HP XP P9000 for Business Continuity Manager Software Messages

Table 13 Business Continuity Manager error messages and corresponding troubleshooting actions
(message ID YKM7x) (continued)
Explanation and recommended actionsMessage textMessage ID
The value for the year (YYYY), month (MM), or day (DD) was
not numeric. Specify a value for the year, month, and day in
the range 1970–2042, 01 to 12, and 01 to 31, respectively.
The 4-digit year (YYYY) or
2-digit month (MM) or 2-digit
day (DD) was not numeric.
YKM757E ISPF
Valid year values are
1970–2042, valid month
values are 01-12, and valid
day values are 01-31.
The value for the hour, minute, or second was not numeric.
Specify a value for the hour, minute, and second in the range
00 to 23, 00 to 59, and 00 to 59, respectively.
The hour, minute, or second
value is not numeric. Valid
values are 00-23 for hour,
YKM758E ISPF
00-59 for minute, and 00-59
for second.
Enter a numeric value (0-9).Enter numeric characters (0-9).YKM759E ISPF
You cannot set the Preset Mode without specifying a C/T group
ID.
Preset Mode cannot be used
when C/T ID is not specified.
YKM760E ISPF
Check the value specified in Device Num, Volser, or Non
Gen'ed.
Check Device Num, Volser, or
Non Gen'ed.
YKM761E ISPF
You cannot perform a NG scan, because the specified device
address domain ID is the same as the local device address
You cannot perform a NG
scan because the specified
YKM762E ISPF
domain ID or remote device address domain ID. For detailsDADID matches a local or
remote DADID. about the NG scan, see the HP XP P9000 for Business Continuity
Manager Software Reference Guide.
You cannot perform a NG scan, because a local scan has not
been performed for the specified storage system. For details
You cannot perform a NG
scan because no local scan
YKM763E ISPF
about the NG scan, see the HP XP P9000 for Business Continuity
Manager Software Reference Guide.
has been performed for the
specified storage system.
Select one of the displayed lines.Select one of the displayed
lines.
YKM764E ISPF
A description for the specified error code was not found.A description for the specified
error code was not found.
YKM765I ISPF
For details about error codes, see “Storage system sense byte
information” (page 171). If the error code is not listed in the
manual, contact maintenance personnel.
The specified prefix is being used by another program.Specified Prefix is being used
by another program.
YKM766E ISPF
Check the value specified for the prefix.
The command cannot be executed for BC Z copy groups with
the HyperSwap attribute.
This command is invalid for CA
Copy Groups linkaged with
HyperSwap.
YKM767E ISPF
Execute the PPRC copy pair operation from TPC-R.
If a consistency group ID is specified, you cannot specify HS
for the linkage option
HS cannot be used when C/T
ID is specified.
YKM768E ISPF
.
The route label must be an asterisk (*), or a combination of one
or more qualifiers. Each qualifier must be from 1 to 8
Route Label must be an asterisk
(*), or a combination of one
YKM769E ISPF
alphanumeric characters (0-9, AZ, a-z), and must begin withor more qualifiers. Each
an alphabetic character (A-Z, a-z). The length of the route label
must be from 1 to 8 characters
qualifier must be 1-8
alphanumeric characters (0-9,
.A-Z, a-z) with the first character
being an alphabetic character
(AZ, a-z). The length of Route
Label must be 1-8.
List of messages 79