 AAU to provide support for: • • • An improved module-level Redundant Power Scrub test. (Click the link or see softdoc for details.) RoHS-compliant hardware. Monitoring four Blade Element fans for Integrity NonStop NS1000 servers, five Blade Element fans for Integrity NonStop NS5000T and NS5000CG servers. Also new for H06.07 is the OSM System Inventory Tool.
About This Guide The OSM Service Connection User's Guide is available as online help within the OSM Service Connection, and in the NonStop Technical Library. From within the OSM Service Connection, you can: • Access a JavaHelp online help interface to the OSM Service Connection User's Guide by selecting Help > Help Contents from the OSM menu bar.
Related Reading Sources of OSM-related information: • • • • • • • • • This manual, the OSM Service Connection User's Guide, is available in the NonStop Technical Library (NTL) and as online help from within the OSM Service Connection. It deals mostly with using the OSM Service Connection to monitor and perform actions on system and cluster resources.
1 Introducing OSM The OSM client components are installed on a PC workstation that serves as the system console. The OSM server components are installed on the NonStop server running the HP NonStop operating system. Server-Based Components OSM server-based components (including the OSM Service Connection and OSM Event Viewer applications) have been combined into a single product, T0682. For information on how to configure and start OSM server-based processes, see the OSM Configuration Guide.
Starting the OSM Notification Director If It Is Not Running: On the main Windows task bar, click Start and then select Programs > HP OSM > OSM Notification Director > Start.
OSM Guided Procedure OSM Action For Object Replace Blade Element component Replace NonStop Blade Element or subcomponent(processor board, front panel display, memory board, reintegration board, fan, optics adapter, and I/O interface board) Replace LSU Replace LSU (located under Processor LSU or subcomponent Components object) Blade Complex Firmware Update Firmware Update Firmware running on each Blade Element in the Blade Complex * NonStop NS-series only – should be performed only by a trained se
2 Preparing the OSM Environment To plan your network LAN configuration and connect your system console so it can communicate with your NonStop server through OSM client/server software, see the NonStop NS-Series Hardware Installation Manual (shipped with every new system; also available in the Hardware Service and Maintenance collection of NTL). The OSM Configuration Guide describes how to configure and start OSM server-side processes.
3 Configuring OSM Before using OSM applications to manage your system. • • • • Configure the server using the OSM Low-Level Link (see Configuring the Server). If using HP Insight Remote Support Advanced for remote support services, see Insight Remote Support Advanced for NonStop, located in the external NonStop Service Information collection of NTL.
Defining Users To use the OSM client and server software, you must define the users that have access to your server. OSM allows two types of users: MSP (Low-Level-Link) Users • • • Can log on to the OSM Low-Level Link and connect to the MSP or ME, allowing them to access a server even when the NonStop operating system is not running. Have full privileges and can perform serious actions such as loading the processor or starting the system.
Dial-out/Dial-in You can configure the OSM client software to notify a remote service provider of problems with your server. This remote notification is referred to as dial-out. Problems are reported to the OSM Notification Director in the form of problem incident reports, which can be forwarded to or automatically dialed out to a remote service provider.
4 Starting the OSM Service Connection You • • • • • can: Launch an OSM Service Connection OSM Service Connection Session Error Messages Using OSM Bookmarks Verify the OSM Service Connection State Run Multiple Sessions Launching an OSM Service Connection 1. To initiate an OSM Service Connection session, either: • Open a new Internet Explorer browser window (but not from within a current browser window).
OSM Service Connection Session Error Messages Server Undiscovered An OSM Service Connection session cannot be established until system discovery is complete. Close the browser session that generated the "Server Undiscovered" message, wait until discovery is complete and then establish a new OSM Service Connection session. Server Down An OSM Service Connection session cannot be established.
5 Using the Management Window The OSM Management window appears after system discovery. It displays OSM features and information about your local system and ServerNet cluster. The Management window contains an OSM menu bar and these panes: Overview Displays a high-level view of system objects, such as internal fabrics, groups, and external devices (external disks and tapes), and of ServerNet Cluster objects, such as external fabrics, local nodes, and remote nodes.
Management Window Example Internet Explorer Menu Bar The Internet Explorer menu bar is not customized for the OSM application. For most OSM functions, use the OSM menu bar (located above the view pane) and the various panes within the Management window. Internet Explorer functions that you might use for OSM include • • • Access OSM bookmarks from the Internet Explorer Favorites menu. However, you must use the OSM Create Bookmark function in the Tools menu to create the bookmarks.
to a menu option under the Tools menu. This topic describes the options available under each OSM menu. CAUTION: Do not close the Management window when any OSM dialog box is open. You will lose your current service connection. Display Menu The Display menu contains the following items: Attributes Displays the Attributes dialog box for the selected object. See Using the Attributes Dialog Box to View Attributes.
Tools Menu The Tools menu contains the following items: Logical Status Displays the Multi-Resource Action dialog box, pre-configured with a default logical view of your system designed to give you a method for monitoring the health of key system components. This view provides status for all logical processors, disks, LIFs, and SWAN paths.
Help Menu The Help menu contains: Help Contents Displays a JavaHelp online help interface to the OSM Service Connection User's Guide. You can also access context-sensitive help topics (from this same JavaHelp interface) directly from the OSM GUI by selecting objects in the GUI and pressing the F1 key, or by clicking Help buttons where provided within GUI dialog boxes. About OSM Opens the About dialog box containing OSM product information, such as version number and trademarks.
1. 2. In the tree or Overview pane, select the system name. From the View list, select Physical. Physical View of an Enclosure The Physical view of a group enclosure is similar to the way the group looks with the enclosure door open. This view shows both the appearance side and the service side of a group. The appearance side is the front view, which you see when you open the door of the enclosure. The service side is the back view.
The Inventory view of a ServerNet cluster displays: Name The logical name of a component in the cluster and the switch zone and fabric in which it is located. For example: Switch Group 1020 (the switch group in zone 2 on the X fabric) Serial Number A unique identification number assigned to a external switch port. Type The type of switch plug-in card (such as Router Interconnect) or transceiver (such as 9/125 Micron SMF). Power State Indication of whether the component is powered on or off.
The shortcut menu for all resources contains these choices: Attributes brings up the Attributes dialog box for that resource. Alarms brings up the Alarms dialog box for that resource. The Alarm menu item is unavailable if there are no alarms on the resource. Actions brings up the Action dialog box for that resource. All system resources also contain this choice: Rediscover causes OSM to refresh and reanalyze the object and all subcomponents.
In the tree pane, a yellow icon displayed over a system, group, module, or any parent object that contains subcomponents indicates that one or more subcomponents require service or operational intervention. State icons are also shown in the Physical view of a cluster or system.
Alarm Severity Critical Immediate corrective action is required. A service-affecting fault occurred. For example, a resource might have become unavailable. Major Urgent corrective action is required. A service-affecting fault has developed. For example, a resource might have lost fault tolerance. Minor A fault exists that does not affect service. Corrective action should be taken to prevent a more serious fault. For example, an unexpected path change occurred.
6 Viewing Alarms When certain problem conditions exist on a system, OSM generates alarms on the objects in need of service or attention. Alarms can be viewed in these ways: • Alarms associated with a specific resource: — Right-click the object and select Alarms to display the Alarms dialog box. — Click the Alarms Tab of the Details pane to view alarms for the selected object. • A summary of alarms for the entire server or ServerNet cluster; see Viewing a Summary of Alarms.
or act on those alarms. To view a summary of alarms for the entire system, see Viewing a Summary of Alarms. The Alarms dialog box provides this information about the selected alarm: • Alarm severity The Severity column contains a colored icon corresponding to the severity of the alarm. Red icons represent Critical and Major alarms. Yellow icons represent Minor, Warning, and Indeterminate alarms. See Alarm Severity.
Select, then right-click an alarm in the Alarms tab, Alarms dialog box, or the Alarm Summary dialog box and click either Permanent or Temporary suppression, as desired: • • If you select Permanent suppression and the same alarm is generated again on this object at a later time, state propagation will not occur. If you select Temporary suppression and the same alarm is generated again on this object at a later time, state propagation will occur.
7 Viewing Attributes Every resource has attributes associated with it. You can view the attributes of a resource in the details pane of the Management window, or you can display the Attributes dialog box, which is available from any view. To view attributes for a selected resource without opening the Attributes dialog box, see Using the Details Pane to View Attributes. For further information on viewing the Attributes dialog box, see Using the Attributes Dialog Box to View Attributes.
Select, then right-click a problem attribute in either the Attributes tab or Attributes dialog box and click either Permanent or Temporary suppression, as desired:. • • If you select Permanent suppression and the same attribute value is generated again on this object at a later time, state propagation will not occur. If you select Temporary suppression and the same attribute value is generated again on this object at a later time, state propagation will occur.
8 Performing Actions You can perform and monitor actions as follows: • • • • • • Perform a specific action on a selected resource: Performing Actions on a Selected Resource. Perform a specific action on several resources of the same type: Performing Actions on Multiple Resources of the Same Type. Perform a firmware update on a specific resource: Performing Firmware Updates. View a summary of actions in progress and recently completed: Viewing a Summary of Actions.
Behavior for the three Default Roles is as follows: • • NonStop Super ID – No changes can be made to this default role, in terms of membership or privileges, nor can this role be deleted. For the default roles Everyone and NonStop Super Group Users, cannot add or delete members, but you can change the privileges assigned to those roles. You can delete a selected role using the Delete Role button or restore them if they have been deleted by using the Restore Default Roles button.
in this dialog box. You can add members to the new role by clicking Add Member. Under Privileges, select the actions that can be performed by the members of this role. Any OSM actions not listed here are actions that cannot be restricted through the Access Control List functionality. Click Save Role to save the role and have it added to the list of available roles. You can delete members from a role by using the Delete Member button or delete a selected role by clicking Delete Role.
Viewing Detailed Information About an Action 1. 2. In the Action Status list, select the action whose details you want to view. Click Details to display the Action Detail dialog box. The Action Detail dialog box provides a description of the action, the resource acted on, and the action status. The detail also includes the cause, effect, and repair action for any failed action.
4. 5. Select the specific resources on which to perform the action: Select To Add all Move all resources in the available resources list to the selected resources list. (The Add all button is enabled only when no resource in the available resource list is highlighted.) Add Move a specific resource (selected by clicking it) from the available list to the selected list. Remove all Move all resources from the selected list back to the available list.
Deleting a Resource View 1. 2. 3. In the Multi-Resource Actions dialog box, click Configure…. In the Multi-Resource Configuration dialog box, select the name of the resource view you want to delete from the drop-down menu. Click Delete. Viewing Action Details The Action Detail box provides a description of a selected action, the resource acted upon, and the action status. The detail also includes the cause, effect, and repair action for any failed action.
5. 6. Select the specific resources on which to perform the action: Select To Add all Move all resources in the available resources list to the selected resources list. (The Add all button is enabled only when no resource in the available resource list is highlighted.) Add Move a specific resource (selected by clicking it) from the available list to the selected list. Remove all Move all resources from the selected list back to the available list.
Now you do not need to use the Set Physical Location* action to specify Rack Name or Rack Offset. Instead, you can use the Physical Configuration Tool to: • • • Drag and drop components between and within the panes to accurately depict your actual physical configuration. Click Add Rack to add new racks to the Configured Racks pane. Save the physical view to an HTML file for use outside of OSM.
9 Viewing Summary Reports You • • • • can view a: Problem Summary Summary of Actions Summary of Alarms Resource Summary Viewing a Problem Summary The Problem Summary lists all resources that are in a problem state. The report lists this information: • • • • The The The The name of the problem resource Service State (See possible values.) attribute group in which the problem occurs attributes in which the problem occurs To create the report: Select Summary > Problem.
The Alarm Summary dialog box provides this information about each alarm: • • • • • • Alarm severity Time and date the alarm occurred Resource name Description of the alarm, including probable cause and alarm type Whether or not the alarm is suppressed Whether the alarm is dialed out to your service provider (assuming your system console is configured to dial out) To display detailed information for an alarm: Highlight the alarm and click Detail.
10 Managing a System A system consists of all the hardware components, software, and firmware that are managed by a single operating system. Using the OSM applications, you can monitor and maintain your local server to check the status of all system components and to watch for indications of potential system problems. You can also perform OSM actions to resolve many system problems. For details about the resources that make up a system, see System Resources. Locating and Viewing System Resources 1. 2.
11 System Resources Using OSM, you can monitor and maintain these system resources: Alarm Panel FESA Processor Blade 4PSE Fiber (Blade Switch Port) Processor Components ATM Adapter Fibre Channel Router Processor Switch Module ATM Line FSAC SAC Battery G4SA SAS Card (CLIM) Blade Complex G4SA PIF SAS Disk Enclosure Blade Element G4SA SAC SAS Disk Enclosures Blade Element Firmware GESA SCSI Controller Blade System Board Group (IOAM, Fabric, or G16SE) ServerNet Interface Card (Blade)
FC Card (CLIM) Power Supply (IOAM) VIO FCSA FC-AL I/O Module Power Supply (Processor Switch) VIO G4SA FCDM Power Supply (SAS Disk Enclosure) VIO Logic Board FCDM Collection Power Supply and Fan (Telco SAS Disk VIO Module Enclosure) FCSA Power Supply (VIO) FCSA FSAC Processor (CLIM) 4PSE (4-Port ServerNet Extender) Used only in HP Integrity NonStop NS14000 or NonStop NS1000 systems containing IOAMs, 4PSEs provide ServerNet connectivity to the processors.
Set LED State Turns on or off the amber LED located on the 4PSE. The current state is indicated by the LED State attribute. Alarm Panel (Telco) For Telco systems only, this object can be displayed and monitored in OSM by using the Start Monitoring Alarm Panel action, located under the Monitored Service LAN Devices object. You can access its browser-based configuration interface through the Link to Web Interface action.
Actions Link to Web Interface Opens a Web interface that provides detailed device configuration and information for the alarm panel. Rediscover Causes OSM to refresh and reanalyze the object. Refresh refers to OSM updating the attribute values displayed in the OSM Service Connection interface. Reanalyze refers to the running of OSM incident analysis, which checks EMS event messages and creates alarms in OSM if certain conditions exist. Stop Monitoring Stops OSM from monitoring the alarm panel.
Automatic Dump State Indication of whether the ATM adapter software is automatically dumped to the specified dump file if the software abends abnormally. Enabled: The software is automatically copied. Disabled: The software is not automatically copied. Unknown:: The Automatic Dump state could not be read. Media Type The type of media or cable, such as single-mode fiber or coaxial cable, supported by the ATM CRU.
Test Verify Runs all the firmware diagnostic tests on the CRU. This test takes about three minutes to finish. The CRU must be in the Stopped state before you initiate the Test Verify action. ATM Line The Asynchronous Transfer Mode (ATM) line represents the logical link between the ATM CRU and the ATM network. There is one ATM line per ATM CRU. This Nonstop S-series component can be connected to a Nonstop NS-series system through an IOMF2 enclosure.
Battery The battery customer-replaceable unit (CRU), located in Nonstop S-series processor or I/O enclosures, is an assembly of 24 cells rated at 2.5 amp-hours per cell. The batteries are designed to handle occasional power failures that might occur at typical computer sites. Each processor or I/O enclosure contains two batteries. Location in OSM Tree: System > Group > Module > Battery Slot Location: In processor enclosures, battery CRUs are located in slots 23 and 28 (appearance side). Example: Battery (1.
Total Voltage Sensor Normal Minimum Value The minimum voltage that the battery should maintain is 42 volts. If the battery's Total Voltage falls below 42 volts, an alarm is generated. (If the Total Voltage falls below the Disconnect Voltage Limit of 39.6 volts, the battery is disconnected.) Lower Fatal Threshold The minimum voltage that the battery must maintain to continue operating is 39.6 volts. If the battery's Total Voltage falls below 39.6, the battery is disconnected.
Logical Activity Displayed only if there is an activity in progress, to report the current activity, such as Firmware Update in Progress or Service Procedure in Progress. NOTE: Displayed for NonStop NS14000 series and NS16000 series servers only. Activity Start Time The time the current acivity began. NOTE: Displayed for NonStop NS14000 series and NS16000 series servers only. Activity in Progress If yes, displays the Activity and Activity Start Time attributes.
When a Blade Complex has multiple Blade Elements, they are identified in the OSM tree pane as 400.1, 400.2, and 400.3. In the Attributes tab, the Serial Number attribute translates those values to A, B, and C. What OSM displays under the Blade Element object depends on the type of your HP Integrity NonStop server. For NonStop NS14000 series and NS16000 series servers, OSM displays: • • Two Blade Element Power Supply objects. A Blade Element Firmware object.
Physical Fan Assembly (Slot 17) Status Status of the Blade Element fan located in slot 17. Possible values include OK, Fault, Down. NOTE: Displayed for Integrity NonStop NS14000 series and NS16000 series servers only. For other NonStop NS-series servers, fan status is reported under the Fan Assembly objects. Fan Assembly (Slot 18) Status Status of the Blade Element fan located in slot 18. Possible values include OK, Fault, Down.
Physical Location The values displayed by these attributes are assigned through the Set Physical Location action. Rack Name A user-defined name assigned to identify the rack in which the Blade Element is located. Rack Offset A number (from 1 to 42) assigned to describe the location of the Blade Element within the rack. Locator An optional text string assigned to further identify the physical location of the Blade Element.
Power Down Blade Element For Integrity NonStop NS-series systems, this action effectively disconnects this Blade Element from the system and puts the Blade Element into low power mode, enabling it to be serviced. • • • For NonStop NS14000 series and NS16000 series servers, the Blade Element remains in low power mode for 5 minutes.
Set LED State Available for NonStop NS14000 series and NS16000 series servers only, this action allows you to set the Blade Element front or rear (service side) amber LEDs to On or Off. Set Locator LED State Allows you to set the Blade Element locator LED to On or Off. For rx2620, On causes the locator LED to blink. For rx2660 blades and and rx2800 i2 blades, On causes the locator LED to remain on continuously.
Blade Element Firmware This object exists in OSM to display the many firmware attributes that exist for Integrity NonStop NS14000 series and NS16000 series Blade Elements. For these types of systems, the Blade Element firmware is updated through a guided procedure launched by the Firmware Update action located under the Blade Complex object.
Running Compare State The difference, if any, between the current Running image and default Primitive State firmware version. Values Shadow Compare State The difference, if any, between the current Shadow image and default Primitive State firmware version. Values Disk Boot Firmware Running Version The version of the Disk Boot firmware currently running on the processor Blade Element.
PAL/SAL Firmware Running Version The version of the PAL/SAL firmware currently running on the processor Blade Element. Shadow Version The version of the PAL/SAL firmware currently designated as the Shadow image of the blade element firmware. Default File Name The version of the firmware to be used for a PAL/SAL firmware update. Default File Version The version of the HSS PAL/SALfirmware to be used for a firmware update.
Attributes Blower Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values LED State Indicates whether or not the blower’s (amber) fault LED is blinking. Value: Blinking or Off Type The vendor hardware type. Device State The state of the component as known to the operating system on the server. Values Physical Logical Actions Blink LED Off Turns off the blinking of the blower’s (amber) fault LED.
Physical Hardware Revision A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Manufacturer Identifies the manufacturer of the component. Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. Power State Indication of whether the component is powered on. Values Track ID A unique serial number that identifies the component.
• • • • • • • • • • • FC Card Hard Disk InfiniBand HCA Card (G6 CLIMs only) Motherboard (G6 and Gen8 CLIMs only) NIC PCI Riser Power Supply Processor SAS Card ServerNet Interface Card Smart Array Controller (G6 and Gen8 CLIMs only) To update firmware on CLIM components, you can use the actions located on the individual component objects within the OSM Service Connection or the Down System CLIM Firmware Update Tool.
Storage Software Version The version of storage software running on the CLIM. Temperature Status Indicates whether or not the CLIM has exceeded its temperature threshold for proper operation. The possible values are “Temperature sensing not supported by this system,“ “Normal”, “Degraded,” and “Critical.” If the value is not available, this attribute is not displayed. Up Physical Network Interfaces List of physical Ethernet interfaces on the CLIM that are operational.
Physical Model The model number of the CLIM that was assigned in manufacturing. Part Number The part number of the CLIM that was assigned in manufacturing. Serial Number The serial number of the CLIM. Physical Location The values displayed by these attributes are assigned through the Physical Configuration Tool. Rack Name A user-defined name assigned to identify the rack in which the CLIM is located. Rack Offset A number (from 1 to 42) assigned to describe the location of the CLIM within the rack.
ROM Version -- the version of the ROM firmware running on the CLIM. Compare State Indication of the differences, if any, between the current and default ROM firmware versions. Values Default File Name The name of the file to be used for an ROM firmware update. Default File Version The version of the firmware to be used for an ROM firmware update. Version The version of the ROM firmware running on the CLIM.
object, although CLIM subcomponents, such as the Hard Disk object will not be displayed by OSM if SNMP is not available. Restore CLIM Configuration Restores the CLIM configuration from a previously saved file at a user-specified or default location. Restore Default Storage Path Configuration Valid for Storage CLIM only. OSM issues a SPI command to the storage subsystem to restore the active paths of all storage devices using the CLIM to their default configurations. ROM Update Updates the ROM firmware.
Actions Collect CLIM Logs This action finds and collects CLIM logs, saving them to a subvolume location on the NonStop system specified through the Set Location for CLIM Log Collection action. If no location is specified, a default location of $system.zservice will be used.
• • • CLIM FC Firmware CLIM FC BIOS SAS Disk Enclosure (but not individual SAS disk) Firmware NOTE: The Down System CLIM Firmware Update Tool is installed on the NonStop system console as part of the OSM Console Tools product, T0634 G06 ABB and later. It requires SSH SPR T0801^ABA or later. For information on installing the Down System CLIM Firmware Update Tool, see the NonStop System Console Installer Guide.
NOTE: This user must have the necessary OpenSSH access permissions, as described above. Click OK to proceed. The Prepare for Down System CLIM Firmware Update action collects information on all CLIM firmware/BIOS components whose Compare State is not “Same” or “Compatible” and creates a list of the components that need to be updated. This list along with the actual firmware/BIOS binary files is transferred to specified NonStop System Console.
• $ZZCIP.C1002572.1.3 is in the slot 3 that is associated with processor 1; DIMM $ZZCIP.C1002572.2.6 is in the slot 6 that is associated with processor 2. For Gen8 CLIMs, there are 12 DIMM slots, all on a single processor. Location in OSM Tree: System > CLIMs > CLIM > DIMM Attributes DIMM Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Device State The state of the DIMM as known to the operating system on the server.
Logical Active Path The path that is currently accessing the disk. Values: Primary, Backup, Mirror, Mirror Backup Backup Path State The current state of the backup disk path. Values. Logical Device Number The logical device number used by the operating system to identify the disk. Example: 7 Media Size The total size (in kilobytes) of disk storage space. Primary Path State The current state of the primary disk path. Values. Product ID A unique number that identifies the product.
Primary Path Access State The accessibility of the primary path. Values: Inactive, Active Configured Controller Location The location of the primary disk path SCSI controller. Example: PMF.SAC-2.GRP-1.MOD-1.SLOT-50 SCSI Controller A number (1 or 2) that identifies the primary SCSI controller that manages the disk. Example: SCSI Controller (1.1.50.2) SCSI ID An identification number assigned to the device when configured. Actions Abort Backup Path Terminates operation of the backup path to the disk.
NOTE: Contrary to the generic dialog text, for disk firmware you must specify the firmware source file path (established in Step 1). Because disk firmware versions vary, OSM does not use a default file name. If you do not specify a valid file path, the action fails. 6. 7. Enter the firmware source file path (established in Step 1) and click OK. Restart the disk or disks. Power Off Removes power to the disk drive. Power On Restores power to the disk drive.
This action fails if both paths to this disk are down and the mirrored disk is Up. For more information, see Start Disk. Start Disk Use this action to start all paths to the disk drive only when: • • The disk paths are in a Down state. (Hard Down states require a reset action, either Reset Disk, Reset Primary Path, or Reset Backup Path as appropriate.) Its mirrored disk is not currently Up.
Test Verify Runs the power-on self-test for the disk and tests the internal circuitry of the drive. Validate Checksum Scans the user data area of a disk for sector checksum errors. If the action fails, the Action Details dialog box reports a sector checksum and suggests that you spare the sector only if you believe there is a drive media problem. To find additional information, use the OSM Event Viewer.
Backup Path Access State Indicates whether the disk is active or inactive. Configured CLIM The CLIM to which the backup path is configured. LUN The logical unit number of the disk. Example: 101 Disk Pair Disk Pair Name The name and location of the mirrored disk. Example: Disk $SAS25-M. Primary Path Access State Indicates whether the disk is active or inactive. Configured CLIM The CLIM to which the primary path is configured. LUN The logical unit number of the disk.
Clear Data Available only for SAS or SSD disks -- Erases all data on the disk but leaves the disk label intact. Clear Data does not erase the FIR data in the CE sector, the volume label, the boot sector, or the spare tracks table. After a Clear Data completes or is cancelled, the disk drive is not usable until you restore the file system by using the SCF INITIALIZE DISK command. The action prompts you to specify an optional process priority for the action.
Start Primary Path Starts the primary path to this disk drive. When the Start action completes, the primary path is in the Started state. Start Volume Starts all paths for both the primary and mirror drives of this volume. Stop Backup Path Terminates operation of the backup path to the disk. When the Stop action finishes, the path is in a Down state. If the disk drive is currently in use, a dialog box warns you and asks whether or not you want to continue with the action.
Physical Device State The state of the component as known to the operating system on the server. LED State Indicates whether or not the disk drive’s (amber) fault LED is blinking. Value: Blinking or Off Port A Bypass State The state of the Port A Bypass. Possible values include: Bypass Disabled, Bypassed By Disk, Bypassed By User, Bypassed By EMU. Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts.
Primary Path Access State Indicates whether the primary disk path is active or inactive. Configured FSAC Location Displays the configured location of the FCSA FSAC containing the primary disk path controller. This attribute is displayed even if the physical FCSA FSAC is not present. Example: FCSA.SAC-1.GRP-111.MOD-2.SLOT-2 FSAC Identifies the primary FCSA that manages the disk. Example: FCSA FSAC (111.2.2.1) Backup Path Access State Indicates whether the backup disk path is active or inactive.
Clear Data Erases all data on the disk but leaves the disk label intact. Clear Data does not erase the FIR data in the CE sector, the volume label, the boot sector, or the spare tracks table. After a Clear Data completes or is cancelled, the disk drive is not usable until you restore the file system by using the SCF INITIALIZE DISK command. The action prompts you to specify an optional process priority for the action. If not specified, the current default priority is used.
NOTE: With OSM Low-Level Link T0633 AAQ and later, you can also save system configuration files on the system console. Those saved configurations are not displayed as attributes values in the OSM Service Connection, but can be used during the system load operations in the Low-Level Link. For more information, see the OSM Low-Level Link online help. Spin Down Stops the physical spinning of the disk drive. This should be done before removing a disk drive. Both paths must be down for the action to succeed.
Stop Primary Path Terminates the primary path to the disk. When the Stop action finishes, the path is in a Down state. If the disk drive is currently in use, a dialog box warns you and asks whether or not you want to continue with the action. Stop Volume Terminates all paths for the primary and mirror drives of this volume. When the Stop action finishes, the paths are in a Down state. Switch Process Pair Switches the primary and backup disk I/O processes.
Set LED State Sets the LED on the physical disk in the SAS disk enclosure to On or Off. Show SMARTSSD Wear Gauge This action is available for Solid State drives only. It displays the current SMARTSSD Wear Gauge values, which includes estimates for both the amount of life used up for the disk and for the amount of life remaining. A disk with a low percentage of life used can display an unusually high number of hours of life remaining.
Example: E4SA $ZZLAN.E4SA0 (1.1.53) Attributes E4SA Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Hardware Revision A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Manufacturer Identifies the manufacturer of the component. Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts.
During startup, the controller operational code is automatically loaded into the ESAC. When the Start action completes, both the E4SA CRU and the ESAC are in the Started state. Stop Rather than automatically stopping the E4SA (as the Abort action does), this action first warns you if the E4SA is currently in use (and stops it only after you confirm). EMU The Environmental Monitoring Unit (EMU) is a subcomponent of a FCDM.
Each Enclosure object contains these subcomponents: • • • Processor Blades Logical Processors ServerNet Switches Attributes Enclosure Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Enclosure Name The name of the Blade enclosure, as configured through the Onboard Administrator (OA). (This name cannot be changed through OSM.) Manufacturer Identifies the manufacturer of the component.
Bay 1 OA Firmware Version The firmware version currently running on the OA (Onboard Administrator) located in Bay 1 of the enclosure; for example: 2.52. NOTE: When looking at the enclosure from the rear, the bay on the left is bay 1, the bay on the right is bay 2. Bay 2 OA Firmware Version The firmware version currently running on the OA (Onboard Administrator) located in Bay 2 of the enclosure; for example: 2.52. Standby OA IPv4 Address The IPv4 address of the standby OA.
Display Diagnostic Status Errors Displays all diagnostic status errors for the Enclosure. Launch the Onboard Administrator Launches the Onboard Administrator (OA) management page. Prepare Enclosure for Removal Prepares the enclosure for removal. This action is not valid for group 100.
Active Path The path that is currently accessing the disk. Values: Primary, Backup, Mirror, Mirror Backup Primary Path State The current state of the primary disk path. Values. Backup Path Configured FSAC Location Displays the configured location of the FCSA FSAC containing the backup disk path SCSI controller. This attribute is displayed even if the physical FCSA FSAC is not present. Access State Indicates whether the disk is active or inactive. LUN The logical unit number of the disk.
Actions Abort Backup Path Terminates operation of the backup path to the disk. When the Abort action finishes, the path is in a Hard Down state. You must use the Reset Backup Path action before you can start the path again. Abort Disk Terminates operation of all paths for the disk. When the Abort action finishes, the paths are in a Hard Down state. You must use the Reset Disk action before you can start the paths again. Abort Primary Path Terminates operation of the primary path to the disk.
Stop Disk Terminates all paths for this disk drive. When the Stop action finishes, the paths are in a Down state. If the disk drive is currently in use, a dialog box warns you and asks whether or not you want to continue with the action. Stop Primary Path Terminates the primary path to the disk. When the Stop action finishes, the path is in a Down state. If the disk drive is currently in use, a dialog box warns you and asks whether or not you want to continue with the action.
Physical Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. Track ID A unique serial number that identifies the component. Track IDs are used for tracking components. Hardware Revision A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Logical Device Number The logical device number used by the operating system to identify the disk.
Primary Path SCSI ID An identification number assigned to the device when configured. SCSI Controller A number (1 or 2) that identifies the primary SCSI controller that manages the disk. Example: SCSI Controller (1.1.50.2) Access State The accessibility of the primary path. Values: Inactive, Active Configured Controller Location The location of the primary disk path SCSI controller. Example: IOMF2.SAC-2.GRP-1.MOD-1.SLOT-50 Version The version of the firmware running on the disk.
Reset Disk Places the disk in a state from which it can be started. This action might be necessary if the disk was in a STOPPED state, substate HARDDOWN; a hardware error has occurred; the disk was stopped with an ABORT command; or a STOP or ABORT fails to put the disk into the STOPPED state, substate DOWN. Reset Primary Path Places the primary path in a state from which it can be started. Reset Volume Places the volume in a state from which it can be started.
Switch to Primary Path Switches processing from the backup to the primary path. Test Verify Runs the power-on self-test for the disk and tests the internal circuitry of the drive. Validate Checksum Scans the user data area of a disk for sector checksum errors. If the action fails, the Action Details dialog box reports a sector checksum error and suggests that you spare the sector only if you believe there is a drive media problem. For additional information, use the OSM Event Viewer.
Physical Manufacturer Identifies the manufacturer of the component. Power State Whether the component is powered on. Values Enabled State The current state of the fan as known to the operating system. Values Logical Rotations Sensor Normal Minimum Value The minimum acceptable fan speed is 1800 RPM. If the speed falls below 1800, an alarm is generated. Current Value The current fan speed, measured in rotations per minute (RPM).
Actions None Fan (CLIM) A subcomponent of the CLIM. Location in OSM Tree: System > CLIMs > CLIM > Fan Attributes Fan Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Device State The state of the fan as reported by OSM. Possible values include: OK, Degraded, Fault, Not Installed. Logical Actions Replace Launches a documented service procedure to replace a fan in a CLIM.
Actions Set LED State Turns on or off the amber LED located on the fan. The current state is indicated by the LED State attribute. Fan (Processor Switch) One of two FRUs that provide cooling for the components in a processor switch. Location in OSM Tree: System > Fabric Group > Internal ServerNet Fabric > Processor Switch > Fan Example: Fan (100.2.16) Attributes Physical LED State Indicates whether or not the power supply’s amber LED is lit. This state is determined by the Set LED State action.
Fan (VIO) A component of VIO enclosures (represented in the OSM Service Connection as VIO modules) that circulates air into the enclosure to help maintain optimal temperature. There are two fans in each VIO enclosure. Attributes Physical LED State Indicates whether or not the fan’s amber LED is lit. This state is determined by the Set LED State action. Value: On or Off Manufacturer Identifies the manufacturer of the component. Displayed for VIO fans in S-series VIO modules only.
BIOS Compare State Indication of the differences, if any, between the current and default BIOS versions. Values Default File Name The name of the file to be used for a BIOS update. Default File Version The version of the firmware to be used for a BIOS update. Version The version of the BIOS running on the FC card. Compare State Indication of the differences, if any, between the current and default firmware versions. Values Default File Name The name of the file to be used for a firmware update.
Logical Device State The state of the component as known to the operating system on the server. Values Vendor Hardware Revision A code that identifies the generation of the component provided by its supplier. Device Connection Configured Controller Location The location of the configured FCSA connected to the FC-AL I/O Module. Example: FCSA.FSAC-1.GRP-111.MOD-2.SLOT-1 Fibre Channel Controller The number that identifies the FCSA FSAC connected to the FC-AL I/O Module. Example: FCSA FSAC (111.2.1.
Physical Manufacturer Identifies the manufacturer of the component. Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. Serial Number The serial number of the component assigned to it by the supplier of the component. Type The vendor hardware type. Physical Location The values displayed by these attributes are assigned through the Set Physical Location action.
Actions Blink All LEDs Off Turns off the blinking of the fault LEDs on the FCDM, disks, FC-AL I/O module, power supplies, and fans. Blink All LEDs On Causes the fault LEDs on the FCDM, disks, FC-AL I/O module, power supplies, and fans to blink. Disable All Drive Bypass Opens up the specified port or ports (A and/or B) on all disk drives in the FCDM for use. Enable All Drive Bypass Shuts down the specified port or ports (A and/or B) on all disk drives in the FCDM.
contains only one FCDM, it is not daisy-chained. Other FCDMs that are not daisy-chained appear under separate in FCDM Collection objects. The FCDM Collection object appears within the same group object as the IOAM enclosure to which the FCDM is connected. If the FCDM is connected to Fibre Channel ServerNet adapters located in different IOAM enclosures (for increased fault tolerance), OSM displays the FCDM Collection in the lower-numbered group.
Attributes FCSA Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Hardware Revision A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. Track ID A unique serial number that identifies the component.
When initiated, OSM checks for any connected paths that do not have a backup and warns you of any connectivity loss that could result from continuing with the action. OSM also directs you to the online help for precautionary guidelines for handling the hardware. See: • • Removing the FCSA Installing the Replacement FCSA Once you confirm that the FCSA has been replaced, OSM presents these options for bringing up the paths associated with this adapter: • Bring up and balance.
Installing the Replacement FCSA NOTE: Whenever you handle a FCSA, follow standard operating practices to avoid damage to the equipment. Review the standard operating practices documented in the Fibre Channel ServerNet Adapter Installation and Support Guide. 1. Unpack and inspect the FCSA: a. Put on an ESD wrist strap and attach the grounding clip to the antistatic mat. b. Place the package containing the FCSA on the antistatic mat. c. Open the packing container and remove the FCSA.
7. Connect the Fibre Channel cables to the Fibre Channel ports on the FCSA by lining up the retaining clips with the ports and gently inserting them into the ports, one at a time. The green power-on LED at the bottom of the adapter should now be lit. If the LED is not lit, either reseat the FCSA or install a different FCSA. 8. After you install the new FCSA, refer to the Fibre Channel ServerNet Adapter Installation and Support Guide for information about resuming operations.
The Fast Ethernet ServerNet adapter (FESA) CRU contains one Fast Ethernet ServerNet addressable controller (SAC), which contains one Ethernet physical interface, that corresponds to the one Ethernet port on each FESA CRU. Location in OSM Tree: System > Group > Module > FESA Slot Location: FESA CRUs can be located in slots 51, 52, 53, and 54 in IOMF2 enclosures (service side). Example: FESA $ZZLAN.FESA1 (1.1.
Fiber OSM displays four Fiber objects under the ServerNet Ports on a ServerNet Switch in blade enclosures. Location in OSM Tree: System > Enclosure > ServerNet Switch > Port > Fiber. Attributes None. Fiber Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Link Status The state of the component as known to the operating system on the server. Values Logical Neighbor Check Status Actions None.
Firmware Revision The version of the firmware running on the router. Device Status Indicates whether the router is Up or Down. Associated Device Tape Drive The names of the one or two tape drives associated with the router. Physical Location The values displayed by these attributes are assigned through the Physical Configuration Tool. Rack Name A user-defined name assigned to identify the rack in which the Fibre Channel Router is located.
Hardware Revision The hardware revision of the switch logic board. CRU Type The type of CRU this SAC is connected to. Values: SSAC, FSAC, SCSI Configured Type The type of storage device supported by this Fiber SAC. Values: Disk, Tape, SCSI Controller, Not Configured, Unknown Logical Actions Responsive Test Verifies that the component is connected and responding. G4SA The M8800 Gigabit Ethernet 4-port ServerNet adapter (G4SA) provides Gigabit connectivity between NonStop servers and Ethernet LANs.
Actions Abort Terminates operation of the G4SA and the associated Ethernet ServerNet addressable controller (SAC). When the Abort action finishes, the G4SA and the SAC are in the Stopped state. Add This action is displayed in OSM only when a G4SA is first inserted and not yet configured. Performing this action ensures that the Configured Type is set to G4SA. Delete Deconfigures the G4SA, removing the associated G4SA SAC and PIF objects.
Logical Configured Interface Type Displays the configured interface, as specified by the Alter Interface Type action. Values: Copper, Fiber, or Autodetect. Current Configured Speed The transmission rate for the ServerNet addressable controller. Device State The state of the component as known to the operating system on the server. Values Duplex Mode The transmission mode for the ServerNet addressable controller.
Each G4SA SAC contains up to four G4SA PIFs, which correspond to the four Ethernet ports on each G4SA. Location in OSM Tree: System > Group > IOAM Enclosure > IOAM > G4SA > G4SA SAC or, in a VIO enclosure: System > Fabric Group 100 > Internal ServerNet Fabric > VIO Module > G4SA > G4SA SAC Example: G4SA SAC $ZZLAN.G4SA1.0 Attributes G4SA SAC Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK.
Actions Abort Terminates operation of the G4SA ServerNet addressable controller. When the Abort action finishes, the SAC is in the Stopped state. Dump Copies a memory image from a G4SA SAC to a file on the local system. The file will be the last (highest numbered) file of the chain started with the file specified in the Dump File Name attribute of the SAC. CAUTION: The SAC and PIFs will be unavailable while the SAC is being dumped. Firmware Update Updates the boot firmware for the G4SA SAC.
Physical Hardware Revision A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Manufacturer Identifies the manufacturer of the component. Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. Power State Whether the component is powered on. Values Track ID A unique serial number that identifies the component. Track IDs are used for tracking components.
Attributes Group Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Service LED State Indication of whether the service LED is on or off. On: An OSM user has turned on the service LED by using the Set Service LED State action. Logical Off: An OSM user has turned off the service LED by using the Set Service LED State action. Turning on the group service LED helps you locate the group for servicing.
IOAM Group An IOAM Group contains an I/O Adapter Module enclosure and FCDM Collection objects, which contain Fibre Channel disk modules (FCDMs) that are connected to this IOAM enclosure. If an FCDM is connected to FCSAs located in different IOAM enclosures (for increased fault tolerance), OSM displays the FCDM Collection in the lower-numbered group. For an HP Integrity NonStop NS16000 series server, numbering of IOAM groups starts at 110.
Attributes Hard Disk Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Firmware Firmware Version The version of the firmware running on the CLIM hard disk. Example: HPD5 Physical Model The model number of the CLIM hard disk that was assigned in manufacturing. Serial Number The serial number of the CLIM hard disk. Device State The state of the CLIM hard disk as known to the operating system on the server.
Number of Ports The number of physical ports on the InfiniBand HCA card. System Image GUID A text string indicating the System Image GUID of the InfiniBand HCA. It is obtained through an SNMP call. If the value is not available (for example, because the Maintenance Interface IP address is not available or the InfiniBand SNMP Agents are not functioning properly), it is displayed as “Not Available.” Hardware Revision A code that identifies the generation of the InfiniBand HCA Card.
Actions Group Connectivity ServerNet Path Test You can perform this action on either the Internal ServerNet X Fabric or the Internal ServerNet Y Fabric. The action tests the links between SPs and ServerNet Switch Board maintenance entities (MEs) that provide ServerNet communication between groups on the system. Processor-to-Processor Connectivity Test Equivalent to the SCF STATUS SERVERNET command, this action tests the ServerNet connectivity between specified processor on this Internal Fabric.
IOAM names in OSM include the group number and a module number of either 2 or 3. For example, IOAM 13.2 is located in group 13, module 2. The other IOAM in this IOAM group is IOAM 13.3. NOTE: If for any reason a ServerNet switch board is not present in a module, the fans, power supplies, and adapters in that module will not appear in OSM. Location in OSM Tree: System > Group > IOAM Enclosure > IOAM Example: IOAM 13.
Physical Location The values displayed by these attributes are assigned through the Set Physical Location action. Rack Name A user-defined name assigned to identify the rack in which the IOAM enclosure is located. You can enter up to 15 alphanumeric characters. Rack Offset A number (from 1 to 42) assigned to describe the location of the IOAM enclosure within the rack. Locator An optional text string assigned to further identify the physical location of the IOAM enclosure.
IOMF2 (I/O Multifunction 2) Each I/O multifunction 2 (IOMF2) CRU in a NonStop server contains these components: • • • • A service processor (SP) Two internal SCSI controllers One external SSAC A ServerNet plug-in card (PIC), which provides connectivity to internal ServerNet fabrics Location in OSM Tree: System > Group > Module > IOMF2 Slot Location: IOMF2 CRUs are located in slots 50 and 55 of Nonstop S-series I/O enclosures (service side). Example: IOMF2 (1.1.
Rail Maximum Voltage The maximum voltage limit (60 volts) for the IOMF2 CRU. Rail Minimum Voltage The minimum voltage (39.6 volts) that must be available to power the IOMF2 CRU. SCSI-X Voltage The voltage of the SCSI-X path, the primary path used for disks on a system. SCSI-Y Voltage The voltage of the SCSI-Y path, the path configured for mirrored disks on a system. Storage ASIC Initialization State The status of the storage ASIC in the CRU.
Storage ASIC Initialization Test Prompts the storage subsystem manager process ($ZZSTO) to initialize the storage ASIC in the CRU. If initialization fails, an alarm is generated. This action is triggered automatically when a new CRU is inserted while OSM is running or when an (SCF) STATUS ADAPTER command is issued. If a CRU is inserted while OSM is not running, perform this action after logging on to the OSM Service Connection. Test Verify Performs basic tests on the CRU.
Logical Processor The OSM Service Connection displays Logical Processor objects for both HP Integrity NonStop BladeSystems (J-series software) and Integrity NonStop NS-series servers (H-series software); what OSM displays depends on the type of system: • For Integrity NonStop BladeSystems, OSM displays a Logical Processor object for each processor blade physically present in the Enclosure.
Processor Blade Valid only for NonStop BladeSystems, this attribute maps the Logical Processor to the Processor Blade it represents. Processor Freeze State Indicates whether the processor freeze state is enabled or disabled. Processor State (from ME) The state of the Logical Processor as seen by the Maintenance Entity (ME) of the associated ServerNet Switch Board. Values Processor Type The NonStop server type.
Enable Processor Freeze Turns the Freeze Enable flag on this processor on. If the OSM Low-Level Link System Freeze attribute is set to Enabled, a freeze-enabled processor might freeze if either another freeze-enabled processor halts, or the (Low-Level Link) system-level Freeze action is performed. Halt Terminates all processes running on this processor. Halting a processor does not affect any other processors in the system. CAUTION: Halting a processor might result in unrecoverable loss of data.
Maintenance PIC Located in slot 1 of a processor switch in NonStop NS-series servers that contain processor switches. Attributes Physical Hardware Revision A code that identifies the generation of the component. Hardware revision codes are used for tracking components. LED State Indicates whether or not the power supply’s amber LED is lit. This state is determined by the Set LED State action. Value: On or Off Model Identifies the plug-in card type as being a Maintenance PIC.
Firmware Revision The version of the firmware running on the switch. IPv4 Address The IPv4 address of the switch. Lines Connected Lists the port numbers of ports on the switch that have lines connected. Lines Disconnected Lists the port numbers of ports on the switch that have been disconnected (since the OSM server has been running).
Attributes Memory Card Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Physical Hardware Revision A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. Track ID A unique serial number that identifies the component.
Locator An optional text string assigned to further identify the physical location of the module. This attribute is displayed only if a value is specified using the Set Physical Location action. Alarm Panel Identifier For DC-powered Telco systems only. Displays the system alarm panel (SAP) identifier for this hardware resource, as specified through the Alarm Panel Identifier option within the Set Physical Location action. This attribute is displayed only if a value is specied through the action.
• • Locator is an optional text string to help identify the physical location of the module. It must contain alphanumeric characters only. This parameter, used for DC-powered Telco systems only, allows you to specify a system alarm panel (SAP) identifier, which is then displayed in OSM by the Alarm Panel Identifier attribute for this hardware resource.
NOTE: * SNMP Read Access Community and SNMP Write Access Community user groups and access privileges are established by the administrator for the UPS. For information on how an administrator configures these user groups, see the OSM Configuration Guide. Motherboard (CLIM) A subcomponent of G6 and Gen8 CLIMs. Location in OSM Tree: System > CLIMs > CLIM > Motherboard Attributes None. Actions Replace Launches a documented service procedure to replace a CLIM motherboard.
Default File Version The version of the firmware to be used for an NIC firmware update. Version The version of the NIC firmware running on the CLIM. Actions Firmware Update Updates the firmware running on the NIC. Upon completion, OSM offers to reboot the CLIM, in order for the CLIM to start using the updated firmware. Replace Launches a documented service procedure to replace a NIC in a CLIM.
Track ID A unique serial number that identifies the component. Track IDs are used for tracking components. Type Identifies the type of ServerNet PIC. Value: Optical Extender PIC Device State The state of the component as known to the operating system on the server. Values Logical Actions Power Off Shuts off power to the Optical Extender PIC. Power On Restores power to the Optical Extender PIC. Replace Launches a service procedure describing how to replace an Optical Extender PIC.
Attributes PIC Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Type Indication of the type of plug-in card. Values: NNA, Serial Copper, ECL, Long-Haul Fiber, Short-Haul Fiber Connector Number A unique number used to distinguish between plug-in cards on an MSEB CRU. Physical Logical Actions Clear Loopback Test Clears the loopback test on a plug-in card (PIC).
The external loopback test indicates whether or not the PIC circuitry is operational or faulty. Unlike the internal loopback test, the external loopback test also checks the connector on the PIC. CAUTION: Do not use the external loopback test on a PIC that you believe is operating normally. Doing so shuts down ServerNet traffic through the PIC for the duration of the test (several minutes).
Logical Current Configured Speed Valid only for FESA and GESA PIFs. The transmission rate for the ServerNet addressable controller. Device State The state of the component as known to the operating system on the server. Values Duplex Mode The transmission mode for the ServerNet addressable controller. Values: Half Duplex, Full Duplex, Unknown Hardware MAC Address The media access control (MAC) address of the PIF hardware. Interface Type Displayed for CCSA PIFs only.
PMCU The power monitor and control unit (PMCU) controls and monitors the battery connection to the DC power distribution buses. Along with the service processor, the PMCU diagnoses the condition of the batteries, fans, and power supplies and regulates the voltage supplied to the fans. Location in OSM Tree: System > Group > Module > PMCU Slot Location: PMCUs are located in slots 21 and 22 of Nonstop S-series I/O enclosures (appearance side). Example: PMCU (1.1.
Slot Location: CRU: Power supply CRUs are located in slots 31 and 32 of enclosures containing IOMF2 CRUs. Example: Power Supply (1.1.31) Attributes Power Supply Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Manufacturer Identifies the manufacturer of the component. Power State The state of the power supply CRU as known to the operating system on the server.
NOTE: In DC-powered Telco systems, instead of having power supply units in slots 31 and 32, there are actually 4 TICs (in positions A1, A2, B1, and B2). If the system is not wired as documented in the NonStop S-Series Central Office Server Installation and Service Guide, OSM cannot properly identify the TIC that needs to be replaced.
• • 2. Handle with care -- the power supply weighs approximately 5.6 kilograms (14 pounds). Follow these standard operating practices when replacing CRUs: — Replace only one CRU at a time. Attempting to replace more than one hardware component at a time might cause serious system outages, processor halts, and connectivity problems. — Remove all jewelry and metal accessories, such as rings, watches, and necklaces, before working with the equipment.
3. Lower the ejector on the power supply to its fully open position. This action disconnects the power supply from the power interface board (PIB) and the AC power cord directly behind it. 4. With one hand, grasp the handle of the power supply and slide the power supply partway out of the slot. Using your other hand to support the weight of the power supply, slide the power supply all the way out of the slot. 5.
Installing the Replacement Power Supply 1. Lower the ejector on the replacement power supply to its fully open position. 2. With one hand, grasp the handle of the power supply. Use your other hand to support the weight of the power supply. Then slowly push the power supply all the way into the empty slot. Raise the ejector on the replacement power supply to its fully closed position. This action connects the power supply to the power interface board (PIB) and the AC power cord directly behind it. 3.
Physical Device State The state of the Blade Element Power Supply, as known to the operating system on the server. Possible values include OK, Fault, Power Loss, and Power Supply Fan Fault. Manufacturer Identifies the manufacturer of the component. Displayed for NonStop NS14000 series and NS16000 series servers only. Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts.
Attributes Power Supply Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values LED State Indicates whether or not the power supply’s (amber) fault LED is blinking. Value: Blinking or Off Type The vendor hardware type. AC Power State Whether the power source is On or Off. Device State The state of the component as known to the operating system on the server.
Attributes IOAM Power Supply Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Hardware Revision A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts.
For an Integrity NonStop NS14000 or NS1000 system, you must use this action to configure at least one of your IOAM power supplies (to specify UPS as the backup power source) in order for OSM to provide an orderly system shutdown in the event that a power failure exceeds the powerfail-delay time interval specified for your UPS. For more information on preparing for AC power-fail scenarios, see the NonStop NS14000 or NS1000 Planning Guide.
Configure Power Source as UPS Sets the Power Source attribute value for this power supply unit to UPS. You must be logged on as super.super to perform this action. Upon initiating the action, you are prompted to enter the IPv4 address of the UPS.
Power Supply (VIO) Provides power to the VIO enclosure (represented in the OSM Service Connection as a VIO module). There are two VIO power supplies in each VIO enclosure. Attributes VIO Power Supply Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Manufacturer Identifies the manufacturer of the component. Displayed for VIO power supplies in S-series VIO modules only.
that a power failure exceeds the powerfail-delay time interval specified for your UPS. For more information on preparing for AC power-fail scenarios, see the Planning Guide for your NonStop system. For more information on using the POWERFAIL_DELAY_TIME command to specify the Power-Failure-to-Shutdown time interval, see the SCF Reference Manual for the Kernel Subsystem. NOTE: This action is not valid for a power supply unit in an S-series VIO Module.
Location in OSM Tree: System > Enclosure > Processor Blade Attributes Processor Blade Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. Product Name The product name of the component as assigned by the manufacturer. Replacement Part Number The replacement part number of the component.
Retrieve and Clear BMC Event Log - Formatted Allows you to retrieve and save a formatted version of the Baseboard Management Controller (BMC) event log and then clear the BMC event log. NOTE: With T0682 AAN and later, OSM saves a copy of each Blade Element's BMC event log to a file in $system.zservice and clears the BMC event log daily between 1 and 2 a.m. The log file name is the format blMMMSDD, where MMM is Blade Element's module number, S is slot number, and DD is date of the month.
PE (A/B/C) Reintegration Enable State Indicates whether or not the PE is enabled for automatic reintegration in case of a failure. NOTE: Displayed for NonStop NS14000 series and NS16000 series servers only. PE (A/B/C) Reintegration Progress Displayed only if a PE reintegration is in progress, this attribute displays the progress in terms of percentage complete. NOTE: Displayed for NonStop NS14000 series and NS16000 series servers only.
Serial Number The serial number of the component assigned to it by the supplier of the component. Slot ID The ID of the slot in which the LSU logic board resides. LSU Optics Adapter NOTE: only. These attributes are displayed for NonStop NS14000 series and NS16000 series servers Hardware Revision A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Part Number The part number of the component that was assigned in manufacturing.
Replace LSU Displays the procedure for replacing LSU Logic Board and Optics Adapter components. Reset LSU Resets the LSU.
Processor switch modules are initially configured using the Configure Module action in the OSM Low-Level Link, as described in the NonStop NS-Series Hardware Installation Manual (available in the Hardware Service and Maintenance collection of NTL).
Rediscover Causes OSM to refresh and reanalyze the processor switch and all subcomponents. Refresh refers to OSM updating the attribute values displayed in the OSM Service Connection interface. Reanalyze refers to the running of OSM incident analysis, which checks EMS event messages and creates alarms in OSM if certain conditions exist. Replace Launches an OSM guided procedure with step-by-step instructions for replacing the processor switch chassis or subcomponents.
CRU SACs in CRU PIFs in SAC GESA 1 1 TRSA 1 1 Location in OSM Tree: System > Group > Module > CRU > SAC Slot Location: SACs are located on the CRUs that might be installed in slots 53 and 54 in processor enclosures (service side) or in slots 51, 52, 53, and 54 in I/O enclosures (service side). Example: E4SA SAC $ZZLAN.E4SA0.0 Attributes SAC Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK.
Processor Access List The currently available processors that can access the SAC. Example: 0,1 SAC Type Displayed for CCSA SACs only, displays the type of CCSA SAC (for example: SS7TE3A). Version The version of the boot firmware for the SAC. Default File Name The name of the file to be used for a (boot) Firmware Update. Default File Version The version of the firmware to be used for a (boot) Firmware Update.
Attributes Physical Model The product name of the SAS card. Serial Number The serial number of the SAS card. Connected Enclosures A list of the SAS Disk Enclosure(s) to which the SAS card is attached. Compare State Indication of the differences, if any, between the current and default BIOS versions. Values Default File Name The name of the file to be used for a BIOS update. Default File Version The version of the firmware to be used for a BIOS update.
NOTE: For a SAS Disk Enclosure in a Telco system, the fans and power supplies are represented in OSM by a pair of SAS Power Supply and Fan objects. Attributes SAS Disk Enclosure Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Manufacturer Identifies the manufacturer of the component. Model The model number of the SAS disk enclosure that was assigned in manufacturing.
Firmware Compare State Indication of the differences, if any, between the current and default firmware versions. Values Default File Name The name of the file to be used for a firmware update. Default File Version The version of the firmware to be used for a firmware update. Version The version of the firmware running on the SAS disk enclosure. Actions Firmware Update Updates the firmware on the SAS Disk Enclosure.
Logical SCSI ID The ID to which the device answers on the SCSI bus: 4 or 5: Tape devices 6 or 7: Controllers 8 and 9: SCSI extenders/FC converters The remaining IDs are for the device on the SCSI bus. SCSI Bus Number The bus to which the device is attached: Bus 1 or 2: Internal device Bus 3: External device Actions Responsive Test Verifies that the component is installed and responding.
NOTE: Displayed only for (J-series) NonStop BladeSystems; not applicable for NonStop NS-series servers. ServerNet Interface Card (CLIM) A subcomponent of the CLIM. Location in OSM Tree: System > CLIMs > CLIM > ServerNet Interface Card Attributes ServerNet Interface Card Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Model The product name of the ServerNet interface card.
Track ID A unique serial number that identifies the component. Track IDs are used for tracking components. Type Identifies the type of ServerNet PIC. Value: Quad Single Mode Fibre, Dual Single Mode Fibre, Quad Multi Mode Fibre, Dual Multi Mode Fibre, Crosslink, LoopBack, Maintenance Device State The state of the component as known to the operating system on the server. Values Logical Actions Enable ServerNet Port Enables the specified ServerNet port on this PIC.
• Optical Extender PICs located only in HP Integrity NonStop NonStop NS14000 series, NS2000 series, NS2100, NS2200 series, NS2300, NS2400 series, NS1200, or NonStop NS1000 systems containing VIO enclosures. In slot 2, an extender PIC can be used for connectivity to additional processors, with ports 1 through 4 corresponding to processors 4 through 7. In slot 5 (Integrity NonStop NS14000 series servers only), an extender PIC can be used for ServerNet cluster connectivity.
Replacement Part Number The replacement part number of the component. Serial Number The serial number of the component assigned to it by the supplier of the component. Logical IPv4 Address The IPv4 address of the ServerNet switch. Operational Status The status of the ServerNet switch, as seen by the Onboard Administrator (OA). Time of Last Reset The date and time of the last hard or soft reset of the ServerNet Switch Board.
NOTE: Because the hard reset required to complete an FPGA update disrupts a ServerNet fabric, you should perform a Check Storage Dependence on ServerNet Fabric action to make sure it is safe before proceeding with the FPGA update. Then, update the ServerNet switch boards on a single fabric at a time and wait at least 5 minutes after completion before checking storage dependence and updating the switch boards on the other fabric.
Physical Hardware Revision A code that identifies the generation of the component. Hardware revision codes are used for tracking components. LED State Indicates whether the ServerNet Switch Board LED is on or off. Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. Track ID A unique serial number that identifies the component. Track IDs are used for tracking components.
ME FPGA Update Allows you to update the FPGA code file for the Maintenance Entity (ME) of the ServerNet Switch Board. NOTE: Because the hard reset required to complete an FPGA update disrupts a ServerNet fabric, you should perform a Check Storage Dependence on ServerNet Fabric action to make sure it is safe before proceeding with the FPGA update.
Logical Current Topology The maximum processor configuration for the service processor. Values Device State The state of the service processor: Active (Primary): This is the active SP and it is available. Active (Secondary): This is not the active SP, but it is available. Firmware Update Mode: An SP firmware update is in progress. In Test: Temporary state during power-on self-test. Initializing: Temporary state during startup.
Processor Boot Millicode Firmware These attributes are displayed only for SPs located in PMF or PMF2 CRUs; not for those in IOMF or IOMF2 CRUs. Version The version of the firmware on the processor on the same PMF CRU with this service processor. Default File Name The name of the file to be used for the Processor Boot Millicode firmware update. (CPUCODE9) Default File Version The version of the firmware to be used for the Processor Boot Millicode firmware update.
Physical Model The model number of the Smart Array Controller that was assigned in manufacturing. Serial Number The serial number of the Smart Array Controller. Compare State Indication of the differences, if any, between the current and default Smart Array Controller firmware versions. Values Default File Name The name of the file to be used for a Smart Array Controller firmware update. Default File Version The version of the firmware to be used for a Smart Array Controller firmware update.
Storage ASIC Initialization State The status of the storage ASIC in the CRU. Values: Initialized, Not Initialized, Unknown Actions Replace Launches the Replace SNDA guided procedure, which provides step-by-step instructions for replacing the ServerNet/DA CRU. Storage ASIC Initialization Test Prompts the storage subsystem manager process ($ZZSTO) to initialize the storage ASIC in the CRU. If initialization fails, an alarm is generated.
Logical Configured Type The type of device supported by this SAC. Values: Disk, Tape, SCSI Controller, Not Configured, Unknown Actions Responsive Test Verifies that the component is connected and responding.
Device State The state of the component as known to the operating system (open scsi process) on the server. Values Configured Controller Location The location of the configured SCSI controller. Example: PMF.SAC-3.GRP-1.MOD-1.SLOT-55 Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. This is not the spare part number.
Each SWAN 2 CRU contains these subcomponents: • Up to six SWAN 2 CLIPs, each of which contains two SWAN Paths and two WAN Lines, giving each SWAN 2 CRU as many as twelve WAN ports • Two LAN Logic Board CRUs • Two Fan CRUs • Two Power Supply CRUs • One Battery Location in OSM Tree: System > SWAN Collection > SWAN [or SWAN2] Slot Location: WAN CRUs are external to the enclosures. Example: SWAN2 $ZZWAN.
Alternate Subnet Name The name of the subnet on the alternate TCP/IP process that supports the SWAN concentrator. Format: TCPIP process name.subnet name Example: $ZTCP3.#SN1 Primary Gateway IPv4 Address The primary gateway IPv4 address configured for the SWAN concentrator. Example: 192.168.10.30 Alternate Gateway IPv4 Address The alternate gateway IPv4 address configured for the SWAN concentrator. Example: 192.168.11.
Stop Terminates operation of the SWAN concentrator and all associated SWAN CLIPs. When the Stop action completes, the SWAN CRU and associated SWAN CLIPs are in the Stopped state. Verify Logical Configuration Verifies that the SWAN Concentrator CRU is properly configured. If not, an Incorrect Logical Configuration alarm is generated on the CRU. SWAN Battery A subcomponent of the SWAN 2 CRU that provides backup power for 30 seconds in the event of a power outage.
Logical Device State The state of the component as known to the operating system on the server. Values Physical The Physical attributes are displayed for SWAN 2 CLIPs only. Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. Track ID A unique serial number that identifies the component. Track IDs are used for tracking components. Hardware Revision A code that identifies the generation of the component.
Test Basic Online Runs an online test to determine if the CLIP is functional, and checks that both the access paths are available. Test Full Path Access Tests two-way access to the communications line interface processor (CLIP) using both the primary and alternate addresses. Test Primary Path Access Tests two-way access to the communications line interface processor (CLIP) using the primary address Test Verify Runs the power-on self-test for the CLIP. The FAULT LED on the CLIP flashes during the test.
Actions None. SWAN LAN Logic Board (LANLB) Each SWAN 2 CRU has two customer-replaceable LAN logic board subcomponents. Location in OSM Tree: System > SWAN Collection > SWAN > LANLB Example: LAN LB $ZZWAN.#SWAN2.LAN1 Attributes LAN LB $ZZWAN Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts.
Attributes Line $ZZWAN Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Device Name The name of the WAN device associated with the line. Example: $TP6S1 Logical If no device is configured, "FREE" is shown. DLC Task Name The name of the data link control (DLC) task associated with the line. Format: adapter name.clip number.DLC line number Example: $ZZWAN.#D08XE5.1.
Logical MAC Address The media access control (MAC) address of the SWAN Path. IPv4 Address The IPv4 address configured for the SWAN Path. Path State The state of the SWAN Path as known to the operating system. Values: Started, Stopped Actions Start Starts the SWAN Path. When the Start action completes, the SWAN Path is in the Started state. Stop Terminates operation of the SWAN Path. When the Stop action completes, the SWAN Path is in the Stopped state.
System A system is made up of all the hardware components, software, and firmware that are managed by a single operating system. Internal hardware components are housed in enclosures and are arranged in groups, modules, and slots. User-replaceable components are known as customer-replaceable units (CRUs). Components that must be replaced by your service provider are known as field-replaceable units (FRUs). Both CRUs and FRUs can contain subcomponents.
Data Collection Services Automatic Data Collection State Indicates whether automatic data collection for failed system resources is enabled or disabled. To change this attribute state, use the Enable/Disable Automation of Data Collection action. Diagnostic Data Collection Volume Indicates the volume in which automatic or manual data collection will take place. This volume is assigned by using the Set Data Collection Volume action.
OSM also automatically performs periodic checking of these services. Performed every 24 hours by default, the frequency is configurable through an OSMCONF setting. For more information on OSMCONF settings, see the OSM Configuration Guide. Check Storage Dependence on ServerNet Fabric Launches a guided procedure to determine whether system components are dependent upon a particular ServerNet fabric.
NOTE: Generally, new hardware is detected dynamically once it is cabled. This action is only required for recognizing components connected on a port that had been disabled. Enable/Disable Automation of Data Collection Use to enable or disable automatic collection of data for failed system resources. The current state for the system is indicated by the Automatic Data Collection State attribute.
• action, specifying NS16200 or NS14200 as your system type, OSM recognizes the running firmware as appropriate and displays the correct default firmware file names and versions. If you are upgrading (either completely or partially) an existing NS16000 server to NS16200 or an existing NS14000 server to NS14200, because the older blade firmware that was fine for NS16000 and NS14000 does not support the NS16200 or NS14200 (rx 2660) blades.
Rediscover System and Cluster Causes OSM to refresh and reanalyze all components within the system and the ServerNet cluster or NonStop BladeCluster. NOTE: This action is not available for Integrity NonStop NS1000, NS1200, NS2000 series, NS2100, NS2200 series, NS2300, NS2400 series, NS5000, or NS3000AC servers. Reinitialize Complex Manager Reinitializes the Complex Manager Auxiliary Process (CMAP) for each processor in the system.
be changed in the OSMCONF file or extended for an action currently in progress by using the Extend Problem Incident Report Suppression Time action. Performing this action while the system is already in the suppressed state resets the duration of the current suppression to the default time. Synchronize iLO Clocks to NonStop Clock Synchronizes the iLO clock on each Processor Blade (for NonStop BladeSystems) or Blade Element (for NS-Series systems) to the NonStop system's clock.
Related System and Processor-Level Recovery Actions Depending on your system type, these actions may be useful for system and processor recovery operations: • • • Power On System -- this OSM Low-Level Link action can be used to power on the system following power fail scenarios or after using the System Power Off action, provided you are using DNS on your LAN.
NonStop NS-Series • • Fibre Channel tape drives are connected to Fibre Channel ServerNet adapters in IOAM enclosures. SCSI tape drives can be connected to Fibre Channel ServerNet adapters through a Fibre Channel Router (one or two drives per router). Once configured, the Fiber Channel Router object is displayed in the OSM tree pane under the Monitored Service LAN Devices object.
Backup Execution State The state of the backup I/O process. Values: Running, Stopped Backup Process ID The process ID of the backup I/O process. If the state of the backup I/O process is Stopped, this ID is not displayed. Example: 1,285 Controller Path Tape drives connected through an FCSA display these attributes: FSAC Represents the actual presence of the FCSA FSAC containing the backup tape path SCSI controller.
Stop Puts the tape process in a state to disallow regular I/O commands to the tape drive. When the Stop action completes, the tape drive is in the Stopped state. Note that Stop is a logical command and does not affect the hardware. Switch Process Pair Switches processors of the primary and backup tape I/O processes. Test Extended Tests vary depending on the type of tape drive. This table lists the actions performed for each supported tape device (listed by Product ID).
Attributes TRSA Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Hardware Revision A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Manufacturer Identifies the manufacturer of the component. Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts.
Attributes Unknown CRU Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Power State Whether the component is powered on. Values Physical Actions None. UPS Uninterruptible power supply (UPS) unit that provides backup power for Nonstop NS-series enclosures.
Physical Location The values displayed by these attributes are assigned through the Physical Configuration Tool. Rack Name A user-defined name assigned to identify the rack in which the UPS is located. Rack Offset A number (from 1 to 42) assigned to describe the location of the UPS within the rack. Actions Link to Web Interface Launches a browser-based configuration interface for the UPS, which provides additional information and configuration options for the UPS.
Physical Hardware Revision A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. Track ID A unique serial number that identifies the component. Track IDs are used for tracking components. Flash Firmware Information about the version of the operational firmware located in the Flash memory of the FCSA.
VIO G4SA In an Integrity NonStop NS-series system containing VIO enclosures (represented in the OSM Service Connection as VIO modules), OSM displays a G4SA object to represent: • • In slot 6, the Ethernet ports that provide the functional equivalent of a Gigabit 4-port Ethernet adapter. In slot 7, an optional expansion VIO G4SA.
Actions Abort Terminates operation of the VIO G4SA and the associated Ethernet ServerNet addressable controller (SAC). When the Abort action finishes, the VIO G4SA and the SAC are in the Stopped state. Add This action is displayed in OSM only when a VIO G4SA is first inserted and not yet configured. Performing this action ensures that the Configured Type is set to G4SA. Delete Deconfigures the VIO G4SA, removing the associated G4SA SAC and PIF objects.
Physical Hardware Revision A code that identifies the generation of the component. Hardware revision codes are used for tracking components. LED State Indicates whether the VIO logic board LED is on or off. Manufacturer Identifies the manufacturer of the component. Displayed for VIO logic board in S-series VIO modules only. Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts.
Hard Reset Resets the VIO logic board hardware and the routing tables. ME FPGA Update Allows you to update the FPGA code file for the integrated maintenance entity (IME) of the VIO logic board. The firmware file for IME FPGA (SAM0789) is different from that of other MEs.
For more information, see the G16SE Service Provider Supplement for Integrity NonStop BladeSystems. Each VIO Module object, depending on the type of system and configuration, contains: • VIO FCSA in slot 1 -- OSM displays an FCSA object to represent the four built-in Fibre Channel ports that provide the functional equivalent of an FCSA. NOTE: • Valid for NS14000 series, NS1200, and NS1000 servers only. (Optional) Optical Extender PIC in slot 2 for additional processor connectivity (processors 4-7).
Physical Hardware Revision A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. Track ID A unique serial number that identifies the component. Track IDs are used for tracking components. Physical Location The values displayed by these attributes are assigned through the Set Physical Location action.
With T0682 H02 AAN and later, you can also use the Physical Configuration Tool to set the Rack Name and Rack Offset values in a consistent manner throughout the system while you create a physical view of your modular racks. Synchronize FIR Files to Other Switches Synchronizes the FRU information record (FIR) files of the X and Y fabric processor switches. NOTE: This action is only valid from Group 100; it will fail on VIO Modules in NonStop BladeSystem NB54000c and NB56000c or S-series.
Compare State (Other) Value Meaning Same Current and default versions are the same. Up-rev The current version is newer than the default version. Down-rev The current version is older than the default version. Unknown Unable to compare files. Device State Value Meaning Aborting Processing is terminating. AC Power Loss The device is currently not powered by either AC or UPS. Defined State is defined by the NonStop OS. Degraded Performance is degraded.
Group Type A unique number in the system that identifies this group. Group Type is displayed in a window on the front door of the enclosure.
Powered On Meaning Redundant Power Problem There is a problem with the backup power supply for this component (as determined by the Redundant Power Scrub action). Unknown Power state of component is unknown. Processor State Value Meaning Dump in Progress Memory is being dumped from this processor. Submit memory dumps to the your service provider for problem analysis. Executing Diagnostics The processor is performing diagnostics.
Type System NSR-G S70000 NSR-T S72000 NSR-V S74000 NSR-X S76000 NSR-H S78000 NSR-Y S86000 NSR-Z S88000 NSE-A Integrity NonStop NS16000 server NSE-AB Integrity NonStop BladeSystem NB54000 NSE-AD Integrity NonStop NS2200 series server NSE-AE Integrity NonStop NS2100 server NSE-AF Integrity NonStop BladeSystem NB56000 NSE-AG Integrity NonStop NS2300 server NSE-AH Integrity NonStop NS2400 series server NSE-B Integrity NonStop NS1000 server NSE-D Integrity NonStop NS14000 server
Tape Types Product ID Meaning CT9840-1 9840 cartridge tape drive mounted in an L700 tape library CT9840-2 9840 cartridge tape drive mounted in a 9710 tape library CT9840-3 9840 cartridge tape drive mounted on HP NonStop S-series server CT9840-4 9840 cartridge tape drive mounted in a 9310 tape library CT9840FC-1 9840FC (Fibre Channel) cartridge tape drive mounted in an L700 tape library CT9840FC-3 9840FC (Fibre Channel) cartridge tape drive mounted on HP NonStop S-series server CT9840FC-4 9840
Product ID Meaning T5258ACL Super DLT tabletop with ACL T9490 STK 9490 cartridge drive VT5801 Virtual Tape Solution: Tributary Systems Inc. 2U VT5802 Virtual Tape Solution: Tributary Systems Inc. 7U VT5900-A Virtual Tape Solution: Tape Labs Inc. 7U VT5900-B Virtual Tape Solution: Tape Labs Inc. 7U VT5900-C Virtual Tape Solution: Tape Labs Inc. 7U VT5901 Virtual Tape Solution: Tape Labs Inc. 2U VT5902 Virtual Tape Solution: Tape Labs Inc.
12 Managing a ServerNet Cluster A ServerNet cluster is a collection of NonStop servers connected together using the ServerNet protocol. There are two generations of ServerNet clusters that utilize cluster switches for ServerNet cluster connectivity: • The first-generation ServerNet cluster is built around the HP NonStop Cluster Switch (model 6770) and can support up to 24 nodes. It is built using one of the star topologies (star, split-star, or tri-star).
See also Using the Browser’s Find Feature. Monitoring a Cluster ServerNet cluster monitoring tasks include: • Viewing alarms for resources in a ServerNet cluster. This task is similar to viewing alarms for resources within a server, except that you must first select the ServerNet Cluster in the tree pane and then navigate to the cluster resource you want to view. See Viewing a Summary of Alarms. • Viewing attributes for resources in a ServerNet cluster.
Performing actions on ServerNet cluster resources is similar to performing actions on resources within a server. First expand the ServerNet Cluster resource in the tree pane and then navigate to the cluster resource on which you want to perform an action. Specifying a Cluster Switch Locator String The Set Locator action allows you to specify a text string to indicate the physical location of a cluster switch.
1. 2. 3. 4. 5. 6. In the tree pane of the OSM management window, expand the ServerNet Cluster resource and navigate to the Switch component of the Switch Module. Right-click the Switch component and select Attributes. In the Configuration section, check the value of the Compare State attribute. If it is Down-rev, continue with this procedure. Right-click the Switch component and select Actions The Actions dialog box appears.
External Slot Port Internal Router Port 12 1 2 8 2 1 8 3 4 8 4 3 8 1 1 9 2 2 9 3 3 9 4 4 9 13 Router Connections for Router Interconnect PICs External Slot Internal Router Port Slot 4 1 4 2 5 3 4 3 5 1 6 2 4 3 5 4 4 Slot 5 Router Connections in a Layered Topology 265
13 Cluster Resources A ServerNet cluster is built using one of several topologies. The resource objects displayed in the OSM Service Connection for a cluster differ depending on the topology of the ServerNet cluster. ServerNet clusters using one of the star topologies are built with the HP NonStop Cluster Switch (model 6770) and can support up to 24 nodes. ServerNet clusters using the layered topology are built around the HP NonStop ServerNet Switch (model 6780) and can support up to 64 nodes.
Logical Presence Whether the switch is installed and responding. Values: Present, Absent, and Unknown Locator User-assigned text that can be used to help identify the switch. The text is assigned by using the Set Locator action. Example: Switch On Left in 1205 Topology The network topology and ServerNet nodes supported by this 6770 switch. The value is equivalent to the configuration tag of the ServerNet II switch.
Presence Whether the switch module is installed and responding. Values: Present, Absent, and Unknown Track ID The track ID of the switch module midplane. Manufacturer Identifies the manufacturer of the component. Hardware Revision The hardware revision of the switch module midplane. Globally Unique ID A unique, read-only number stored in nonvolatile memory (SEEPROM) on a cluster switch. The Globally Unique ID can be used programmatically to identify the switch.
Set Locator Allows you to enter text to aid in locating or identifying the switch. This text is displayed as the Locator attribute. These ASCII characters cannot be used in the Set Locator field: =, +, &, or %. Also, copy and paste features do not work in this field. For more information, see Specifying a Cluster Switch Locator String. Parameter: Locator – Free-form text up to 64 characters long.
Attributes BladeCluster Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values BladeCluster Service ServerNet Cluster State The current state of the ServerNet Cluster subsystem on the local node. Values: Starting, Started, Stopping, Stopped, and Unknown SCF Equivalent: SCF STATUS SUBSYS $ZZSCL Logical Inter-Zone Distance Indicates whether the distance is Short-Haul or Long-Haul.
ServerNet Path Test on Y Fabric Runs a path test on the Y fabric, checking the local node's connection to the BladeCluster by testing the Y fabric between the local node and remote nodes. Set ServerNet Cluster State Starts or stops the ServerNet Cluster subsystem on the local node. Parameter: ServerNet Cluster State can be set to Stopped or Started.
Attributes Logical Expand Node Number The Expand node number of the local node. Value: 0 through 254 Node Name The Expand name of the local node. Node Position in the Zone The position of the local node in the zone. ServerNet Node Number The ServerNet node number of the local node. X Fabric Connection State The state of the connection from the local node to the remote node over the external ServerNet X fabric.
Y Fabric Connection #2 Port Name Identifies the Y2 port used for BladeCluster connectivity. X Fabric Connection #1 Port Name Identifies the X1 port used for BladeCluster connectivity. X Fabric Connection #2 Port Name Identifies the X2 port used for BladeCluster connectivity. Actions Generate ServerNet Statistics Generates an event containing the ServerNet statistics for the node.
Physical Configuration Tag A parameter used by SCF and the guided procedures that allows SANMAN to select an appropriate switch configuration block (SCB) from the M6770CL switch configuration library. The selected SCB is subsequently loaded on the specified switch. The configuration tag determines the position of the cluster switch in the topology and the ServerNet node numbers supported by the cluster switch.
ServerNet Cluster Service ServerNet Cluster State The current state of the ServerNet Cluster subsystem on the local node. Values: Starting, Started, Stopping, Stopped, and Unknown SCF Equivalent: SCF STATUS SUBSYS $ZZSCL SANMAN Process Pair Primary Execution State The state of the primary SANMAN process. Values: Running, Stopped Primary Process ID The process ID of the primary SANMAN process. If the state of the primary SANMAN process is Stopped, this ID is not displayed.
Switch SANMAN Process Pair Switches the SANMAN process from the primary processor to the backup processor. SCF Equivalent: SCF PRIMARY $ZZSMN Switch SNETMON Process Pair Switches the SNETMON process from the primary processor to the backup processor. SCF Equivalent: SCF PRIMARY $ZZSCL Update Topology Launches an interactive action that guides you in updating the network topology of a ServerNet cluster. You are prompted to temporarily disable dial-out alarms during the update process.
Actions Generate ServerNet Statistics Generates an event containing the ServerNet statistics from the remote node to the local node. ServerNet Remote Node This object represents any system within a ServerNet cluster that is not the local node. Remote nodes are visible when the ServerNet Cluster view is selected.
Line LDEV State The state of the Expand-over-ServerNet line configured from the local node to the selected remote node. Values: Up, Down, Not Available Remote Line LDEV State The state of the Expand-over-ServerNet line configured from the remote node to the local node. Values: Up, Down, Unknown Actions Generate ServerNet Statistics Generates an event containing the ServerNet statistics from the local node to the remote node.
Configuration Configuration Tag A parameter used by SCF and the guided procedures that allows SANMAN to select an appropriate switch configuration block (SCB) from the M6770CL switch configuration library. The selected SCB is subsequently loaded on the specified switch. The configuration tag determines the position of the cluster switch in the topology and the ServerNet node numbers supported by the cluster switch.
Hard Reset Is necessary following a Configuration Update action in order for the changes to take effect. CAUTION: This action disrupts the ServerNet traffic through this switch. SCF Equivalent: SCF RESET SWITCH $ZZSMN, NEAREST { X | Y }, HARD Prepare to Replace Must be performed from each node of a ServerNet cluster before replacing a ServerNet II Switch for SANMAN to accept the new switch. Replace Launches the guided procedure for replacing a ServerNet II Switch.
Actions Blink LED Off Turns off the blinking of the fault LED. Blink LED On Causes the fault LED to start blinking. Switch Group A collection of up to four 6780 switches connected together, typically mounted in a rack, that reside on one fabric of a cluster switch zone. The switch group is identified by a four-digit number. The first two digits (10) distinguish a switch group from a group within a NonStop S-series server.
Physical Hardware Revision The hardware revision of the switch logic board. LED State The state of the fault LED on the switch logic board. Values: On, Off, Blinking Part Number The part number of the switch logic board. Track ID The track ID of the switch logic board. Last Reset Type The reason for last reset operation.
FPGA Version The VPROC of the FPGA (field programmable gate array) image currently loaded on the switch logic board. Default File Name The full path name of the default FPGA file on the server. Default File Version The version of the FPGA image in the default FPGA file. Compare State The differences, if any, between the current and default FPGA versions. Values Actions Blink LED Off Turns off the blinking of the fault LED.
Replace Invokes the Replace Switch Component guided procedure that helps to replace the switch logic board. Soft Reset Soft resets the switch logic board. SCF Equivalent: RESET SWITCH, SOFT Switch PIC A card in the 6780 switch that plugs into the switch logic board. Most switch PICs (except for maintenance PICs and router interconnect PICs) are populated with transceivers that enable connections to the different nodes, layers, and zones of the cluster.
Blink LED On Causes the LEDs to start blinking. Replace Invokes the Replace Switch Component guided procedure that helps to replace the switch PIC. Switch Power Supply A component in the switch modules that converts standard AC line voltage and distributes DC power to all components in the module. Location in OSM tree: External ServerNet Fabric > Switch Group > Switch Module > Switch Power Supply Example: Power Supply (1010.1.
Switch-to-Node PIC A plug-in card (PIC) on the 6770 switch module that connects to a ServerNet node. The last part of the name contains the port number where the PIC is located. Only the PICs in ports 0 through 7 of the switch are used for switch-to-node connections. Location in OSM tree: External ServerNet Fabric > Switch Group > Switch Module > Switch > Switch PIC Example: Switch PIC $ZZSMN.X2.
See also Router Connections for Switch Node Ports. Attributes Switch Node Port Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Transceiver Physical Type The type of transceiver. Example: 9/125 Micron SMF Part Number The vendor part number of the transceiver. Serial Number The vendor serial number of the transceiver. Manufacturer Identifies the manufacturer of the component.
Neighbor ServerNet Node Node Number The ServerNet node number of the neighbor node. Node Name The name of the neighbor node. Actions Node Responsive Test Tests the connectivity on the external ServerNet fabric from the local node to the remote node connected via this port. Switch-to-Switch PIC A plug-in card (PIC) on the 6770 switch module that connects to another switch on the same fabric. The last part of the name contains the port number where the PIC is located.
Switch Port An external transceiver port on a 6780 switch that connects to a 6780 switch in another zone or layer. These ports reside only on switch PICs in slots 2 and 3 (for zone connections) and 11 through 13 (for layer connections). Location in OSM tree: External ServerNet Fabric > Switch Group > Switch Module > Switch PIC > Switch Port Example: Switch Port (1010.1.13.4) See also Router Connections for Ports Connecting to Other Switches.
Transceiver Device State The initial state of the component at the time of discovery. Values: OK, Fault Transceiver Enabled State Whether the transceiver is enabled. Enabled: The component is operational. Disabled: The component is present but not operational. Neighbor Switch Port Switch Port The name of the port to which this port is connected. Format: Port (Group.Module.Slot.Port) where: Group can be 1010, 1020, 1030, 1011, 1021 or 1031. Module can be 1, 2, 3 or 4. Slot can be 2, 3, 11, 12 or 13.
Actions Replace Launches the Replace Switch Component guided procedure, which provides help for replacing the component. Common Attribute Values Service State This attribute appears in the list of attributes only when attention or service is required. Value Meaning OK The object is functioning properly. This value appears only in the Problem Summary dialog box. Attention Required The resource requires operator attention.
Port Connectivity Status Value Valid Only For Reset Link dead (Loss of optical signal) Link dead (Transceiver absent) No link alive Link alive, port disabled Link alive, port disabled, neighbor check in progress Link alive, port disabled, neighbor check complete Link alive, port disabled, neighbor check failed (Not Zone-to-Zone Interconnect and Layer-to-Layer Interconnect ports connected) Link alive, port disabled, neighbor check failed (Connected to switch) Switch-to-Node Interconnect ports Link alive,
14 Updating ServerNet Cluster Topology You can update a ServerNet cluster to support more nodes or to expand the geographical limits of the cluster. These topics provide guidance on the different types of topology updates: • • To locate relevant information for your update, see Identifying Your Update Type. If you need to add a node to a cluster without changing the topology, log on to the node using OSM, and perform the Add Node to ServerNet Cluster action.
NOTE: Do not use this procedure unless you have the OSM package running on all nodes of the cluster. Instead, use the TSM Add Switch guided procedure as described in the ServerNet Cluster Manual to perform the update. If you use the TSM Add Switch procedure, and the OSM package is running on any nodes in the cluster, be sure the OSM Notification Director is not configured to dial out alarms.
9. 10. 11. 12. 13. 14. 15. 16. Disconnect any existing X-fabric cables between the cluster switches. (If you are updating from a star topology, there are no existing cables between switches.) Connect all the cables between the X-fabric switches to support the new topology. The new switch port connections will differ from the original cluster. See Cable Connections Between Star Groups. For more information on connecting cables refer to the ServerNet Cluster Manual.
Cable Connections Between Star Groups Updating to the Split-Star Topology If you are updating to the split-star topology, connect the cables as follows: Cluster Switch Port Connects to Cluster Switch Port X1 8 X2 8 X1 9 X2 9 X1 10 X2 10 X1 11 X2 11 Y1 8 Y2 8 Y1 9 Y2 9 Y1 10 Y2 10 Y1 11 Y2 11 Updating to the Tri-Star Topology If you are updating to the tri-star topology, connect the cables as follows: Cluster Switch Port Connects to Cluster Switch Port X1 8 X2 10 X
Switch PIC Slot Port Connect to Switch PIC Slot Port X11/Y11 11 4 X12/Y12 11 4 X11/Y11 12 1 X13/Y13 12 1 X11/Y11 12 2 X13/Y13 12 2 X11/Y11 12 3 X13/Y13 12 3 X11/Y11 12 4 X13/Y13 12 4 X11/Y11 13 1 X14/Y14 13 1 X11/Y11 13 2 X14/Y14 13 2 X11/Y11 13 3 X14/Y14 13 3 X11/Y11 13 4 X14/Y14 13 4 X12/Y12 12 1 X14/Y14 12 1 X12/Y12 12 2 X14/Y14 12 2 X12/Y12 12 3 X14/Y14 12 3 X12/Y12 12 4 X14/Y14 12 4 X12/Y12 13 1 X13/Y13 13 1 X12/Y
Switch PIC Slot Port Connect to Switch PIC Slot Port X14 2 1 X24 2 2 X14 2 2 X24 2 1 X14 3 1 X24 3 2 X14 3 2 X24 3 1 Y Fabric Connections Between Two Zones This table lists the Y-fabric connections between two zones of a layered topology: Switch PIC Slot Port Connect to Switch PIC Slot Port Y11 2 1 Y21 2 2 Y11 2 2 Y21 2 1 Y11 3 1 Y21 3 2 Y11 3 2 Y21 3 1 Y12 2 1 Y22 2 2 Y12 2 2 Y22 2 1 Y12 3 1 Y22 3 2 Y12 3 2 Y22 3 1 Y13 2
Switch PIC Slot Port Connect to Switch PIC Slot Port X13 2 1 X23 2 2 X13 2 2 X33 2 1 X13 3 1 X23 3 2 X13 3 2 X33 3 1 X14 2 1 X24 2 2 X14 2 2 X34 2 1 X14 3 1 X24 3 2 X14 3 2 X34 3 1 X21 2 1 X31 2 2 X21 3 1 X31 3 2 X22 2 1 X32 2 2 X22 3 1 X32 3 2 X23 2 1 X33 2 2 X23 3 1 X33 3 2 X24 2 1 X34 2 2 X24 3 1 X34 3 2 Y Fabric Connections for Three Zones This table lists the Y-fabric connections for three zones of a l
Switch PIC Slot Port Connect to Switch PIC Slot Port Y21 3 1 Y31 3 2 Y22 2 1 Y32 2 2 Y22 3 1 Y32 3 2 Y23 2 1 Y33 2 2 Y23 3 1 Y33 3 2 Y24 2 1 Y34 2 2 Y24 3 1 Y34 3 2 302 Updating ServerNet Cluster Topology
Glossary A|B|C|D|E|F|G|H|I|J|K|L|M|N|O|P|Q|R|S|T|U| V|W|X|Y|Z A AC transfer switch A component of a NonStop™ Cluster Switch (model 6770) that provides access to dual AC power sources and the ability to switch between the two sources if one fails. The AC transfer switch draws power from its primary power source as long as it is available. If the primary source fails, the AC transfer switch is switched to draw power from the secondary power source.
backup processor A processor running the HP NonStop™ operating system that communicates with the primary processor, allowing the processors to remain independent. A component failure in one processor has no effect on any other processor. Baseboard Management Controller (BMC) firmware The firmware for the baseboard management controller (BMC) that monitors environmental sense and control data. Blade Element A portion of one or more logical processors and one part of a Blade Complex.
See also cluster switch group. cluster switch logic board A circuit board that provides switching logic for HP NonStop™ ServerNet Switch (model 6780). The logic board (LB) has a front panel for operator and maintenance functions. cluster switch zone A pair of X-fabric and Y-fabric cluster switch groups and the ServerNet nodes connected to them. Up to three zones are possible.
disk drive A device that stores data on a disk and provides random access to addressable locations on the disk. There are two types of disk drives: • On magnetic drives, access is provided by magnetic read/write heads. • On optical drives, access is provided by a low-intensity laser beam. disk volume A logical disk drive. A volume can be one or two physical drives. In NonStop servers, volumes have names that begin with a dollar sign ($), such as $DATA.
Fast Ethernet ServerNet adapter (FESA) A single-ported ServerNet adapter that supports 100-megabit/second (Mbps) or 10-Mbps Ethernet data transfer rates on an HP NonStop S-series server. Fiber-optic ServerNet cable A ServerNet cable that uses fiber optics to transmit data. HP NonStop™ servers support two types of fiber-optic ServerNet cables: multi-mode fiber-optic (MMF) ServerNet cable and single-mode fiber-optic (SMF) ServerNet cable.
H halt To stop a processor, terminating all processes running in it. Halt is a processor action available in both the OSM Low-Level Link and the OSM Service Connection. Halting a processor does not affect any other processors in the system. An error situation that stops a processor, terminating all processes running in it. If a processor halts on its own, OSM issues an alarm such as Processor Software Halt.
See also light-emitting diode (LED). initial discovery Discovery of a NonStop server with which the or the OSM Service Connection has had no prior contact and for which it has no locally saved information. See also discovery. internal ServerNet fabrics The fabrics that link ServerNet devices within an HP NonStop™ server. See also external ServerNet fabrics. internal ServerNet X or Y fabric The fabrics that link ServerNet devices within an HP NonStop™ server. See also fabric.
logical interface (LIF) A process that allows an application or another process to communicate with data communications hardware. logical name An attribute of a resource that is either assigned to the I/O process associated with the resource during configuration using the Subsystem Control Facility (SCF) or that represents the type of resource or its location. When you are logged on to the OSM Service Connection, you can use the logical name to locate a resource.
and system-load control. The OSM system console communicates directly with the MSPs on the server. The enclosure containing processors 0 and 1 contains the MSP pair. media access control (MAC) address A value in the medium access control sublayer of the IEEE/ISO/ANSI local area network (LAN) architecture that uniquely identifies an individual station implementing a single point of physical attachment to a LAN.
network Two or more computer systems (nodes) connected so that they can exchange information and share resources. See also local area network (LAN), ServerNet system area network (ServerNet SAN), wide area network (WAN). node A uniquely identified computer system connected to one or more other computer systems in a network. For example, each server in a ServerNet cluster, an Expand network, and a FOX ring is a node.
physical interface (PIF) The hardware components that connect a system node to a network. physical location A three-part identifier that specifies the group number, module number, and slot number of a resource. For example: GRP-2.MOD-1.SLOT-8. Physical view One of several views available in the view pane of the Management window. The Physical view of a server is a view of all the enclosures and is intended to represent the actual floor plan at the site.
processor element (PE) A single microprocessor or microprocessor core, with its associated memory, capable of executing a single instruction stream. processor switch A self-contained, rack-mountable FRU that provides connectivity for processors and I/O in an HP NonStop NS-series server. The processor switch includes the chassis, power supplies, fans, ServerNet switch board, ServerNet plug-in cards (PICs), maintenance PIC, and crosslink PIC.
SCSI ServerNet addressable controller (S-SAC) A ServerNet addressable controller (SAC) that is contained within a small computer system interface (SCSI) plug-in card (S-PIC). serial copper plug-in card (PIC) A plug-in card (PIC) for the modular ServerNet expansion board (MSEB) and I/O multifunction (IOMF) 2 customer-replaceable unit (CRU) that supports the serial copper interface. serial ZX1 I/O link The cable that connects the LSU and the processor element.
service connection A connection between the system console and the OSM software on a NonStop server. A service connection is initiated from the browser on the system console and can be used to communicate with the server only when the NonStop operating system is running. The OSM Service Connection provides a comprehensive service and maintenance picture of the server or ServerNet cluster and is used to perform most service management tasks. See also low-level link (LLL).
See also star topology, tri-star topology, layered topology. status/console message A message that keeps the user informed about the status of the requested action. subnetwork A physical network within an internet protocol (IP) network. Each IP network can be divided into a number of subnetworks. Within a given network, each subnetwork is treated as a separate network. Outside that network, the subnetworks appear as part of a single network. The terms subnetwork and subnet are used interchangeably.
tetrahedral topology A topology of NonStop S-series servers in which the ServerNet connections between the processor enclosures form a tetrahedron. tetrahedron A solid bounded by four triangular faces. In ServerNet context, a tetrahedron is four processors interconnected by ServerNet links so as to form a conceptual tetrahedron. Each processor therefore has a direct connection to the other three processors. See also tetrahedral topology.
• • Support for dial-in on a system console Recommended repair actions associated with alarms vertical tetrahedron A topology of NonStop S-series servers in which the ServerNet connections between the layers of a cluster switch group form a tetrahedron See also tetrahedron, tetrahedral topology, cluster switch layer. view One of several representations of the server or ServerNet cluster that appear in the view pane of the Management window. See also Inventory view, Physical view.
Index Symbols 4PSE, 86 actions, 86 attributes, 86 6770 Switch Module about, 267 actions, 268 attributes, 267 6780 Switch Module about, 268 actions, 269 attributes, 268 A AC Transfer Switch about, 270 actions, 270 attributes, 270 Access Control List, 73 actions automatically initiating, 75 controlling access, 73 detailed information about, 75 on multiple resources, 76 performing, 73 performing on a resource, 75 saving details, 78 stopping, 75 summary of, 81 viewing details, 78 Add Node to ServerNet Cluster,
Cluster about, 275 actions, 276 attributes, 275 cluster resources list of, 267 locating, 261 managing, 267 monitoring, 262 performing actions on, 262 viewing, 261 cluster switch specifying location, 263 cluster topology updating, 295 CMAP, reinitialize, 237 Collect CLIM Logs, 109 Collect CLIM Logs action, 107 Collect Diagnostic Data, 234 Common Communication ServerNet Adapter (see CCSA CRU) Compare HSS Firmware Versions, 234 Configuration Update, 280, 284 Configure CLIM action, 109 Copy Core License to Alte
actions, 151 attributes, 151 FESA about, 151 actions, 152 attributes, 152 Fiber, 153 Fiber ServerNet Addressable Controller (see FSAC) Fibre Channel Router about, 153 actions, 154 attributes, 153 firmware updating, 83 Firmware update Switch Logic Board, 284 firmware updates performing, 78 FPGA code update Switch Logic Board, 284 FSAC, 122 about, 154 actions, 155 attributes, 154 G G4SA about, 155 actions, 156 attributes, 155 G4SA PIF about, 156 actions, 157 attributes, 156 G4SA SAC about, 157 actions, 159 a
managing a system, 83 Memory Card about, 175 Module about, 176 actions, 177 attributes, 176 Monitored Service LAN Devices about, 178 actions, 178 Motherboard, 179 N NIC, 179 Node Connectivity ServerNet Path Test, 272 Node Responsive Test, 287, 289 O Optical Extender PIC, 180 actions, 181 attributes, 180 P PCI Riser, 181 PE Blade Element Track ID, 199 PE LID, 199 PE Memory Size, 199 PE Reintegration Enable State, 200 PE State, 200 PE Stop Code, 200 Perform Data Sanitization, 236 Physical Configuration Too
Replace, 270, 281, 285, 286, 292 Replacement Part Number, 200 Reset ServerNet Statistics, 271 Reset Statistics, 276 Responsive Test, 155 Restore CLIM Configuration action, 108 S SAC about, 204 actions, 206 attributes, 205 sanitize disk, 236 SAS Card about, 206 SAS Disk, 125 SCSI Controller about, 209 actions, 210 attributes, 209 SCSI Extender, 222 SCSI SAC (see SSAC) SCSI-to-Fiber Converter, 222 ServerNet cluster, 275 cluster actions, 276 cluster attributes, 275 external fabric, 272 internal fabric, 164, 1
about, 281 actions, 282 attributes, 281 Switch Group about, 282 Switch Logic Board about, 282 actions, 284 attributes, 282 Switch Node Port about, 287 actions, 289 attributes, 288 Switch PIC about, 285 actions, 285 attributes, 285 Switch Port about, 290 attributes, 290 Switch Power Supply about, 286 actions, 286 attributes, 286 Switch SANMAN Process Pair, 277 Switch SNETMON Process Pair, 277 Switch-to-Node PIC about, 287 attributes, 287 Switch-to-Switch PIC about, 289 attributes, 289 Synchronize iLO Clocks
Y Fabric ServerNet State , 172 327
