HP-UX Reference (11i v1 00/12) - 1 User Commands N-Z (vol 2)

ManualsBrandsHP ManualsSoftwareHP-UX Reference Manuals

381

382

383

384

385

386

387

388

389

390

__________________________________________________________________________________________________________________________________________________________________________________________________

STANDARD Printed by: Nora Chuang [nchuang] STANDARD

/build/1111/BRICK/man1/neqn.1

________________________________________________________________

___ ___

telnet(1) Kerberos telnet(1)

synch Sends the TELNET SYNCH sequence. This sequence causes the remote

system to discard all previously typed (but not yet read) input. This

sequence is sent as TCP urgent data (and may not work to some systems --

if it doesn’t work, a lower case ‘‘r’’ may be echoed on the terminal).

brk Sends the TELNET BRK (Break) sequence, which may have signiﬁcance to

the remote system.

ip Sends the TELNET IP (Interrupt Process) sequence, which should cause

the remote system to abort the currently running process.

ao Sends the TELNET AO (Abort Output) sequence, which should cause the

remote system to ﬂush all output from the remote system to the user’s ter-

minal.

ayt Sends the TELNET AYT (Are You There) sequence, to which the remote

system may or may not choose to respond.

ec Sends the TELNET EC (Erase Character) sequence, which should cause

the remote system to erase the last character entered.

el Sends the TELNET EL (Erase Line) sequence, which should cause the

remote system to erase the line currently being entered.

ga Sends the TELNET GA (Go Ahead) sequence, which likely has no

signiﬁcance to the remote system.

nop Sends the TELNET NOP (No OPeration) sequence.

? Prints out help information for the send command.

set variable_name value

Set any one of a number of telnet variables to a speciﬁc value. The special value

off

turns off the function associated with the variable. The values of variables can be shown by

using the display command. The following variable_names can be speciﬁed:

echo

This is the value (initially ˆE) which, when in line-by-line mode, toggles between

doing local echoing of entered characters (for normal processing), and suppressing

echoing of entered characters (for entering, for example, a password).

escape

This is the telnet escape character (initially ˆ]) which causes entry into telnet

command mode (when connected to a remote system).

interrupt

If telnet is in localchars mode (see toggle localchars below) and the

interrupt character is typed, a TELNET IP sequence (see send ip above) is sent to

the remote host. The initial value for the interrupt character is taken to be the

terminal’s intr character.

quit

If telnet is in localchars mode (see toggle localchars below) and the

quit character is typed, a TELNET BRK sequence (see send brk above) is sent to

the remote host. The initial value for the quit character is taken to be the terminal’s

quit character.

flushoutput

If telnet is in localchars mode (see toggle localchars below) and the

flushoutput character is typed, a TELNET AO sequence (see send ao above) is

sent to the remote host. The initial value for the ﬂush character is ˆO.

erase

If telnet is in localchars mode (see toggle localchars below), and if

telnet is operating in character-at-a-time mode, then when this character is typed,

a TELNET EC sequence (see send ec above) is sent to the remote system. The ini-

tial value for the erase character is taken to be the terminal’s erase character.

kill

If telnet is in localchars mode (see toggle localchars below), and if

telnet is operating in character-at-a-time mode, then when this character is typed,

Section 1−−926 − 3 − HP-UX Release 11i: December 2000

___