HP-UX Reference (11i v1 00/12) - 1 User Commands N-Z (vol 2)

ManualsBrandsHP ManualsSoftwareHP-UX Reference Manuals

381

382

383

384

385

386

387

388

389

390

__________________________________________________________________________________________________________________________________________________________________________________________________

STANDARD Printed by: Nora Chuang [nchuang] STANDARD

/build/1111/BRICK/man1/neqn.1

________________________________________________________________

___ ___

telnet(1) telnet(1)

nop Sends the TELNET NOP (No OPeration) sequence.

? Prints out help information for the send command.

set variable_name value

Set any one of a number of telnet variables to a speciﬁc value. The special value off

turns off the function associated with the variable. The values of variables can be shown by

using the display command. The following variable_names can be speciﬁed:

echo

This is the value (initially ˆE) which, when in line-by-line mode, toggles between

doing local echoing of entered characters (for normal processing), and suppress-

ing echoing of entered characters (for entering, for example, a password).

escape

This is the telnet escape character (initially ˆ]) which causes entry into

telnet command mode (when connected to a remote system).

interrupt

If telnet is in localchars mode (see toggle localchars below) and

the interrupt character is typed, a TELNET IP sequence (see

send ip above)

is sent to the remote host. The initial value for the interrupt character is taken

to be the terminal’s

intr character.

quit

If telnet is in localchars mode (see toggle localchars below) and

the quit character is typed, a TELNET BRK sequence (see send brk above)

is sent to the remote host. The initial value for the quit character is taken to be

the terminal’s quit character.

flushoutput

If telnet is in localchars mode (see toggle localchars below)

and the flushoutput character is typed, a TELNET AO sequence (see

send ao above) is sent to the remote host. The initial value for the ﬂush char-

acter is ˆO.

erase

If telnet is in localchars mode (see toggle localchars below),

and if telnet is operating in character-at-a-time mode, then when this charac-

ter is typed, a TELNET EC sequence (see send ec above) is sent to the

remote system. The initial value for the erase character is taken to be the

terminal’s erase character.

kill

If telnet is in localchars mode (see toggle localchars below),

and if telnet is operating in character-at-a-time mode, then when this charac-

ter is typed, a TELNET EL sequence (see send el above) is sent to the

remote system. The initial value for the kill character is taken to be the

terminal’s kill character.

eof If telnet is operating in line-by-line mode, entering this character as the ﬁrst

character on a line causes this character to be sent to the remote system. The

initial value of the eof character is taken to be the terminal’s eof character.

toggle arguments ...

Toggle (between TRUE and FALSE ) various ﬂags that control how

telnet responds to

events. More than one argument can be speciﬁed. The state of these ﬂags can be shown by

using the

display command. Valid arguments are:

localchars

If TRUE, the flush, interrupt, quit, erase, and kill characters (see

set above) are recognized locally, and transformed into appropriate TELNET

control sequences (respectively ao, ip, brk, ec, and el; see send above).

The initial value for this toggle is

TRUE in line-by-line mode, and FALSE in

character-at-a-time mode.

autoflush

If autoflush and localchars are both TRUE, whenever the ao, intr,

or quit characters are recognized (and transformed into TELNET sequences −

HP-UX Release 11i: December 2000 − 3 − Section 1−−921

___