Software Distributor defects fixed in HP-UX 11i v1, v2 and v3

The whatstring: SD-UX/B.11.31.00.194, UDL_11.31_Mar10OEUR_IC346
This release, B.11.11.1003.346, B.11.23.1003.346 and B.11.31.1003.346, can be downloaded from the web. For more
information, see http://www.hp.com/go/sd
Table 2 Defects fixed in March 2010 Web Release
When multiple filesets supersede the same fileset, a WARNING is issued that the conflicting
superseding filesets will not be used. However, their names/specifications is not displayed.
This defect is aimed at fixing this problem by displaying the conflicting fileset names.QXCR1000766167
When swinstall is run in the preview mode for selections including at least one reboot fileset
and autoreboot=false, then swinstall will now print the note saying "-x autoreboot" should
be true. This wasn't printed earlier.QXCR1000822070
With this fix, a depot existing only on the active system can be accessed from the DRD clone
too.QXCR1000941503
With this fix, when swpackage and swmodify are invoked with -C option, the sessions file
is stored only at the location specified with -C and not at the default location. Without the
-C option, it is stored only at the default location.QXCR1000948434
Removal of base product in supersession chain results in top most supersession patch left
and intermediate patches removal. Fix will prevent removal of intermediate patches in
supersession chain.QXCR1000861380
swinstall -p exits with SUCCESS status even though one of the selection not exists on depot.
swinstall is returning with SUCCESS in selection phase. A new option enforce_selections
is added. If enforce_selections option is set to true swinstall will exit with FAILURE, even
when any one selection fails.QXCR1000593453
SD is promoting corequisites to prerequisites in loading order. A new option
loadorder_use_coreqs is used. If loadorder_use_coreqs is set to false, SD will not promote
corequisite to prerequisite in loading order.QXCR1000951260
Enhancement is done to support relative path in source and targets.QXCR1000809519
This fix ensures that if installation of a fileset leads to an unresolved dependency and a new
fileset is selected for installation which is a descendant of the dependent fileset, SD will not
report an error.QXCR1000869644
This fix ensures that when swpackage is interrupted, the depot created is removable using
swremove, even if it is in incomplete or corrupt state.QXCR1000868916
When a depot created using swpackage -x run_as_superuser=false is removed using
swremove -x run_as_superuser=false, the following error is displayed: ERROR:
"<hostname>:<depot_location>An update to the installed product database or depot catalog
may have errors. With this fix, the above errors should not occur.QXCR1000943545
This fix ensures that when an swcopy session fails during selection, analysis or execution
for a new target depot, the target is removable using swremove -d.QXCR1000950487
With this fix, swinstall TUI/GUI with multiple targets will not abnormally terminate on
IA64 machinesQXCR1000963769
Updated SD japanese man pages for 0909 manpage conversionsQXCR1000936854
Man page changes are done to address the new option enforce_selectionsQXCR1000942660
Admin guide changes are made to support relative pathQXCR1000986937
September 2009 Web Release
11.11 SW-DIST fileset revision B.11.11.0909.340
11.23 SW-DIST fileset revision B.11.23.0909.340
11.31 SW-DIST fileset revision B.11.31.0909.340
6