parconfig.1m (2010 09)

p
parconfig(1M) parconfig(1M)
values for a cell are:
ri reactivate with memory interleave. Specifies to integrate the cell as it
would normally be integrated. This is the default for base cells.
float this is the default value for floating cells. If the user specifies ri for a
floating cell, the command displays an error and exits.
deconf deconfigure.
ni no interleave.
clm_value specifies the amount of the memory that will be configured as local (non-
interleaved) memory for the cell. The command will issue a warning if the specified
clm_value exceeds the total memory of the cell.
Note: On PA-RISC platforms, the amount of memory allocated for CLM may not
match the amount of CLM requested due to some memory being reserved
exclusively by the operating system.
If no clm_value is specified, policy rules (specified through
-Z option) will be
applied to the cell to determine the amount of Interleaved memory and Local
Memory for the cell. The command will issue a warning if 100% CLM is specified
for all the cells in the partition. The clm_value can be expressed in two forms:
• As a percentage (ratio).
The percent number can be any number in the range 0 - 100 with a suffix of
%.
This number will be rounded up to 12.5%, 25%, 37.5%, 50%, 62.5%, 75%, 87% or
100%. If the cell contains less than 4 GB memory, then the percentage will be
rounded to 25%, 50%, 75% or 100%. The specified percentage is applied each
time the partition boots, thus resulting in a different value if the working
memory in the cell is different. For example, a cell in a partition has 8 GB
memory and the user specifies 50% CLM. When the partition boots, 4 GB of that
cell’s memory will be used as CLM. Later the user shuts down the partition,
adds another 8 GB memory to that cell. When the partition is booted again, the
cell now has 16 GB of memory, so 8 GB (50%) is allocated as CLM.
• As an absolute number (default).
This can also be optionally suffixed by "GB". The clm_value is interpreted as an
absolute number of gigabytes of memory. Numbers other than integers and
halves are rounded up to the nearest 0.5 GB. For example, 2.5 GB will not be
rounded up. However 2.3 GB will be rounded up to 2.5 GB. For example, a cell
in a partition has 8 GB memory and the user specifies 4 GB CLM. When the
partition boots 4 GB of that cell’s memory will be used as CLM. Later the user
shuts down the partition, adds another 8 GB memory to that cell. When the par-
tition is booted again, the cell now has 16 GB of memory, but the CLM is still 4
GB.
Note: The optional cell attribute celltype and/or clm_value , if specified, should be in
line with the policy rules (specified through the
-Z option).
-g -h IPaddress|hostname
Allows access to the complex specified by the -h option. The accessed complex is
then considered the target complex. Access is through the service processor’s LAN
port.
The
-h option is required if -g is used.
If the
-g option is specified, the command prompts for the password.
If an error is reported when you attempt to connect using this option, check to see
that IPMI LAN access has not been disabled on the remote service processor.
Access to the complex through IPMI over LAN can be enabled or disabled by logging
on to the service processor and using the
SA command from the Command Menu.
The
-u and -g options are mutually exclusive.
-h IPaddress|hostname
This option should only be used in combination with either the -u or -g option.
IPaddress|hostname specifies the IP address or hostname, respectively, of the tar-
get partition (-u) or complex (-g).
2 Hewlett-Packard Company − 2 − HP-UX 11i Version 3: September 2010