HP XP P9000 RAID Manager Reference Guide (T1610-96061, January 2014)

DescriptionOption
CTG P/S Status AP U(%) Q-Marker QM-Cnt SF(%) Seq# IFC OT/s
CT/m RT/m
001 P-VOL PAIR 2 0 00000080 3 50 63528 ON 90
5 5
001 S-VOL PAIR - 0 0000007d - 50 63528 - -
- -
CTG: Displays the CT group ID.
P/S: The attribute of a volume in first LDEV of the specified group.
Status: The status of the paired volume in first LDEV of the specified group.
AP: Displays the number of Active Path in Continuous Access Journal links on PVOL, also displays
the number of active path in Continuous Access Journal links on PVOL and SVOL, 'Unknown'
is shown as '-'.
U(%):The usage sidefile/ journal data, it is valid at PAIR state.
For Continuous Access Synchronous Async: The sidefile percentage for CT Group in relationship
to a 100% full sidefile in cache.
For Continuous Access Journal: The usage rate of the current journal data as 100% of the journal
data space.
Q-Marker: In PVOL, the latest sequence # of the MCU PVol when the write command was
received. In SVOL, the latest sequence # of the DFW on RCU. This item is valid at PAIR state.
QM-Cnt: The number of remaining Q-Marker within CT group of the Unit. Continuous Access
Synchronous Async sends a token called 'dummy recordset' at regular interval time, therefore
QM-Cnt always shows '2' or '3' even if host has NO writing. This item is valid at PAIR state.
SF(%):The usage of cache setting as the sidefile regardless of Continuous Access Journal and
Continuous Access Synchronous Async.
Seq#: The serial number of the RAID storage system.
IFC: Shows 'ON'/ 'OFF' for controlling Inflow.
OT/s: The 'offloading timer' (in unit of Sec.) setting to CT group for Continuous Access
Synchronous Async/Continuous Access Journal. In Continuous Access Journal, this is the same
as 'DOW' item shown by raidvchkscan -v jnlt or pairdisplay -v jnlt.
CT/m: The 'Copy Pending timer' (in unit of Min.) setting to CT group for only Continuous Access
Synchronous Async.
RT/m: The 'RCU Ready timer' (in unit of Min) setting to CT group for only Continuous Access
Synchronous Async.
Note: This option displays nothing if the target volume is NOT Continuous Access Synchronous
Async/Continuous Access Journal volume. The '-FHORC [MU#]' or '-FCA [MU#]' option is used
when displaying the information of cascading Continuous Access Synchronous Async/Continuous
Access Journal volume, and then it shows the CT group information for the remote host only.
Finds the pool ID for each local and remote interconnected to the group via the specified group
or <raw_device>, and displays any information of each pool ID corresponding the local and
-v pid
remote. The first line shows the pool information for the local host, second line shows the pool
information for the remote host. The displayed items are the same as for raidvchkscan -v pid.
Example:
# pairdisplay -g VG01 -v pid
PID POLS U(%) SSCNT Available(MB) Capacity(MB) Seq# Num LDEV# H(%)
127 POLN 0 6 3000 3000 63528 2
864 80
127 POLN 0 6 3000 3000 63528 2
864 80
# pairdisplay -g VG01 -v pid -l
PID POLS U(%) SSCNT Available(MB) Capacity(MB) Seq# Num
LDEV# H(%)
127 POLN 0 6 3000 3000 63528 2
864 80
60 Data management commands