HP Virtual Connect Enterprise Manager 6.3.1 CLI Guide
Table Of Contents
- HP Insight Software Virtual Connect Enterprise Manager
- Contents
- 1 Getting Started
- 2 Using VCEMCLI
- 3 Using VCEM commands
- add profile
- set profile
- assign profile
- export profiles
- unassign profile
- add enet-connection
- set enet-connection
- remove enet-connection
- add fc-connection
- set fc-connection
- remove fc-connection
- add fcoe-connection
- set fcoe-connection
- remove fcoe-connection
- add iscsi-connection
- set iscsi-connection
- remove iscsi-connection
- set iscsi-boot-param
- remove iscsi-boot-param
- add server-port-map
- set server-port-map
- remove server-port-map
- poweroff devicebay
- poweron devicebay
- show power-status
- show job
- show version
- show vcem-status
- startvcdmaint
- cancelvcdmaint
- completevcdmaint
- 4 Error messages
- 5 Troubleshooting VCEMCLI
- VCEMCLI calls result in access denied errors
- VCEMCLI calls result in errors for invalid leading character or invalid characters
- VCEMCLI calls result in 404 errors
- API timeouts
- High CPU usage on the CMS server while running a VCEMCLI client
- Job reports failed status
- Completed with warning job status
- Unable to assign a profile to a Domain Group
- VC Domain reports Configuration Mismatch status
- VC Domain reports Expired License status
- Error on database operation occurs
- Failed to execute VCEM operation because VC firmware not supported
- Creating a server profile fails
- Server profile edit operation fails when target server is powered on
- Server profile job completed with success but changes have not occurred
- After a server profile assignment, some connections defined in the server profile are not functional
- Commands -add profile or -set profile error messages
- Command -add profile error messages
- Additional Troubleshooting Information and tools
- 6 Support and other resources
- Index
Table 22 Parameter descriptions for -set iscsi-boot-param (continued)
OptionalRequiredDescriptionParameter
x
NOTE: The
-targetport2 parameter
is required if the
-targetip2 parameter is
specified.
The TCP port associated with
the alternate target IP
address. The default value is
3260.
-targetport2
xThe initiator and target must
agree on an authentication
-authentication
method or the iSCSI initiator
cannot log on to the target.
Supported Authentication
values include none, chap
and chapm. The default
selection for this attribute is
none.
x
NOTE: The -username
parameter is required if the
authentication type is chap
or chapm.
User name for
authentication. The
username length is a
maximum of 223 characters.
If the name string contains
non-alphanumeric
-username
characters, it should be
enclosed in quotes.
x
NOTE: The -secret
parameter is required if the
authentication type is chap
or chapm.
Secret password for chap
and authentication. It is
specified as a string or a
long hex value (starting with
'0x'). This value must be at
least 96 bits (12 bytes, 24
-secret
hex digits) and at most 16
bytes, 32
x
NOTE: The
-mutualusername
parameter is required if the
authentication type is
chapm.
User name for
authentication. The
username length is a
maximum of 223 characters.
If the name string contains
non-alphanumeric
characters, it should be
enclosed in quotes.
-mutualusername
x
NOTE: The
-mutualsecret parameter
is required if the
authentication type is
chapm.
Password for authentication.
It should be specified as a
string or a long hexadecimal
value (starting with 0x). This
value must be at least 96
bits (12 bytes, 24
hexadecimal digits) and at
-mutualsecret
most 16 bytes, 32
hexadecimal digits long.
xAllows the iSCSI option
ROM to retrieve the iSCSI
-iscsibootparamdhcp
boot parameters from DHCP
or through static
configuration. Valid values
are enabled and
disabled. The default
selection for this attribute is
disabled allowing for
static configuration.
48 Using VCEM commands