Manualshelf

HP XP P9000 RAID Manager Reference Guide (T1610-96061, January 2014)

ManualsBrandsHP ManualsStorageHP XP P9500 Disk Array
81828384858687888990
B=D: Comparing for CHK-F2 in the data block is disabled.
Z =E: The NON zero checking for CHK-F2 in the data block is enabled.
D: The NON zero checking for CHK-F2 in the data block is disabled.
SR-W-B-S: Displays the flags for checking regarding CHK-F1 in the data block.
R =E: Checking for CHK-F1 on Read is enabled.
D: Checking for CHK-F1 on Read is disabled.
W =E: Checking for CHK-F1 on Write is enabled.
D: Checking for CHK-F1 on Write is disabled.
B =E: Checking for CHK-F1 in the data block #0 is enabled.
D: Checking for CHK-F1 in the data block #0 is disabled.
S =E: Referring for CHK-F1 flag contained in the data block is enabled.
D: Referring for CHK-F1 flag contained in the data block is disabled.
Example 2
Example of raidvchkscan command with -v offset option
# raidvchkscan -p CL1-A -v offset
PORT# /ALPA/C TID# LU# Seq# Num LDEV# Bsize STLBA ENLBA
BNM
CL1-A / ef/ 0 0 0 2332 1 0 1024 1 102400
9
CL1-A / ef/ 0 0 1 2332 1 1 1024 1 102400
9
CL1-A / ef/ 0 0 2 2332 1 2 1024 1 102400
9
CL1-A / ef/ 0 0 3 2332 1 3 1024 1 102400
9
CL1-A / ef/ 0 0 4 2332 1 4 1024 1 102400
9
Output of the raidvchkscan command with -v offset option:
Bsize: Displays the data block size of Oracle I/O, in units of bytes.
STLBA: Displays the Start of LBA on a target volume for checking, in units of 512 bytes.
ENLBA: Displays the End of LBA on a target volume for checking, in units of 512 bytes.
Note:
If STLBA and ENLBA are both zero, this means to check all blocks.
BNM: Displays the number of bits for checking regarding CHK-F2, in units of bits. If BNM is zero,
this means the checking for CHK-F2 is disabled.
Example 3
Example of raidvchkscan command with -v errcnt option
# raidvchkscan -p CL1-A -v errcnt
PORT# /ALPA/C TID# LU# Seq# Num LDEV# CfEC MNEC SCEC
BNEC
CL1-A / ef/ 0 0 0 2332 1 0 0 0 0
0
CL1-A / ef/ 0 0 1 2332 1 1 0 0 0
0
CL1-A / ef/ 0 0 2 2332 1 2 0 0 0
0
CL1-A / ef/ 0 0 3 2332 1 3 0 0 0
0
CL1-A / ef/ 0 0 4 2332 1 4 0 0 0
0
Output of the raidvchkscan command with -v errcnt option:
CfEC: Displays the error counter for checking of block size validation.
MNEC: Displays the error counter for checking of CHK-F3 validation.
88 Data management commands