HP XP P9000 RAID Manager Reference Guide (T1610-96061, January 2014)

DescriptionOption
CTG: For Continuous Access Synchronous/Continuous Access Synchronous Async/Continuous
Access Journal, it displays the CT group ID when the Fence is shown as ASYNC. For Continuous
Access Synchronous Sync CTG, displays the CT group ID when the Fence is shown as
DATA/STATUS/NEVER. For Business Copy, it displays the CT group ID on at-time split volumes
using Business Copy.
JID: The journal ID for PVOL or SVOL. In the ESAM configuration, it shows the quorum ID and
the fence level is set to 'Never'. When it is not the Continuous Access Journal/ESAM
configuration, '-' is displayed.
AP: The number of active paths for Continuous Access Journal links on PVOL, and it displays
the number of active paths for Continuous Access Journal links on PVOL and SVOL.'Unknown'is
shown as '-'. Refer to 'MINAP' information that is displayed by running the pairvolchk command.
CM: The Copy mode
• N: Non SnapShot
• S: SnapShot. In the SMPL state, this shows that pair-volume is created as SnapShot.
• C: Cruising Copy
EM: The external connection mode
• H: Mapped E-lun as hidden from the host.
• V: Mapped E-lun as visible to the host
• ' - ': Unmapped to the E-lun
• BH: Mapped E-lun as hidden from the host, but LDEV blockading.
• BV: Mapped E-lun as visible to the host, but LDEV blockading
• B: Unmapped to the E-lun, but LDEV blockading
E-Seq#: The production (serial) number of the external LUN, 'Unknown' is shown as '-'.
E-LDEV#: The LDEV# of the external LUN, 'Unknown' is shown as '-'.
Used when displaying the WWN setting (defined by '50060E80+RAID Type,Serial#,Port#)) to
the port instead of a port name. If this option is specified with the '-fe' option at the same line,
-fw
then 'LUN WWN' appears as shown below. If WWN is not computed, then 'Unknown' appears
(for example, SCSI).
Display example:
# pairdisplay -g PG01 -fw
Group PairVol(L/R) (WWN, LU-M),Seq#,LDEV#.P/S,Status, Seq#,P-LDEV# M
PG01 ora01(L) (500060e804f42001, 3-0) 62496 67. P-VOL COPY, 62496 69
-
PG01 ora01(R) (500060e804f42001, 5-0) 62496 69. S-VOL COPY, ----- 67
-
PG01 ora02(L) (500060e804f42001, 4-0) 62496 68. P-VOL COPY, 62496 64
-
PG01 ora02(R) (500060e804f42001, 6-0) 62496 64. S-VOL COPY, ----- 68
-
Display example:
# pairdisplay -IH -g PG01 -CLI -l -fweGroup PairVol L/R WWN LU Seq# LDEV# P/S Status Fence Seq#
P-LDEV# M CTG JID AP EM E-Seq# E-LDEV# LUN-WWN PG01 oradb01 L 500060e804fa0f01 1 64015 11 P-VOL
PAIR ASYNC 62496
11 - 5 - 1 - - - 60060e8005fa0f000000fa0f0000000b PG01 oradb02 L 500060e804fa0f01 2 64015 12 P-VOL
PAIR ASYNC 62496
12 - 5 - 1 - - - 60060e8005fa0f000000fa0f0000000c
Used when specifying display for command line interface (CLI). This option displays to the same
position that defined number of columns, and displays one header. The delimiters between
columns are displayed as spaces or hyphens (-).
-CLI
Display example:
Group PairVol L/R Port# TID LU-M Seq# LDEV# P/S Status Seq#
P-LDEV# M
homrcf1 deva0 L CL1-D 3 5 0 30053 271 P-VOL PAIR 30053
263 -
homrcf1 deva1 L CL1-D 3 5 1 30053 271 SMPL - -
58 Data management commands