HP-UX Reference (11i v1 00/12) - 1M System Administration Commands N-Z (vol 4)

__________________________________________________________________________________________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________________________________________________________________________
STANDARD Printed by: Nora Chuang [nchuang] STANDARD
/build/1111/BRICK/man1m/naaagt.1m
________________________________________________________________
___ ___
s
swapon(1M) swapon(1M)
Options
swapon recognizes the following options and arguments:
-a Cause all devices marked as swap and all file systems marked as swapfs in the file
/etc/fstab to be made available to the paging system. The options field in
/etc/fstab entries is read by swapon, and must contain elements formatted as
follows:
min=min See the -m option for the value of min.
lim=limit See the -l option for the value of limit. (File system paging areas
only.)
res=reserve See the -r option for the value of reserve. (File system paging areas
only.)
pri=priority See the -p option for the value of priority. (File system paging areas
only.)
end See the -e option for the meaning of this option. (Device paging
areas only.)
See fstab(4) for an example entry.
-e Use space after the end of the file system on the block device for paging. An error
message is returned if no file system is found on the device. This option cannot be
used with the -f option. Do not confuse this with paging to a file system. This option
is for use with a disk that has both a file system and dedicated paging space on it.
-f Force the device to be enabled, which will destroy the file system on it. Use with
extreme caution. Normally, if a file system exists on the device to be enabled,
swapon fails and displays an error message. This option cannot be used with the -e
option.
-l limit limit specifies the maximum space the paging system is allowed to take from the disk,
provided space is available that is not reserved for exclusive use by the file system.
The value of limit is rounded up so that it is a multiple of the paging allocation chunk
size, which is set with the kernel tunable parameter swchunk (see config(1M) and
swapinfo(1M)). See WARNINGS. The default value for limit is 0, indicating there is
no limit to the amount of file system space the paging system can use.
limit can be specified in decimal (no prefix), octal (
0 prefix), or hexadecimal (
0x
prefix). It may be specified in units of kilobytes (k suffix), megabytes (
M suffix), or file
system blocks (no suffix). (A kilobyte is 1024 bytes; a megabyte is 1024 kilobytes; the
size of a file system block is determined by the administrator when the file system is
created.)
-m min min indicates the space the paging system will initiallytake from the file system. The
value of min is rounded up so that it is a multiple of the paging allocation chunk size,
which is set with the kernel tunable parameter swchunk (see config(1M) and
swapinfo(1M)). The default value for min is 0, indicating no paging space is to be allo-
cated initially. min can be specified in the same forms as limit, above.
-p priority priority indicates the order in which space is taken from the file systems and devices
used for paging. Space is taken from the systems with lower priority numbers first.
Under most circumstances, space is taken from device paging areas before file system
paging areas, regardless of priority. See "Paging Allocation" in swapinfo(1M) for more
information. priority can have a value from 0 to 10 and has a default value of 1.
-r reserve reserve specifies the space, in addition to the space currently occupied by the file sys-
tem, that is reserved for file system use only, making it unavailable to the paging sys-
tem. This reserved space is in addition to the minimum free space specified by the
administrator when the file system was created. See WARNINGS. The default value
for reserve is 0 indicating that no file system space is reserved for file system use only.
reserve can be specified in the same forms as limit, above.
-t type Restrict the type of the paging area. If the -t option is omitted, all of the paging
areas defined in
/etc/fstab are made available. type can have one of the following
values:
HP-UX Release 11i: December 2000 − 2 − Section 1M−−845
___
___