HP-UX Reference (11i v1 00/12) - 1M System Administration Commands N-Z (vol 4)
__________________________________________________________________________________________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________________________________________________________________________
STANDARD Printed by: Nora Chuang [nchuang] STANDARD
/build/1111/BRICK/man1m/naaagt.1m
________________________________________________________________
___ ___
s
swverify(1M) swverify(1M)
(Hewlett-Packard Company)
rpc_binding_info=ncacn_ip_tcp:[2121] ncadg_ip_udp:[2121]
Defines the protocol sequence(s) and endpoint(s) on which the daemon listens and which the
other commands use to contact the daemon. If the connection fails for one protocol
sequence, the next is attempted. SD supports both the tcp (ncacn_ip_tcp:[2121]) and udp
(ncadg_ip_udp:[2121]) protocol sequence on most platforms. See the sd(5) man page by typ-
ing man 5 sd for more information.
rpc_timeout=5
Relative length of the communications timeout. This is a value in the range from 0 to 9 and
is interpreted by the DCE RPC. Higher values mean longer times; you may need a higher
value for a slow or busy network. Lower values will give faster recognition on attempts to
contact hosts that are not up, or are not running swagentd. Each value is approximately
twice as long as the preceding value. A value of 5 is about 30 seconds for the
ncadg_ip_udp protocol sequence. This option may not have any noticeable impact when
using the ncacn_ip_tcp protocol sequence.
run_as_superuser=true
This option controls SD’s nonprivileged mode. This option is ignored (treated as true) when
the invoking user is super-user.
When set to the default value of true, SD operations are performed normally, with permis-
sions for operations either granted to a local super-user or set by SD ACLs. (See swacl(1M)
for details on ACLs.)
When set to false and the invoking user is local and is not super-user, nonprivileged mode
is invoked:
• Permissions for operations are based on the user’s file system permissions.
• SD ACLs are ignored.
• Files created by SD have the uid and gid of the invoking user, and the mode of created
files is set according to the invoking user’s umask.
SD’s nonprivileged mode is intended only for managing applications that are specially
designed and packaged. This mode cannot be used to manage the HP-UX operating system
or patches to it. For a full explanation of nonprivileged SD, see the Software Distributor
Administration Guide, available at the
http://docs.hp.com web site.
See also the
admin_directory
and installed_software_catalog options.
select_local=true
If no target_selections are specified, select the default
target_directory of the local
host as the target_selection for the command.
software=
Defines the default software_selections. There is no supplied default. If there is more than
one software selection, they must be separated by spaces. Software is usually specified in a
software input file, as operands on the command line, or in the GUI.
targets=
Defines the default target_selections. There is no supplied default (see
select_local
above). If there is more than one target selection, they must be separated by spaces. Tar-
gets can be specified in a target input file or as operands on the command line.
verbose=1
Controls the verbosity of a non-interactive command’s output:
0 disables output to stdout. (Error and warning messages are always written to stderr).
1 enables verbose messaging to stdout.
2 for swpackage and swmodify, enables very verbose messaging to stdout.
The -v option overrides this default if it is set to 0.
Session File
Each invocation of the swverify command defines a verify session. The invocation options, source infor-
mation, software selections, and target hosts are saved before the installation or copy task actually com-
mences. This lets you re-execute the command even if the session ends before proper completion.
Each session is saved to the file $HOME/.sw/sessions/swverify.last
. This file is overwritten by
each invocation of
swverify.
Section 1M−−948 − 7 − HP-UX Release 11i: December 2000
___
___