HP XP P9000 RAID Manager Reference Guide (T1610-96061, January 2014)

Note: This command is rejected with EX_ERPERM by connectivity checking between RAID Manager
and the RAID storage system.
Syntax
raidvchkscan { -h | -q | -z | -I[H][M][instance#] or
I[TC][SI][instance#] | -p <port> [hgrp] | -pd[g] <raw_device>
| -s <seq#> | -t <target> | -l <lun> | [ -f[x] ] | -v <op> }
Options and parameters
DescriptionOption
Displays Help/Usage and version information.-h
Terminates the interactive mode and exits the command.-q
Makes the raidvchkscan command enter the interactive mode. The -zx option guards performing
of the HORCM in the interactive mode. When this option detects a HORCM shut down, interactive
mode terminates.
-z or -zx
OpenVMS cannot use the -zx option.
Specifies the command as [HORC]/[HOMRCF] or [Continuous Access Synchronous]/[Business
Copy], and used when specifying the RAID Manager instance number.
-I[H][M] [instance#]
or
-I[TC][SI] [instance#]
Specifies the port ID of the port to be scanned. Valid ports are CL1-A to CL1-R and CL2-A to
CL2-R (excluding CL1-I, CL1-O, CL2-I, CL2-O). In addition, it will be able to specify from CL3-a
to CL3-r (except CL3-i, CL3-o), or CL4-a to CL4-r (except CL4-i, CL4-o) for the expanded port.
-p <port> [hgrp]
The port is not case sensitive (for example, CL1-A= cl1-a= CL1-a= cl1-A, CL3-a= CL3-A= cl3-a=
cl3-A). This option must be specified if '-find' or '-pd <raw_device>'option is not specified.
Specify [hgrp] to display only the LDEVs mapped to a host group on a port.
Specifies the raw device name. This option finds Seq# and port_name of the storage system to
which the specified device can be connected, and scans the port of the storage system which
-pd[g]
<raw_device>
corresponds with the unit ID that searches the unit ID from Seq#. This option must be specified if
the '-find' option is not specified. If this option is specified, the following -s <Seq#> option is
invalid.
-pdg (XP1024/XP128 Disk Array and later): Shows a LUN on the host view by finding a host
group.
Used to specify the Seq# (serial#) of the storage system when this option cannot specify the unit
ID which is contained for '-p <port>' option. This option scans the port specified by '-p <port>'
-s <Seq#>
option of the storage system which corresponds with the unit ID that searches the unit ID from
Seq#. If this option is specified, then the unit ID which is contained in '-p <port>' option is invalid.
Specifies a target ID (0 to 15) of the specified port. If this option is not specified, the command
applies to all target IDs.
-t <target>
Specifies a LUN (0 to 7) of the specified target ID. If this option is not specified, the command
applies to all LUNs. If this option is specified, the TID must also be specified.
-l <lun>
Displays the LDEV/STLBA/ENLBA number in hexadecimal notation.-fx
Specifies the following operation that displays each parameter for validation checking:-v [op]
cflag: Displays all flags for checking regarding data block validation for target vols.
offset: Displays the range setting for data block size of Oracle I/O and a region on a target
volume for validation checking.
errcnt: Displays the statistical information counted as an error for each checking on the target
volumes. Each statistical information counted as an error is cleared when the individual flag for
validation checking is disabled.
gflag: Displays the parameter for guarding on the specified target volumes.
86 Data management commands