HP Virtual Connect Enterprise Manager 6.3.1 CLI Guide
Table Of Contents
- HP Insight Software Virtual Connect Enterprise Manager
- Contents
- 1 Getting Started
- 2 Using VCEMCLI
- 3 Using VCEM commands
- add profile
- set profile
- assign profile
- export profiles
- unassign profile
- add enet-connection
- set enet-connection
- remove enet-connection
- add fc-connection
- set fc-connection
- remove fc-connection
- add fcoe-connection
- set fcoe-connection
- remove fcoe-connection
- add iscsi-connection
- set iscsi-connection
- remove iscsi-connection
- set iscsi-boot-param
- remove iscsi-boot-param
- add server-port-map
- set server-port-map
- remove server-port-map
- poweroff devicebay
- poweron devicebay
- show power-status
- show job
- show version
- show vcem-status
- startvcdmaint
- cancelvcdmaint
- completevcdmaint
- 4 Error messages
- 5 Troubleshooting VCEMCLI
- VCEMCLI calls result in access denied errors
- VCEMCLI calls result in errors for invalid leading character or invalid characters
- VCEMCLI calls result in 404 errors
- API timeouts
- High CPU usage on the CMS server while running a VCEMCLI client
- Job reports failed status
- Completed with warning job status
- Unable to assign a profile to a Domain Group
- VC Domain reports Configuration Mismatch status
- VC Domain reports Expired License status
- Error on database operation occurs
- Failed to execute VCEM operation because VC firmware not supported
- Creating a server profile fails
- Server profile edit operation fails when target server is powered on
- Server profile job completed with success but changes have not occurred
- After a server profile assignment, some connections defined in the server profile are not functional
- Commands -add profile or -set profile error messages
- Command -add profile error messages
- Additional Troubleshooting Information and tools
- 6 Support and other resources
- Index
set iscsi-boot-param
The -set iscsi-boot-param command configures the basic iSCSI boot parameters on the
specified iSCSI connection.
Syntax
-set iscsi-boot-param
–profilename <profileName>
-portnumber <PortNumber>
-bootorder <Primary|Secondary|Disabled|USEBIOS>
[-lun <Logical Unit number>]
[-initiatorname <Initiator name>]
[-initiatorip <IP address>]
[-mask <Netmask>]
[-gateway <Gateway>]
[-vlanid <Vlan Id>]
[-targetname <Target Name>]
[-targetip <Primary Target IP>]
[-targetport <Primary Target Port>]
[-targetip2 <Alternate Target IP>]
[-targetport2 <Alternate Target Port>]
[-authentication <None|CHAP|CHAPM>]
[-username <username>]
[-secret <secret password>]
[-mutualusername <username>]
[-mutualsecret <Mutual secret password>]
[-iscsibootparamdhcp <enabled|disabled>]
[-networkparamdhcp <enabled|disabled>]
[-dhcpvendorid <VendorID>]
Parameters
Table 22 Parameter descriptions for -set iscsi-boot-param
OptionalRequiredDescriptionParameter
xThe name of the profile
associated with the
iscsi-boot-param.
-profilename
xThe number of the port for
this set of parameters.
-portnumber
xEnables or disables iSCSI
boot. Selecting primary,
-bootorder
secondary or usebios
will result in the iSCSI boot
being enabled. The default
selection for this attribute is
disabled.
xThe Logical Unit Number
(LUN) of the Target identifies
-lun
the volume to be accessed.
Valid values for standard
LUNs are 0-255 decimal.
Valid values for extended
LUNs are 13 to 16 character
hexadecimal values. The
default value is zero.
46 Using VCEM commands