Offline Diagnostics Environment Administrator's and User's Guide

Reassigning Block:
-----------------
SPARE Reassigns the given block on the disk.
Gathering Disk Information:
--------------------------
DISPMAP Displays a list of all the disks found with their present settings.
DISKINFO Displays the contents of SCSI Inquiry Command for SCSI and Describe
Command for FLEX and CS80 devices.
INQUIRY Use DISKINFO command.
DESCRIBE Use DISKINFO command.
MODESENSE Get mode sense information from SCSI devices only.
Add a Disk Manually:
-------------------
ADDDISK Allows the user to add non-responding disks to the mapped list of
disks.
-------------------------------------------------------------------------------
Continue ([y]/n)? y
ODE Commands Available from DISKEXPT2
Basic Commands
--------------
HELP -- Prints detailed information to the screen, when "help <command>" or "help <var>" is typed
LS -- List modules available on boot medium
RUN -- Run a module (after setting desired environment variables)
Control-Y|Control-C -- Abort an ODE command; pause a module run
RESUME -- Restart a paused module
DISPLOG -- After running a module, display contents of a log
EXIT -- Return to next higher level prompt
Environmental Variables
-----------------------
SHOWSTATE -- Display the value of the following environment variables:
LOOP -- Run a test this many times
ERRPRINT [ON|OFF] -- Print low-level error messages to console
(primarily for manufacturing use)
ERRNUM [ON|OFF] -- Print one-line, numbered errors to the console
Continue ([y]/n)? n
DISKEXPT2> diskinfo
Test Disk (0 - 1 ) ? 0
Peripheral Qualifier: Requested LUN is supported
Peripheral Device Type: Direct-access device
Medium is NOT removable
Device-type Modifier = 0(0x0)
ISO Version = 0 | ECMA Version = 0 | ANSI Version = 3
Reserved
Device does NOT support the TERMINATE I/O PROCESS message
INQUIRY data format is as specified in SCSI-2
Other supported features:
16-bit wide data transfer, Synchronous data transfer, Linked commands, Tagged Command Queuing
This device responds to a RESET condition with a SOFT RESET alternative
Vendor Identification: HP 36.4G
Product Identification: ST336753LC
Product Revision Level: HPC3
Vendor Specific Information:
Addr | Hexadecimal | ASCII
---------------------------------------------------------------------
36 (0x24 ) | 0x33 0x48 0x58 0x30 0x4b 0x38 0x52 0x57 | 3HX0K8RW
44 (0x2c ) | 0x20 0x20 0x20 0x20 0x53 0x45 0x41 0x47 | SEAG
52 (0x34 ) | 0x41 0x54 0x45 0x20 | ATE
Any additional information from the vendor:
Addr | Hexadecimal | ASCII
---------------------------------------------------------------------
96 (0x60 ) | 0x00 0x43 0x6f 0x70 0x79 0x72 0x69 0x67 | .Copyrig
104 (0x68 ) | 0x68 0x74 0x20 0x28 0x63 0x29 0x20 0x32 | ht (c) 2
112 (0x70 ) | 0x30 0x30 0x32 0x20 0x53 0x65 0x61 0x67 | 002 Seag
120 (0x78 ) | 0x61 0x74 0x65 0x20 0x41 0x6c 0x6c 0x20 | ate All
128 (0x80 ) | 0x72 0x69 0x67 0x68 0x74 0x73 0x20 0x72 | rights r
136 (0x88 ) | 0x65 0x73 0x65 0x72 0x76 0x65 0x64 0x20 | eserved
DISKEXPT2> modesense
Test Disk (0 - 1 ) ? 1
---------------------------------------------
POSSIBLE PAGE CODES
---------------------------------------------
0x01 - Read-write error recovery page
0x02 - Disconnect-reconnect page
0x03 - Format device page
0x04 - Rigid disk geometry page
0x05 - Flexible disk page
0x07 - Verify error recovery page
0x08 - Caching Page
0x09 - Peripheral device page
0x0A - Control mode page
0x0B - Medium types supported page
0x0C - Notch and partition page
0x3F - Return all pages
34 Performing Common ODE Tasks