HP Imaging and Printing Security Center Installation and Setup Guide
HP Imaging and Printing Security Center Installation and Setup Guide
Copyright information © 2012 Copyright Hewlett-Packard Development Company, L.P. Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under the copyright laws. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Table of contents 1 Introduction ..................................................................................................................................................... 1 System requirements ........................................................................................................................... 2 Installation overview .............................................................................................................................
iv ENWW
1 Introduction The HP Imaging and Printing Security Center is a security compliance tool. Use it to create policies to assess the security of your imaging and printing devices, configure the devices to comply with the policy, and monitor the devices for continued compliance. Use this guide to install and set up the HP Imaging and Printing Security Center.
System requirements The following lists the basic requirements for installing the HP Imaging and Printing Security Center: ● Approximately 30 megabytes of free disk space to install the HP Imaging and Printing Security Center. ● Approximately 4 gigabytes of free disk space to install the HP Imaging and Printing Security Center database. ● Microsoft SQL Server 2005 or newer. (The HP Imaging and Printing Security Center can install Microsoft SQL Server 2008 R2 Express.
Installation overview Using the HP Imaging and Printing Security Center installation, you can install the service, user interface, and database on a single computer, install the database remotely, or install the user interface so it can remotely connect to the service. The HP Imaging and Printing Security Center can use your existing installation of Microsoft SQL Server, or install Microsoft SQL Server 2008 R2 Express if needed.
Verify Administrator account requirements Review the following information before you begin the HP Imaging and Printing Security Center installation. 4 ● You must log on as the Administrator, or use an account that is a member of the Administrators group, on the local computer. The account must have the proper privileges to connect to the HP Imaging and Printing Security Center database.
Install the prerequisite software Before installing the HP Imaging and Printing Security Center, you must have the following software installed on the computer(s) where the system will run. NOTE: If required, the HP Imaging and Printing Security Center installation program (HPIPSC_Setup.exe) will install these products during the installation. ● Microsoft .NET Framework 3.
Install Microsoft .NET Framework 3.5 SP1 on Windows Server 2008 R2 The HP Imaging and Printing Security Center requires Microsoft .NET Framework 3.5 Service Pack 1. The HP Imaging and Printing Security Center installation program (HPIPSC_Setup.exe) will attempt to install the package if it is not found on the computer. However, Windows Server 2008 R2 does not allow installation of Microsoft .NET 3.5 SP1.
2 Install, configure, or uninstall the HP Imaging and Printing Security Center Use the following sections to install, configure, or uninstall the HP Imaging and Printing Security Center.
Install the HP Imaging and Printing Security Center system Use the appropriate section, depending on how you are installing the HP Imaging and Printing Security Center. ● Install the user interface, service, and database on the same computer on page 8 — Instructions for installing the HP Imaging and Printing Security Center user interface, service, and database on the same computer.
4. Review and click the I accept the terms of the license agreement button to accept the license agreement, and then click Next. 5. For Setup Type, select Full Install and then click Next. 6. For Choose Destination Location, click Next to use the default as shown, or click Browse to select an alternative folder. Then click Next. 7. For Database Location: a. Select the Install SQL Server Express 2008 R2 button to install Microsoft SQL Server 2008 R2 Express on this computer. b.
9. If you selected Use a local database server, use the Select Database Server to select the database server from the list, or click Browse to search for one, and then click Next. If you enter the database server, use the format \. For example: MyComputer\SQLExpress NOTE: If the installation wizard cannot connect to the database (an error is displayed), verify that the account you used to install the service has database connection privileges. 10.
computer so that it can access the HP Imaging and Printing Security Center service. The following figure shows the installation on computer A. Figure 2-2 Install a remote user interface Use the following steps to install the HP Imaging and Printing Security Center remote user interface: 1. Verify that you have completed a full installation (user interface, service, and database) of the HP Imaging and Printing Security Center.
7. For Setup Type, select User Interface Only, and then click Next. 8. For Choose Destination Location, click Next to use the default as shown, or click Browse to select an alternative folder and then click Next. 9. Click Install to start the installation. To go back and modify your selections, click Back. To discard your selections and quit, click Cancel.
system, and then complete a full installation of the HP Imaging and Printing Security Center. The following figure shows the installation. Figure 2-3 User interface and service on computer A — Database on computer B Use the following steps to install the HP Imaging and Printing Security Center: 1. Log on to the computer where the HP Imaging and Printing Security Center database will run (computer B in the figure). 2. Install and configure the Microsoft SQL Server on this computer, if required.
6. For Setup Type, select Database Only and then click Next. 7. For Select Database Server, click Browse to locate the Microsoft SQL server, select it, and then click Next. 8. Use the section Configure remote database security on page 18 and complete the procedure to allow access by the HP Imaging and Printing Security Center service. Once you have completed the changes, continue with the next step to install the user interface and service. 9.
14. For Choose Destination Location, click Next to use the default as shown, or click Browse to select an alternative folder and then click Next. 15. For Database Location, select Use a Remote database server, and then click Next. 16. For Select Database Server, type the database server to install, or click Browse to search for one, and then click Next. (This is the database server instance that you installed in step 2.
Configure remote access to the HP Imaging and Printing Security Center service You must configure the HP Imaging and Printing Security Center service to allow user access from a remote computer. By default, the service allows remote access to all users who are members of the local Administrators group on the machine on which the HP Imaging and Printing Security Center service runs.
Configure database security for Microsoft SQL Server 2012 If you use Microsoft SQL Server 2012 or SQL Server 2012 Express locally or remotely, you must configure the database to allow access by the HP Imaging and Printing Security Center service. The HP Imaging and Printing Security Center service runs as NT AUTHORITY/NETWORK SERVICE.
Configure remote database security If the database was installed remotely from the HP Imaging and Printing Security Center service , you must configure the database to allow access by the service. The HP Imaging and Printing Security Center service runs as NT AUTHORITY/NETWORK SERVICE. When the service accesses the HP Imaging and Printing Security Center database across the network, it uses the service computer’s credentials, which is an account named \$.
Uninstall the HP Imaging and Printing Security Center system Use the appropriate section to uninstall the HP Imaging and Printing Security Center system. NOTE: It is not necessary to stop the HP Imaging and Printing Security Center service before running the uninstall program. The service is stopped as part of the process.
Uninstall a remote user interface from one computer Use the following steps to uninstall the HP Imaging and Printing Security Center user interface when it was installed on a remote computer. 1. Log on to the computer where the HP Imaging and Printing Security Center user interface was installed (computer A in the figure). 2. Click Start and then click Control Panel. 3. Click Add or Remove Programs or Programs and Features, depending on the operating system you use. 4.
5. Indicate whether or not to remove the license file when asked Do you want to remove the license file? 6. Log on to the computer where the HP Imaging and Printing Security Center database was installed (computer B in the figure). 7. Click Start and then click Control Panel. 8. Click Add or Remove Programs or Programs and Features, depending on the operating system you use. CAUTION: The uninstall program permanently removes the HP Imaging and Printing Security Center information from the database.
22 Chapter 2 Install, configure, or uninstall the HP Imaging and Printing Security Center ENWW
3 Solve problems Use this section to solve typical installation problems. The following error is displayed when attempting to start the HP Imaging and Printing Security Center user interface: Authorization failed. You do not have access to this system. Cause Solution This will typically happen if the user runs the HP Imaging and Printing Security Center user interface from a remote computer.
Attempts to start HP Imaging and Printing Security Center user interface result in error messages about the Service Not Running. Cause Solution The HP Imaging and Printing Security Center service might not be running. Log on to the computer that runs the HP Imaging and Printing Security Center service. Click Start, then click Control Panel. From the Administrative Tools folder, double click Services.
A Software license agreement HEWLETT-PACKARD SOFTWARE LICENSE TERMS The following License Terms govern your use of the accompanying Software unless you have a separate signed agreement with HP. License Grant. HP grants you a license to Use multiple copies of the Software. "Use" means storing, loading, installing, executing or displaying the Software. You may not modify the Software or disable any licensing or control features of the Software.
DISCLAIMER: TO THE EXTENT ALLOWED BY LOCAL LAW, THIS SOFTWARE IS PROVIDED TO YOU "AS IS" WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. HP SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, SATISFACTORY QUALITY, NON-INFRINGEMENT AND FITNESS FOR A PARTICULAR PURPOSE. Some countries/regions, states and provinces do not allow exclusion of implied warranties or conditions, so certain exclusions may not apply to you.
© 2012 Hewlett-Packard Development Company, L.P. www.hp.
