HP-UX Reference (11i v2 07/12) - 1 User Commands A-M (vol 1)

f
fruled(1) fruled(1)
instead allow the command to prompt for the password.
Note: Specifying passwd on the command line will not be supported in future releases.
-h IPaddress|hostname
This option should only be used in combination with either the
-u or -g option.
IPaddress|hostname specifies the IP address or hostname of the target partition (
-u)or
complex (
-g).
-g [passwd] Allows access to the complex specified by the
-h option. The accessed complex is then con-
sidered the target complex. Access is via the service processor’s LAN port.
The
-h option is required if this option is used.
passwd specifies the IPMI password of the service processor. If this field is omitted, the
command prompts for the password.
If an error is reported when you attempt to connect using this option, check to see that
IPMI LAN access has not been disabled on the remote service processor. Access to the
complex via IPMI over LAN can be enabled or disabled by logging on to the service proces-
sor and using the SA command from the Command Menu.
The -u and -g options are mutually exclusive.
SECURITY WARNING: Specifying the password directly on the command line may pose a
security risk in your environment. The ps or other related commands can be invoked in
such a way as to display the command line of a process. In this situation, any authenti-
cated user on the system can potentially see the password while the process is executing.
Hence, it is highly recommended not to specify the password on the command line, and
instead allow the command to prompt for the password.
Note: Specifying passwd on the command line will not be supported in future releases.
-c cell Flash/Turn off the specified cell attention LED.
A cell can be specified either in the local (cabinet#/slot#) or global (cell#) format. For exam-
ple, the cell located in cabinet 0, slot 4 is locally identified as 0/4 or globally as simply 4.
-i I/Ochassis Flash/Turn off the specified I/Ochassis attention LED.
An I/Ochassis must be specified in the form of cabinet#/enclosure#/chassis#. For example,
the I/O chassis located in cabinet 0, enclosure 1 and I/O chassis slot 1 is identified as 0/1/1.
-b cabinet Start flashing or stop flashing the cabinet number LED of the specified cabinet.
-C Turn off all cell attention LEDs.
-I Turn off all I/O chassis LEDs.
-l cabinet Limit the scope of the -C or -I option to a given cabinet.
Mapping of Global Cell Numbers to Local Cell Numbers
The cabinets in a complex are numbered starting from 0. The cell slots in each cabinet are also numbered
starting from 0. Each cabinet can have a maximum of 8 cells. For example, the cells located in cabinet 0
will have the following cell numbers in global format: 0, 1, 2, 3, 4, 5, 6, 7. The cell numbers in correspond-
ing local format will be 0/0, 0/1, 0/2, 0/3, 0/4, 0/5, 0/6, 0/7.
Similarly the cells located in cabinet 1 will have the following cell numbers in global format: 8, 9, 10, 11, 12,
13, 14, 15. The cell numbers in corresponding local format will be 1/0, 1/1, 1/2, 1/3, 1/4, 1/5, 1/6, 1/7.
From the above convention the cell located in cabinet 1, slot 0 is identified in the local format as 1/0 or in
the global format as 8. The
parstatus command will display the above cell as "cab1,cell0". The cell
located in cabinet 1, slot 4 is identified in the local format as 1/4 or in the global format as 12. The
par-
status
command will display the above cell as "cab1,cell4". See parstatus(1).
RETURN VALUE
The fruled command exits with one of the following values:
0 Successful completion.
1 Error condition occurred.
HP-UX 11i Version 2: December 2007 Update − 2 − Hewlett-Packard Company 363